startup.s

Hitex LPC2100 insider guide source code

/***********************************************************************/
#/*  This file is part of the uVision/ARM development tools             */
#/*  Copyright KEIL ELEKTRONIK GmbH 2002-2003                           */
#/***********************************************************************/
#/*                                                                     */
#/*  STARTUP.S:  Startup file for the Blinky Example                    */
#/*                                                                     */
#/***********************************************************************/


/* 
//*** <<< Use Configuration Wizard in Context Menu >>> *** 
*/


# *** Startup Code (executed after Reset) ***


# Standard definitions of Mode bits and Interrupt (I & F) flags in PSRs

        .equ    Mode_USR,       0x10
        .equ    Mode_FIQ,       0x11
        .equ    Mode_IRQ,       0x12
        .equ    Mode_SVC,       0x13
        .equ    Mode_ABT,       0x17
        .equ    Mode_UND,       0x1B
        .equ    Mode_SYS,       0x1F

        .equ    I_Bit,          0x80    /* when I bit is set, IRQ is disabled */
        .equ    F_Bit,          0x40    /* when F bit is set, FIQ is disabled */


/*
// <h> Stack Configuration
//   <o>  Top of Stack Address  <0x0-0xFFFFFFFF>
//   <h>  Stack Sizes (in Bytes)
//     <o1> Undefined Mode      <0x0-0xFFFFFFFF>
//     <o2> Supervisor Mode     <0x0-0xFFFFFFFF>
//     <o3> Abort Mode          <0x0-0xFFFFFFFF>
//     <o4> Fast Interrupt Mode <0x0-0xFFFFFFFF>
//     <o5> Interrupt Mode      <0x0-0xFFFFFFFF>
//     <o6> User/System Mode    <0x0-0xFFFFFFFF>
//   </h>
// </h>
*/
        .equ    Top_Stack,      0x40004000
        .equ    UND_Stack_Size, 0x00000004
        .equ    SVC_Stack_Size, 0x00000040
        .equ    ABT_Stack_Size, 0x00000040
        .equ    FIQ_Stack_Size, 0x00000040
        .equ    IRQ_Stack_Size, 0x00000080
        .equ    USR_Stack_Size, 0x00000400


# Phase Locked Loop (PLL) definitions
        .equ    PLL_BASE,       0xE01FC080  /* PLL Base Address */
        .equ    PLLCON_OFS,     0x00        /* PLL Control Offset*/
        .equ    PLLCFG_OFS,     0x04        /* PLL Configuration Offset */
        .equ    PLLSTAT_OFS,    0x08        /* PLL Status Offset */
        .equ    PLLFEED_OFS,    0x0C        /* PLL Feed Offset */
        .equ    PLLCON_PLLE,    (1<<0)      /* PLL Enable */
        .equ    PLLCON_PLLC,    (1<<1)      /* PLL Connect */
        .equ    PLLCFG_MSEL,    (0x1F<<0)   /* PLL Multiplier */
        .equ    PLLCFG_PSEL,    (0x03<<5)   /* PLL Divider */
        .equ    PLLSTAT_PLOCK,  (1<<10)     /* PLL Lock Status */

/*
// <e> PLL Setup
//   <o1.0..4>   MSEL: PLL Multiplier Selection
//               <1-32><#-1>
//               <i> M Value
//   <o1.5..6>   PSEL: PLL Divider Selection
//               <0=> 1   <1=> 2   <2=> 4   <3=> 8
//               <i> P Value
// </e>
*/
        .equ    PLL_SETUP,      1
        .equ    PLLCFG_Val,     0x00000024

		.equ	RAM_Mode,		1

# Starupt Code must be linked first at Address at which it expects to run.

        .text
        .arm
		.extern  SWI_ISR
        .global _startup
        .func   _startup
_startup:


# Exception Vectors
#  Mapped to Address 0.
#  Absolute addressing mode must be used.
#  Dummy Handlers are implemented as infinite loops which can be modified.

