📄 at91sam7s64.h
字号:
AT91_REG SPI_TDR; // Transmit Data Register
AT91_REG SPI_SR; // Status Register
AT91_REG SPI_IER; // Interrupt Enable Register
AT91_REG SPI_IDR; // Interrupt Disable Register
AT91_REG SPI_IMR; // Interrupt Mask Register
AT91_REG Reserved0[4]; //
AT91_REG SPI_CSR[4]; // Chip Select Register
AT91_REG Reserved1[48]; //
AT91_REG SPI_RPR; // Receive Pointer Register
AT91_REG SPI_RCR; // Receive Counter Register
AT91_REG SPI_TPR; // Transmit Pointer Register
AT91_REG SPI_TCR; // Transmit Counter Register
AT91_REG SPI_RNPR; // Receive Next Pointer Register
AT91_REG SPI_RNCR; // Receive Next Counter Register
AT91_REG SPI_TNPR; // Transmit Next Pointer Register
AT91_REG SPI_TNCR; // Transmit Next Counter Register
AT91_REG SPI_PTCR; // PDC Transfer Control Register
AT91_REG SPI_PTSR; // PDC Transfer Status Register
} AT91S_SPI, *AT91PS_SPI;
#else
#define SPI_CR (AT91_CAST(AT91_REG *) 0x00000000) // (SPI_CR) Control Register
#define SPI_MR (AT91_CAST(AT91_REG *) 0x00000004) // (SPI_MR) Mode Register
#define SPI_RDR (AT91_CAST(AT91_REG *) 0x00000008) // (SPI_RDR) Receive Data Register
#define SPI_TDR (AT91_CAST(AT91_REG *) 0x0000000C) // (SPI_TDR) Transmit Data Register
#define SPI_SR (AT91_CAST(AT91_REG *) 0x00000010) // (SPI_SR) Status Register
#define SPI_IER (AT91_CAST(AT91_REG *) 0x00000014) // (SPI_IER) Interrupt Enable Register
#define SPI_IDR (AT91_CAST(AT91_REG *) 0x00000018) // (SPI_IDR) Interrupt Disable Register
#define SPI_IMR (AT91_CAST(AT91_REG *) 0x0000001C) // (SPI_IMR) Interrupt Mask Register
#define SPI_CSR (AT91_CAST(AT91_REG *) 0x00000030) // (SPI_CSR) Chip Select Register
#endif
// -------- SPI_CR : (SPI Offset: 0x0) SPI Control Register --------
#define AT91C_SPI_SPIEN (0x1 << 0) // (SPI) SPI Enable
#define AT91C_SPI_SPIDIS (0x1 << 1) // (SPI) SPI Disable
#define AT91C_SPI_SWRST (0x1 << 7) // (SPI) SPI Software reset
#define AT91C_SPI_LASTXFER (0x1 << 24) // (SPI) SPI Last Transfer
// -------- SPI_MR : (SPI Offset: 0x4) SPI Mode Register --------
#define AT91C_SPI_MSTR (0x1 << 0) // (SPI) Master/Slave Mode
#define AT91C_SPI_PS (0x1 << 1) // (SPI) Peripheral Select
#define AT91C_SPI_PS_FIXED (0x0 << 1) // (SPI) Fixed Peripheral Select
#define AT91C_SPI_PS_VARIABLE (0x1 << 1) // (SPI) Variable Peripheral Select
#define AT91C_SPI_PCSDEC (0x1 << 2) // (SPI) Chip Select Decode
#define AT91C_SPI_FDIV (0x1 << 3) // (SPI) Clock Selection
#define AT91C_SPI_MODFDIS (0x1 << 4) // (SPI) Mode Fault Detection
#define AT91C_SPI_LLB (0x1 << 7) // (SPI) Clock Selection
#define AT91C_SPI_PCS (0xF << 16) // (SPI) Peripheral Chip Select
#define AT91C_SPI_DLYBCS (0xFF << 24) // (SPI) Delay Between Chip Selects
// -------- SPI_RDR : (SPI Offset: 0x8) Receive Data Register --------
#define AT91C_SPI_RD (0xFFFF << 0) // (SPI) Receive Data
#define AT91C_SPI_RPCS (0xF << 16) // (SPI) Peripheral Chip Select Status
// -------- SPI_TDR : (SPI Offset: 0xc) Transmit Data Register --------
#define AT91C_SPI_TD (0xFFFF << 0) // (SPI) Transmit Data
#define AT91C_SPI_TPCS (0xF << 16) // (SPI) Peripheral Chip Select Status
