kconfig

优龙2410linux2.6.8内核源代码

#
# Sensor device configuration
#

menu "I2C Hardware Bus support"
	depends on I2C

config I2C_ALI1535
	tristate "ALI 1535"
	depends on I2C && PCI && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for the SMB
	  Host controller on Acer Labs Inc. (ALI) M1535 South Bridges.  The SMB
	  controller is part of the 7101 device, which is an ACPI-compliant
	  Power Management Unit (PMU).

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-ali1535.

config I2C_ALI1563
	tristate "ALI 1563"
	depends on I2C && PCI && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for the SMB
	  Host controller on Acer Labs Inc. (ALI) M1563 South Bridges.  The SMB
	  controller is part of the 7101 device, which is an ACPI-compliant
	  Power Management Unit (PMU).

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-ali1563.

config I2C_ALI15X3
	tristate "ALI 15x3"
	depends on I2C && PCI && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for the
	  Acer Labs Inc. (ALI) M1514 and M1543 motherboard I2C interfaces.

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-ali15x3.

config I2C_AMD756
	tristate "AMD 756/766"
	depends on I2C && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for the AMD
	  756/766/768 mainboard I2C interfaces.

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-amd756.

config I2C_AMD8111
	tristate "AMD 8111"
	depends on I2C && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for the AMD
	  8111 mainboard I2C interfaces.

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-amd8111.

config I2C_ELEKTOR
	tristate "Elektor ISA card"
	depends on I2C && ISA && BROKEN_ON_SMP
	select I2C_ALGOPCF
	help
	  This supports the PCF8584 ISA bus I2C adapter.  Say Y if you own
	  such an adapter.

	  This support is also available as a module.  If so, the module 
	  will be called i2c-elektor.

config I2C_HYDRA
	tristate "CHRP Apple Hydra Mac I/O I2C interface"
	depends on I2C && PCI && PPC_CHRP && EXPERIMENTAL
	select I2C_ALGOBIT
	help
	  This supports the use of the I2C interface in the Apple Hydra Mac
	  I/O chip on some CHRP machines (e.g. the LongTrail).  Say Y if you
	  have such a machine.

	  This support is also available as a module.  If so, the module
	  will be called i2c-hydra.

config I2C_I801
	tristate "Intel 801"
	depends on I2C && PCI && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for the Intel
	  801 family of mainboard I2C interfaces.  Specifically, the following
	  versions of the chipset are supported:
	    82801AA
	    82801AB
	    82801BA
	    82801CA/CAM
	    82801DB
	    82801EB
	    6300ESB
	    ICH6

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-i801.

config I2C_I810
	tristate "Intel 810/815"
	depends on I2C && PCI && EXPERIMENTAL
	select I2C_ALGOBIT
	help
	  If you say yes to this option, support will be included for the Intel
	  810/815 family of mainboard I2C interfaces.  Specifically, the 
	  following versions of the chipset is supported:
	    i810AA
	    i810AB
	    i810E
	    i815

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-i810.

config I2C_IBM_IIC
	tristate "IBM PPC 4xx on-chip I2C interface"
	depends on IBM_OCP && I2C
	help
	  Say Y here if you want to use IIC peripheral found on 
	  embedded IBM PPC 4xx based systems. 

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-ibm_iic.

config I2C_IOP3XX
	tristate "Intel XScale IOP3xx on-chip I2C interface"
	depends on ARCH_IOP3XX && I2C

config I2C_ISA
	tristate "ISA Bus support"
	depends on I2C && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for i2c
	  interfaces that are on the ISA bus.

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-isa.

config I2C_ITE
	tristate "ITE I2C Adapter"
	depends on I2C && MIPS_ITE8172
	select I2C_ALGOITE
	help
	  This supports the ITE8172 I2C peripheral found on some MIPS
	  systems. Say Y if you have one of these. You should also say Y for
	  the ITE I2C driver algorithm support above.

	  This support is also available as a module.  If so, the module 
	  will be called i2c-ite.

config I2C_IXP4XX
	tristate "IXP4xx GPIO-Based I2C Interface"
	depends on I2C && ARCH_IXP4XX
	select I2C_ALGOBIT
	help
	  Say Y here if you have an Intel IXP4xx(420,421,422,425) based 
	  system and are using GPIO lines for an I2C bus.

	  This support is also available as a module. If so, the module
	  will be called i2c-ixp4xx.

config I2C_KEYWEST
	tristate "Powermac Keywest I2C interface"
	depends on I2C && PPC_PMAC
	help
	  This supports the use of the I2C interface in the combo-I/O
	  chip on recent Apple machines.  Say Y if you have such a machine.

	  This support is also available as a module.  If so, the module 
	  will be called i2c-keywest.

config I2C_IMX
	tristate "Motorola IMX"
	depends on I2C && ARCH_IMX
	help
	  Motorola IMX I2C support

								
config I2C_NFORCE2
	tristate "Nvidia Nforce2"
	depends on I2C && PCI && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for the Nvidia
	  Nforce2 family of mainboard I2C interfaces.

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-nforce2.

config I2C_PARPORT
	tristate "Parallel port adapter"
	depends on I2C && PARPORT
	select I2C_ALGOBIT
	help
	  This supports parallel port I2C adapters such as the ones made by
	  Philips or Velleman, Analog Devices evaluation boards, and more.
	  Basically any adapter using the parallel port as an I2C bus with
	  no extra chipset is supported by this driver, or could be.

	  This driver is a replacement for (and was inspired by) an older
	  driver named i2c-philips-par.  The new driver supports more devices,
	  and makes it easier to add support for new devices.
	  