Vectors:        LDR     PC, Reset_Addr         
                LDR     PC, Undef_Addr
                LDR     PC, SWI_Addr
                LDR     PC, PAbt_Addr
                LDR     PC, DAbt_Addr
                 .long 0xB8A06F58                          /* Reserved Vector */
                LDR     PC, IRQ_Addr
                LDR     PC, FIQ_Addr

Reset_Addr:     .word   Reset_Handler
Undef_Addr:     .word   Undef_Handler
SWI_Addr:       .word   SWI_ISR
PAbt_Addr:      .word   PAbt_Handler
DAbt_Addr:      .word   DAbt_Handler
                .word   0                      /* Reserved Address */
IRQ_Addr:       .word   IRQ_Handler
FIQ_Addr:       .word   FIQ_Handler

Undef_Handler:  B       Undef_Handler
SWI_Handler:    B       SWI_Handler
PAbt_Handler:   B       PAbt_Handler
DAbt_Handler:   B       DAbt_Handler
IRQ_Handler:    B       IRQ_Handler
FIQ_Handler:    B       FIQ_Handler


# Reset Handler

Reset_Handler:  

.if PLL_SETUP
                LDR     R0, =PLL_BASE
                MOV     R1, #0xAA
                MOV     R2, #0x55

# Configure and Enable PLL
                MOV     R3, #PLLCFG_Val
                STR     R3, [R0, #PLLCFG_OFS] 
                MOV     R3, #PLLCON_PLLE
                STR     R3, [R0, #PLLCON_OFS]
                STR     R1, [R0, #PLLFEED_OFS]
                STR     R2, [R0, #PLLFEED_OFS]

# Wait until PLL Locked
PLL_Loop:       LDR     R3, [R0, #PLLSTAT_OFS]
                ANDS    R3, R3, #PLLSTAT_PLOCK
                BEQ     PLL_Loop

# Switch to PLL Clock
                MOV     R3, #(PLLCON_PLLE | PLLCON_PLLC)
                STR     R3, [R0, #PLLCON_OFS]
                STR     R1, [R0, #PLLFEED_OFS]
                STR     R2, [R0, #PLLFEED_OFS]
.endif


# Initialise Interrupt System
#  ...


# Setup Stack for each mode

                LDR     R0, =Top_Stack

#  Enter Undefined Instruction Mode and set its Stack Pointer
                MSR     CPSR_c, #Mode_UND|I_Bit|F_Bit
                MOV     SP, R0
                SUB     R0, R0, #UND_Stack_Size

#  Enter Abort Mode and set its Stack Pointer
                MSR     CPSR_c, #Mode_ABT|I_Bit|F_Bit
                MOV     SP, R0
                SUB     R0, R0, #ABT_Stack_Size

#  Enter FIQ Mode and set its Stack Pointer
                MSR     CPSR_c, #Mode_FIQ|I_Bit|F_Bit
                MOV     SP, R0
                SUB     R0, R0, #FIQ_Stack_Size

#  Enter IRQ Mode and set its Stack Pointer
                MSR     CPSR_c, #Mode_IRQ|I_Bit|F_Bit
                MOV     SP, R0
                SUB     R0, R0, #IRQ_Stack_Size

#  Enter Supervisor Mode and set its Stack Pointer
                MSR     CPSR_c, #Mode_SVC|I_Bit|F_Bit
                MOV     SP, R0
                SUB     R0, R0, #SVC_Stack_Size

#  Enter User Mode and set its Stack Pointer
                MSR     CPSR_c, #Mode_USR
                MOV     SP, R0

#  Setup a default Stack Limit (when compiled with "-mapcs-stack-check")
                SUB     SL, SP, #USR_Stack_Size


# Relocate .data section (Copy from ROM to RAM)
                LDR     R1, =_etext
                LDR     R2, =_data
                LDR     R3, =_edata
LoopRel:        CMP     R2, R3
                LDRLO   R0, [R1], #4
                STRLO   R0, [R2], #4
                BLO     LoopRel


# Clear .bss section (Zero init)
                MOV     R0, #0
                LDR     R1, =__bss_start__
                LDR     R2, =__bss_end__
LoopZI:         CMP     R1, R2
                STRLO   R0, [R1], #4
                BLO     LoopZI


# Enter the C code
                B       main


        .size   _startup, . - _startup
        .endfunc


        .end