// -------- SPI_SR : (SPI Offset: 0x10) Status Register --------
#define AT91C_SPI_RDRF (0x1 << 0) // (SPI) Receive Data Register Full
#define AT91C_SPI_TDRE (0x1 << 1) // (SPI) Transmit Data Register Empty
#define AT91C_SPI_MODF (0x1 << 2) // (SPI) Mode Fault Error
#define AT91C_SPI_OVRES (0x1 << 3) // (SPI) Overrun Error Status
#define AT91C_SPI_ENDRX (0x1 << 4) // (SPI) End of Receiver Transfer
#define AT91C_SPI_ENDTX (0x1 << 5) // (SPI) End of Receiver Transfer
#define AT91C_SPI_RXBUFF (0x1 << 6) // (SPI) RXBUFF Interrupt
#define AT91C_SPI_TXBUFE (0x1 << 7) // (SPI) TXBUFE Interrupt
#define AT91C_SPI_NSSR (0x1 << 8) // (SPI) NSSR Interrupt
#define AT91C_SPI_TXEMPTY (0x1 << 9) // (SPI) TXEMPTY Interrupt
#define AT91C_SPI_SPIENS (0x1 << 16) // (SPI) Enable Status
// -------- SPI_IER : (SPI Offset: 0x14) Interrupt Enable Register --------
// -------- SPI_IDR : (SPI Offset: 0x18) Interrupt Disable Register --------
// -------- SPI_IMR : (SPI Offset: 0x1c) Interrupt Mask Register --------
// -------- SPI_CSR : (SPI Offset: 0x30) Chip Select Register --------
#define AT91C_SPI_CPOL (0x1 << 0) // (SPI) Clock Polarity
#define AT91C_SPI_NCPHA (0x1 << 1) // (SPI) Clock Phase
#define AT91C_SPI_CSAAT (0x1 << 3) // (SPI) Chip Select Active After Transfer
#define AT91C_SPI_BITS (0xF << 4) // (SPI) Bits Per Transfer
#define AT91C_SPI_BITS_8 (0x0 << 4) // (SPI) 8 Bits Per transfer
#define AT91C_SPI_BITS_9 (0x1 << 4) // (SPI) 9 Bits Per transfer
#define AT91C_SPI_BITS_10 (0x2 << 4) // (SPI) 10 Bits Per transfer
#define AT91C_SPI_BITS_11 (0x3 << 4) // (SPI) 11 Bits Per transfer
#define AT91C_SPI_BITS_12 (0x4 << 4) // (SPI) 12 Bits Per transfer
#define AT91C_SPI_BITS_13 (0x5 << 4) // (SPI) 13 Bits Per transfer
#define AT91C_SPI_BITS_14 (0x6 << 4) // (SPI) 14 Bits Per transfer
#define AT91C_SPI_BITS_15 (0x7 << 4) // (SPI) 15 Bits Per transfer
#define AT91C_SPI_BITS_16 (0x8 << 4) // (SPI) 16 Bits Per transfer
#define AT91C_SPI_SCBR (0xFF << 8) // (SPI) Serial Clock Baud Rate
#define AT91C_SPI_DLYBS (0xFF << 16) // (SPI) Delay Before SPCK
#define AT91C_SPI_DLYBCT (0xFF << 24) // (SPI) Delay Between Consecutive Transfers
// *****************************************************************************
// SOFTWARE API DEFINITION FOR Analog to Digital Convertor
// *****************************************************************************
#ifndef __ASSEMBLY__
typedef struct _AT91S_ADC {
AT91_REG ADC_CR; // ADC Control Register
AT91_REG ADC_MR; // ADC Mode Register
AT91_REG Reserved0[2]; //
AT91_REG ADC_CHER; // ADC Channel Enable Register
AT91_REG ADC_CHDR; // ADC Channel Disable Register
AT91_REG ADC_CHSR; // ADC Channel Status Register
AT91_REG ADC_SR; // ADC Status Register
AT91_REG ADC_LCDR; // ADC Last Converted Data Register
AT91_REG ADC_IER; // ADC Interrupt Enable Register
AT91_REG ADC_IDR; // ADC Interrupt Disable Register
AT91_REG ADC_IMR; // ADC Interrupt Mask Register
AT91_REG ADC_CDR0; // ADC Channel Data Register 0
AT91_REG ADC_CDR1; // ADC Channel Data Register 1