	  Another driver exists, named i2c-parport-light, which doesn't depend
	  on the parport driver.  This is meant for embedded systems. Don't say
	  Y here if you intend to say Y or M there.

	  This support is also available as a module.  If so, the module 
	  will be called i2c-parport.

config I2C_PARPORT_LIGHT
	tristate "Parallel port adapter (light)"
	depends on I2C
	select I2C_ALGOBIT
	help
	  This supports parallel port I2C adapters such as the ones made by
	  Philips or Velleman, Analog Devices evaluation boards, and more.
	  Basically any adapter using the parallel port as an I2C bus with
	  no extra chipset is supported by this driver, or could be.

	  This driver is a light version of i2c-parport.  It doesn't depend
	  on the parport driver, and uses direct I/O access instead.  This
	  might be prefered on embedded systems where wasting memory for
	  the clean but heavy parport handling is not an option.  The
	  drawback is a reduced portability and the impossibility to
	  dasiy-chain other parallel port devices.
	  
	  Don't say Y here if you said Y or M to i2c-parport.  Saying M to
	  both is possible but both modules should not be loaded at the same
	  time.

	  This support is also available as a module.  If so, the module 
	  will be called i2c-parport-light.

config I2C_PIIX4
	tristate "Intel PIIX4"
	depends on I2C && PCI && EXPERIMENTAL && !64BIT
	help
	  If you say yes to this option, support will be included for the Intel
	  PIIX4 family of mainboard I2C interfaces.  Specifically, the following
	  versions of the chipset are supported:
	    Intel PIIX4
	    Intel 440MX
	    Serverworks OSB4
	    Serverworks CSB5
	    Serverworks CSB6
	    SMSC Victory66

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-piix4.

config I2C_PROSAVAGE
	tristate "S3/VIA (Pro)Savage"
	depends on I2C && PCI && EXPERIMENTAL
	select I2C_ALGOBIT
	help
	  If you say yes to this option, support will be included for the
	  I2C bus and DDC bus of the S3VIA embedded Savage4 and ProSavage8
	  graphics processors.
	  chipsets supported:
	    S3/VIA KM266/VT8375 aka ProSavage8
	    S3/VIA KM133/VT8365 aka Savage4

	  This support is also available as a module.  If so, the module 
	  will be called i2c-prosavage.

config I2C_RPXLITE
	tristate "Embedded Planet RPX Lite/Classic support"
	depends on (RPXLITE || RPXCLASSIC) && I2C
	select I2C_ALGO8XX

config I2C_SAVAGE4
	tristate "S3 Savage 4"
	depends on I2C && PCI && EXPERIMENTAL
	select I2C_ALGOBIT
	help
	  If you say yes to this option, support will be included for the 
	  S3 Savage 4 I2C interface.

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-savage4.

config SCx200_I2C
	tristate "NatSemi SCx200 I2C using GPIO pins"
	depends on SCx200_GPIO && I2C
	select I2C_ALGOBIT
	help
	  Enable the use of two GPIO pins of a SCx200 processor as an I2C bus.

	  If you don't know what to do here, say N.

	  This support is also available as a module.  If so, the module 
	  will be called scx200_i2c.

config SCx200_I2C_SCL
	int "GPIO pin used for SCL"
	depends on SCx200_I2C
	default "12"
	help
	  Enter the GPIO pin number used for the SCL signal.  This value can
	  also be specified with a module parameter.

config SCx200_I2C_SDA
	int "GPIO pin used for SDA"
	depends on SCx200_I2C
	default "13"
	help
	  Enter the GPIO pin number used for the SSA signal.  This value can
	  also be specified with a module parameter.

config SCx200_ACB
	tristate "NatSemi SCx200 ACCESS.bus"
	depends on I2C
	help
	  Enable the use of the ACCESS.bus controllers of a SCx200 processor.

	  If you don't know what to do here, say N.

	  This support is also available as a module.  If so, the module 
	  will be called scx200_acb.

config I2C_SIS5595
	tristate "SiS 5595"
	depends on I2C && PCI && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for the 
	  SiS5595 SMBus (a subset of I2C) interface.

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-sis5595.

config I2C_SIS630
	tristate "SiS 630/730"
	depends on I2C && PCI && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for the 
	  SiS630 and SiS730 SMBus (a subset of I2C) interface.

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-sis630.

config I2C_SIS96X
	tristate "SiS 96x"
	depends on I2C && PCI && EXPERIMENTAL
	help
	  If you say yes to this option, support will be included for the SiS
	  96x SMBus (a subset of I2C) interfaces.  Specifically, the following
	  chipsets are supported:
	    645/961
	    645DX/961
	    645DX/962
	    648/961
	    650/961
	    735

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-sis96x.

config I2C_VIA
	tristate "VIA 82C586B"
	depends on I2C && PCI && EXPERIMENTAL
	select I2C_ALGOBIT
	help

	  If you say yes to this option, support will be included for the VIA
          82C586B I2C interface

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-via.

config I2C_VIAPRO
	tristate "VIA 82C596/82C686/823x"
	depends on I2C && PCI && EXPERIMENTAL
	help

	  If you say yes to this option, support will be included for the VIA
	  82C596/82C686/823x I2C interfaces.  Specifically, the following 
	  chipsets are supported:
	  82C596A/B
	  82C686A/B
	  8231
	  8233
	  8233A
	  8235
	  8237

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-viapro.

config I2C_VOODOO3
	tristate "Voodoo 3"
	depends on I2C && PCI && EXPERIMENTAL
	select I2C_ALGOBIT
	help

	  If you say yes to this option, support will be included for the
	  Voodoo 3 I2C interface.

	  This driver can also be built as a module.  If so, the module
	  will be called i2c-voodoo3.

endmenu