AT91_REG ADC_CDR2; // ADC Channel Data Register 2
AT91_REG ADC_CDR3; // ADC Channel Data Register 3
AT91_REG ADC_CDR4; // ADC Channel Data Register 4
AT91_REG ADC_CDR5; // ADC Channel Data Register 5
AT91_REG ADC_CDR6; // ADC Channel Data Register 6
AT91_REG ADC_CDR7; // ADC Channel Data Register 7
AT91_REG Reserved1[44]; //
AT91_REG ADC_RPR; // Receive Pointer Register
AT91_REG ADC_RCR; // Receive Counter Register
AT91_REG ADC_TPR; // Transmit Pointer Register
AT91_REG ADC_TCR; // Transmit Counter Register
AT91_REG ADC_RNPR; // Receive Next Pointer Register
AT91_REG ADC_RNCR; // Receive Next Counter Register
AT91_REG ADC_TNPR; // Transmit Next Pointer Register
AT91_REG ADC_TNCR; // Transmit Next Counter Register
AT91_REG ADC_PTCR; // PDC Transfer Control Register
AT91_REG ADC_PTSR; // PDC Transfer Status Register
} AT91S_ADC, *AT91PS_ADC;
#else
#define ADC_CR (AT91_CAST(AT91_REG *) 0x00000000) // (ADC_CR) ADC Control Register
#define ADC_MR (AT91_CAST(AT91_REG *) 0x00000004) // (ADC_MR) ADC Mode Register
#define ADC_CHER (AT91_CAST(AT91_REG *) 0x00000010) // (ADC_CHER) ADC Channel Enable Register
#define ADC_CHDR (AT91_CAST(AT91_REG *) 0x00000014) // (ADC_CHDR) ADC Channel Disable Register
#define ADC_CHSR (AT91_CAST(AT91_REG *) 0x00000018) // (ADC_CHSR) ADC Channel Status Register
#define ADC_SR (AT91_CAST(AT91_REG *) 0x0000001C) // (ADC_SR) ADC Status Register
#define ADC_LCDR (AT91_CAST(AT91_REG *) 0x00000020) // (ADC_LCDR) ADC Last Converted Data Register
#define ADC_IER (AT91_CAST(AT91_REG *) 0x00000024) // (ADC_IER) ADC Interrupt Enable Register
#define ADC_IDR (AT91_CAST(AT91_REG *) 0x00000028) // (ADC_IDR) ADC Interrupt Disable Register
#define ADC_IMR (AT91_CAST(AT91_REG *) 0x0000002C) // (ADC_IMR) ADC Interrupt Mask Register
#define ADC_CDR0 (AT91_CAST(AT91_REG *) 0x00000030) // (ADC_CDR0) ADC Channel Data Register 0
#define ADC_CDR1 (AT91_CAST(AT91_REG *) 0x00000034) // (ADC_CDR1) ADC Channel Data Register 1
#define ADC_CDR2 (AT91_CAST(AT91_REG *) 0x00000038) // (ADC_CDR2) ADC Channel Data Register 2
#define ADC_CDR3 (AT91_CAST(AT91_REG *) 0x0000003C) // (ADC_CDR3) ADC Channel Data Register 3
#define ADC_CDR4 (AT91_CAST(AT91_REG *) 0x00000040) // (ADC_CDR4) ADC Channel Data Register 4
#define ADC_CDR5 (AT91_CAST(AT91_REG *) 0x00000044) // (ADC_CDR5) ADC Channel Data Register 5
#define ADC_CDR6 (AT91_CAST(AT91_REG *) 0x00000048) // (ADC_CDR6) ADC Channel Data Register 6
#define ADC_CDR7 (AT91_CAST(AT91_REG *) 0x0000004C) // (ADC_CDR7) ADC Channel Data Register 7
#endif
// -------- ADC_CR : (ADC Offset: 0x0) ADC Control Register --------
#define AT91C_ADC_SWRST (0x1 << 0) // (ADC) Software Reset
#define AT91C_ADC_START (0x1 << 1) // (ADC) Start Conversion
// -------- ADC_MR : (ADC Offset: 0x4) ADC Mode Register --------
#define AT91C_ADC_TRGEN (0x1 << 0) // (ADC) Trigger Enable
#define AT91C_ADC_TRGEN_DIS (0x0) // (ADC) Hradware triggers are disabled. Starting a conversion is only possible by software
#define AT91C_ADC_TRGEN_EN (0x1) // (ADC) Hardware trigger selected by TRGSEL field is enabled.
#define AT91C_ADC_TRGSEL (0x7 << 1) // (ADC) Trigger Selection
#define AT91C_ADC_TRGSEL_TIOA0 (0x0 << 1) // (ADC) Selected TRGSEL = TIAO0
#define AT91C_ADC_TRGSEL_TIOA1 (0x1 << 1) // (ADC) Selected TRGSEL = TIAO1
#define AT91C_ADC_TRGSEL_TIOA2 (0x2 << 1) // (ADC) Selected TRGSEL = TIAO2
#define AT91C_ADC_TRGSEL_TIOA3 (0x3 << 1) // (ADC) Selected TRGSEL = TIAO3
#define AT91C_ADC_TRGSEL_TIOA4 (0x4 << 1) // (ADC) Selected TRGSEL = TIAO4
#define AT91C_ADC_TRGSEL_TIOA5 (0x5 << 1) // (ADC) Selected TRGSEL = TIAO5
#define AT91C_ADC_TRGSEL_EXT (0x6 << 1) // (ADC) Selected TRGSEL = External Trigger
#define AT91C_ADC_LOWRES (0x1 << 4) // (ADC) Resolution.
#define AT91C_ADC_LOWRES_10_BIT (0x0 << 4) // (ADC) 10-bit resolution
#define AT91C_ADC_LOWRES_8_BIT (0x1 << 4) // (ADC) 8-bit resolution
#define AT91C_ADC_SLEEP (0x1 << 5) // (ADC) Sleep Mode
#define AT91C_ADC_SLEEP_NORMAL_MODE (0x0 << 5) // (ADC) Normal Mode
#define AT91C_ADC_SLEEP_MODE (0x1 << 5) // (ADC) Sleep Mode
#define AT91C_ADC_PRESCAL (0x3F << 8) // (ADC) Prescaler rate selection
#define AT91C_ADC_STARTUP (0x1F << 16) // (ADC) Startup Time
#define AT91C_ADC_SHTIM (0xF << 24) // (ADC) Sample & Hold Time
// -------- ADC_CHER : (ADC Offset: 0x10) ADC Channel Enable Register --------
#define AT91C_ADC_CH0 (0x1 << 0) // (ADC) Channel 0
#define AT91C_ADC_CH1 (0x1 << 1) // (ADC) Channel 1
#define AT91C_ADC_CH2 (0x1 << 2) // (ADC) Channel 2
#define AT91C_ADC_CH3 (0x1 << 3) // (ADC) Channel 3
#define AT91C_ADC_CH4 (0x1 << 4) // (ADC) Channel 4
#define AT91C_ADC_CH5 (0x1 << 5) // (ADC) Channel 5
#define AT91C_ADC_CH6 (0x1 << 6) // (ADC) Channel 6
#define AT91C_ADC_CH7 (0x1 << 7) // (ADC) Channel 7
// -------- ADC_CHDR : (ADC Offset: 0x14) ADC Channel Disable Register --------
// -------- ADC_CHSR : (ADC Offset: 0x18) ADC Channel Status Register --------
// -------- ADC_SR : (ADC Offset: 0x1c) ADC Status Register --------
#define AT91C_ADC_EOC0 (0x1 << 0) // (ADC) End of Conversion
#define AT91C_ADC_EOC1 (0x1 << 1) // (ADC) End of Conversion
#define AT91C_ADC_EOC2 (0x1 << 2) // (ADC) End of Conversion
#define AT91C_ADC_EOC3 (0x1 << 3) // (ADC) End of Conversion
#define AT91C_ADC_EOC4 (0x1 << 4) // (ADC) End of Conversion
#define AT91C_ADC_EOC5 (0x1 << 5) // (ADC) End of Conversion
#define AT91C_ADC_EOC6 (0x1 << 6) // (ADC) End of Conversion
#define AT91C_ADC_EOC7 (0x1 << 7) // (ADC) End of Conversion
#define AT91C_ADC_OVRE0 (0x1 << 8) // (ADC) Overrun Error
#define AT91C_ADC_OVRE1 (0x1 << 9) // (ADC) Overrun Error
#define AT91C_ADC_OVRE2 (0x1 << 10) // (ADC) Overrun Error
#define AT91C_ADC_OVRE3 (0x1 << 11) // (ADC) Overrun Error
#define AT91C_ADC_OVRE4 (0x1 << 12) // (ADC) Overrun Error
#define AT91C_ADC_OVRE5 (0x1 << 13) // (ADC) Overrun Error
#define AT91C_ADC_OVRE6 (0x1 << 14) // (ADC) Overrun Error
#define AT91C_ADC_OVRE7 (0x1 << 15) // (ADC) Overrun Error
#define AT91C_ADC_DRDY (0x1 << 16) // (ADC) Data Ready
#define AT91C_ADC_GOVRE (0x1 << 17) // (ADC) General Overrun
#define AT91C_ADC_ENDRX (0x1 << 18) // (ADC) End of Receiver Transfer
#define AT91C_ADC_RXB⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -