xmac_ii.h

优龙2410linux2.6.8内核源代码

#define PHY_L_LC_LEDR		(3<<12)	/* Bit 13..12:	Rx/Blink/On/Off */
#define PHY_L_LC_LEDT		(3<<10)	/* Bit 11..10:	Tx/Blink/On/Off */
#define PHY_L_LC_LEDG		(3<<8)	/* Bit  9..8:	Giga/Blink/On/Off */
#define PHY_L_LC_LEDS		(3<<6)	/* Bit  7..6:	10-100/Blink/On/Off */
#define PHY_L_LC_LEDL		(3<<4)	/* Bit  5..4:	Link/Blink/On/Off */
#define PHY_L_LC_LEDF		(3<<2)	/* Bit  3..2:	Duplex/Blink/On/Off */
#define PHY_L_LC_PSTRECH	(1<<1)	/* Bit  1:	Strech LED Pulses */
#define PHY_L_LC_FREQ		(1<<0)	/* Bit  0:	30/100 ms */

/*****  PHY_LONE_PORT_CTRL	16 bit r/w	Port Control Reg *****/
#define PHY_L_PC_TX_TCLK	(1<<15)	/* Bit 15:	Enable TX_TCLK */
									/* Bit 14:	reserved */
#define PHY_L_PC_ALT_NP		(1<<13)	/* Bit 14:	Alternate Next Page */
#define PHY_L_PC_GMII_ALT	(1<<12)	/* Bit 13:	Alternate GMII driver */
									/* Bit 11:	reserved */
#define PHY_L_PC_TEN_CRS	(1<<10)	/* Bit 10:	Extend CRS*/
									/* Bit  9..0:	not described */

/*****  PHY_LONE_CIM		16 bit r/o	CIM Reg *****/
#define PHY_L_CIM_ISOL		(255<<8)/* Bit 15..8:	Isolate Count */
#define PHY_L_CIM_FALSE_CAR	(255<<0)/* Bit  7..0:	False Carrier Count */


/*
 * Pause Bits (PHY_L_AN_ASP and PHY_L_AN_PC) encoding
 */
#define PHY_L_P_NO_PAUSE	(0<<10)	/* Bit 11..10:	no Pause Mode */
#define PHY_L_P_SYM_MD		(1<<10)	/* Bit 11..10:	symmetric Pause Mode */
#define PHY_L_P_ASYM_MD		(2<<10)	/* Bit 11..10:	asymmetric Pause Mode */
#define PHY_L_P_BOTH_MD		(3<<10)	/* Bit 11..10:	both Pause Mode */


/*
 * National-Specific
 */
/*****  PHY_NAT_1000T_CTRL	16 bit r/w	1000Base-T Control Reg *****/
#define PHY_N_1000C_TEST	(7<<13)	/* Bit 15..13:	Test Modes */
#define PHY_N_1000C_MSE		(1<<12)	/* Bit 12:	Master/Slave Enable */
#define PHY_N_1000C_MSC		(1<<11)	/* Bit 11:	M/S Configuration */
#define PHY_N_1000C_RD		(1<<10)	/* Bit 10:	Repeater/DTE */
#define PHY_N_1000C_AFD		(1<<9)	/* Bit  9:	Advertise Full Duplex */
#define PHY_N_1000C_AHD		(1<<8)	/* Bit  8:	Advertise Half Duplex */
#define PHY_N_1000C_APC		(1<<7)	/* Bit  7:	Asymmetric Pause Cap. */
									/* Bit  6..0:	reserved */

/*****  PHY_NAT_1000T_STAT	16 bit r/o	1000Base-T Status Reg *****/
#define PHY_N_1000S_MSF		(1<<15)	/* Bit 15:	Master/Slave Fault */
#define PHY_N_1000S_MSR		(1<<14)	/* Bit 14:	Master/Slave Result */
#define PHY_N_1000S_LRS		(1<<13)	/* Bit 13:	Local Receiver Status */
#define PHY_N_1000S_RRS		(1<<12)	/* Bit 12:	Remote Receiver Status*/
#define PHY_N_1000S_LP_FD	(1<<11)	/* Bit 11:	Link Partner can FD */
#define PHY_N_1000S_LP_HD	(1<<10)	/* Bit 10:	Link Partner can HD */
#define PHY_N_1000C_LP_APC	(1<<9)	/* Bit  9:	LP Asym. Pause Cap. */
									/* Bit  8:	reserved */
#define PHY_N_1000S_IEC		0xff	/* Bit  7..0:	Idle Error Count */

/*****  PHY_NAT_EXT_STAT	16 bit r/o	Extended Status Register *****/
#define PHY_N_ES_X_FD_CAP	(1<<15)	/* Bit 15:	1000Base-X FD capable */
#define PHY_N_ES_X_HD_CAP	(1<<14)	/* Bit 14:	1000Base-X HD capable */
#define PHY_N_ES_T_FD_CAP	(1<<13)	/* Bit 13:	1000Base-T FD capable */
#define PHY_N_ES_T_HD_CAP	(1<<12)	/* Bit 12:	1000Base-T HD capable */
									/* Bit 11..0:	reserved */

/* todo: those are still missing */
/*****  PHY_NAT_EXT_CTRL1	16 bit r/o	Extended Control Reg1 *****/
/*****  PHY_NAT_Q_STAT1		16 bit r/o	Quick Status Reg1 *****/
/*****  PHY_NAT_10B_OP		16 bit r/o	10Base-T Operations Reg *****/
/*****  PHY_NAT_EXT_CTRL2	16 bit r/o	Extended Control Reg1 *****/
/*****  PHY_NAT_Q_STAT2		16 bit r/o	Quick Status Reg2 *****/
/*****  PHY_NAT_PHY_ADDR	16 bit r/o	PHY Address Register *****/

/*
 * Marvell-Specific
 */
/*****  PHY_MARV_AUNE_ADV	16 bit r/w	Auto-Negotiation Advertisement *****/
/*****  PHY_MARV_AUNE_LP	16 bit r/w	Link Part Ability Reg *****/
#define PHY_M_AN_NXT_PG		BIT_15	/* Request Next Page */
#define PHY_M_AN_ACK		BIT_14	/* (ro)	Acknowledge Received */
#define PHY_M_AN_RF			BIT_13	/* Remote Fault */
									/* Bit 12:	reserved */
#define PHY_M_AN_ASP		BIT_11	/* Asymmetric Pause */
#define PHY_M_AN_PC			BIT_10	/* MAC Pause implemented */
#define PHY_M_AN_100_FD		BIT_8	/* Advertise 100Base-TX Full Duplex */
#define PHY_M_AN_100_HD		BIT_7	/* Advertise 100Base-TX Half Duplex */
#define PHY_M_AN_10_FD		BIT_6	/* Advertise 10Base-TX Full Duplex */
#define PHY_M_AN_10_HD		BIT_5	/* Advertise 10Base-TX Half Duplex */

/* special defines for FIBER (88E1011S only) */
#define PHY_M_AN_ASP_X		BIT_8	/* Asymmetric Pause */
#define PHY_M_AN_PC_X		BIT_7	/* MAC Pause implemented */
#define PHY_M_AN_1000X_AHD	BIT_6	/* Advertise 10000Base-X Half Duplex */
#define PHY_M_AN_1000X_AFD	BIT_5	/* Advertise 10000Base-X Full Duplex */

/* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */
#define PHY_M_P_NO_PAUSE_X	(0<<7)	/* Bit  8.. 7:	no Pause Mode */
#define PHY_M_P_SYM_MD_X	(1<<7)	/* Bit  8.. 7:	symmetric Pause Mode */
#define PHY_M_P_ASYM_MD_X	(2<<7)	/* Bit  8.. 7:	asymmetric Pause Mode */
#define PHY_M_P_BOTH_MD_X	(3<<7)	/* Bit  8.. 7:	both Pause Mode */

/*****  PHY_MARV_1000T_CTRL	16 bit r/w	1000Base-T Control Reg *****/
#define PHY_M_1000C_TEST	(7<<13)	/* Bit 15..13:	Test Modes */
#define PHY_M_1000C_MSE		(1<<12)	/* Bit 12:	Manual Master/Slave Enable */
#define PHY_M_1000C_MSC		(1<<11)	/* Bit 11:	M/S Configuration (1=Master) */
#define PHY_M_1000C_MPD		(1<<10)	/* Bit 10:	Multi-Port Device */
#define PHY_M_1000C_AFD		(1<<9)	/* Bit  9:	Advertise Full Duplex */
#define PHY_M_1000C_AHD		(1<<8)	/* Bit  8:	Advertise Half Duplex */
									/* Bit  7..0:	reserved */

/*****  PHY_MARV_PHY_CTRL	16 bit r/w	PHY Specific Ctrl Reg *****/
#define PHY_M_PC_TX_FFD_MSK	(3<<14)	/* Bit 15..14:	Tx FIFO Depth Mask */
#define PHY_M_PC_RX_FFD_MSK	(3<<12)	/* Bit 13..12:	Rx FIFO Depth Mask */
#define PHY_M_PC_ASS_CRS_TX	(1<<11)	/* Bit 11:	Assert CRS on Transmit */
#define PHY_M_PC_FL_GOOD	(1<<10)	/* Bit 10:	Force Link Good */
#define PHY_M_PC_EN_DET_MSK	(3<<8)	/* Bit  9.. 8:	Energy Detect Mask */
#define PHY_M_PC_ENA_EXT_D	(1<<7)	/* Bit  7:	Enable Ext. Distance (10BT) */
#define PHY_M_PC_MDIX_MSK	(3<<5)	/* Bit  6.. 5:	MDI/MDIX Config. Mask */
#define PHY_M_PC_DIS_125CLK	(1<<4)	/* Bit  4:	Disable 125 CLK */
#define PHY_M_PC_MAC_POW_UP	(1<<3)	/* Bit  3:	MAC Power up */
#define PHY_M_PC_SQE_T_ENA	(1<<2)	/* Bit  2:	SQE Test Enabled */
#define PHY_M_PC_POL_R_DIS	(1<<1)	/* Bit  1:	Polarity Reversal Disabled */
#define PHY_M_PC_DIS_JABBER	(1<<0)	/* Bit  0:	Disable Jabber */

#define PHY_M_PC_EN_DET			SHIFT8(2)	/* Energy Detect (Mode 1) */
#define PHY_M_PC_EN_DET_PLUS	SHIFT8(3)	/* Energy Detect Plus (Mode 2) */

#define PHY_M_PC_MDI_XMODE(x)	SHIFT5(x)	
#define PHY_M_PC_MAN_MDI	0    	/* 00 = Manual MDI configuration */
#define PHY_M_PC_MAN_MDIX	1		/* 01 = Manual MDIX configuration */
#define PHY_M_PC_ENA_AUTO	3		/* 11 = Enable Automatic Crossover */

/*****  PHY_MARV_PHY_STAT	16 bit r/o	PHY Specific Status Reg *****/
#define PHY_M_PS_SPEED_MSK	(3<<14)	/* Bit 15..14:	Speed Mask */
#define PHY_M_PS_SPEED_1000	(1<<15)	/*       10 = 1000 Mbps */
#define PHY_M_PS_SPEED_100	(1<<14)	/*       01 =  100 Mbps */
#define PHY_M_PS_SPEED_10	0		/*       00 =   10 Mbps */
#define PHY_M_PS_FULL_DUP	(1<<13)	/* Bit 13:	Full Duplex */
#define PHY_M_PS_PAGE_REC	(1<<12)	/* Bit 12:	Page Received */
#define PHY_M_PS_SPDUP_RES	(1<<11)	/* Bit 11:	Speed & Duplex Resolved */
#define PHY_M_PS_LINK_UP	(1<<10)	/* Bit 10:	Link Up */
#define PHY_M_PS_CABLE_MSK	(3<<7)	/* Bit  9.. 7:	Cable Length Mask */
#define PHY_M_PS_MDI_X_STAT	(1<<6)	/* Bit  6:	MDI Crossover Stat (1=MDIX) */
#define PHY_M_PS_DOWNS_STAT	(1<<5)	/* Bit  5:	Downshift Status (1=downsh.) */
#define PHY_M_PS_ENDET_STAT	(1<<4)	/* Bit  4:	Energy Detect Status (1=act) */
#define PHY_M_PS_TX_P_EN	(1<<3)	/* Bit  3:	Tx Pause Enabled */
#define PHY_M_PS_RX_P_EN	(1<<2)	/* Bit  2:	Rx Pause Enabled */
#define PHY_M_PS_POL_REV	(1<<1)	/* Bit  1:	Polarity Reversed */
#define PHY_M_PC_JABBER		(1<<0)	/* Bit  0:	Jabber */

#define PHY_M_PS_PAUSE_MSK	(PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN)

/*****  PHY_MARV_INT_MASK	16 bit r/w	Interrupt Mask Reg *****/
/*****  PHY_MARV_INT_STAT	16 bit r/o	Interrupt Status Reg *****/
#define PHY_M_IS_AN_ERROR	(1<<15)	/* Bit 15:	Auto-Negotiation Error */
#define PHY_M_IS_LSP_CHANGE	(1<<14)	/* Bit 14:	Link Speed Changed */
#define PHY_M_IS_DUP_CHANGE	(1<<13)	/* Bit 13:	Duplex Mode Changed */
#define PHY_M_IS_AN_PR		(1<<12)	/* Bit 12:	Page Received */
#define PHY_M_IS_AN_COMPL	(1<<11)	/* Bit 11:	Auto-Negotiation Completed */
#define PHY_M_IS_LST_CHANGE	(1<<10)	/* Bit 10:	Link Status Changed */
#define PHY_M_IS_SYMB_ERROR	(1<<9)	/* Bit  9:	Symbol Error */
#define PHY_M_IS_FALSE_CARR	(1<<8)	/* Bit  8:	False Carrier */
#define PHY_M_IS_FIFO_ERROR	(1<<7)	/* Bit  7:	FIFO Overflow/Underrun Error */
#define PHY_M_IS_MDI_CHANGE	(1<<6)	/* Bit  6:	MDI Crossover Changed */
#define PHY_M_IS_DOWNSH_DET	(1<<5)	/* Bit  5:	Downshift Detected */
#define PHY_M_IS_END_CHANGE	(1<<4)	/* Bit  4:	Energy Detect Changed */
									/* Bit  3..2:	reserved */
#define PHY_M_IS_POL_CHANGE	(1<<1)	/* Bit  1:	Polarity Changed */
#define PHY_M_IS_JABBER		(1<<0)	/* Bit  0:	Jabber */

#define PHY_M_DEF_MSK		(PHY_M_IS_AN_ERROR | PHY_M_IS_AN_PR | \
							PHY_M_IS_LST_CHANGE | PHY_M_IS_FIFO_ERROR)

/*****  PHY_MARV_EXT_CTRL	16 bit r/w	Ext. PHY Specific Ctrl *****/
#define PHY_M_EC_M_DSC_MSK	(3<<10)	/* Bit 11..10:	Master downshift counter */
#define PHY_M_EC_S_DSC_MSK	(3<<8)	/* Bit  9.. 8:	Slave  downshift counter */
#define PHY_M_EC_MAC_S_MSK	(7<<4)	/* Bit  6.. 4:	Def. MAC interface speed */
#define PHY_M_EC_FIB_AN_ENA	(1<<3)	/* Bit  3:	Fiber Auto-Neg. Enable */

#define PHY_M_EC_M_DSC(x)		SHIFT10(x)	/* 00=1x; 01=2x; 10=3x; 11=4x */
#define PHY_M_EC_S_DSC(x)		SHIFT8(x)	/* 00=dis; 01=1x; 10=2x; 11=3x */
#define PHY_M_EC_MAC_S(x)		SHIFT4(x)	/* 01X=0; 110=2.5; 111=25 (MHz) */

#define MAC_TX_CLK_0_MHZ	2
#define MAC_TX_CLK_2_5_MHZ	6
#define MAC_TX_CLK_25_MHZ	7

/*****  PHY_MARV_LED_CTRL	16 bit r/w	LED Control Reg *****/
#define PHY_M_LEDC_DIS_LED	(1<<15)	/* Bit 15:	Disable LED */
#define PHY_M_LEDC_PULS_MSK	(7<<12)	/* Bit 14..12:  Pulse Stretch Mask */
#define PHY_M_LEDC_F_INT	(1<<11)	/* Bit 11:	Force Interrupt */
#define PHY_M_LEDC_BL_R_MSK	(7<<8)	/* Bit 10.. 8:  Blink Rate Mask */
									/* Bit  7.. 5:	reserved */
#define PHY_M_LEDC_LINK_MSK	(3<<3)	/* Bit  4.. 3:	Link Control Mask */
#define PHY_M_LEDC_DP_CTRL	(1<<2)	/* Bit  2:	Duplex Control */
#define PHY_M_LEDC_RX_CTRL	(1<<1)	/* Bit  1:	Rx activity / Link */
#define PHY_M_LEDC_TX_CTRL	(1<<0)	/* Bit  0:	Tx activity / Link */

#define PHY_M_LED_PULS_DUR(x)	SHIFT12(x)	/* Pulse Stretch Duration */

#define	PULS_NO_STR		0		/* no pulse stretching */
#define	PULS_21MS		1		/* 21 ms to 42 ms */
#define PULS_42MS		2		/* 42 ms to 84 ms */
#define PULS_84MS		3		/* 84 ms to 170 ms */
#define PULS_170MS		4		/* 170 ms to 340 ms */
#define PULS_340MS		5		/* 340 ms to 670 ms */
#define PULS_670MS		6		/* 670 ms to 1.3 s */
#define PULS_1300MS		7		/* 1.3 s to 2.7 s */

#define PHY_M_LED_BLINK_RT(x)	SHIFT8(x)	/* Blink Rate */

#define BLINK_42MS		0		/* 42 ms */
#define BLINK_84MS		1		/* 84 ms */
#define BLINK_170MS		2		/* 170 ms */
#define BLINK_340MS		3		/* 340 ms */
#define BLINK_670MS		4		/* 670 ms */
								/* values 5 - 7: reserved */

/*****  PHY_MARV_LED_OVER	16 bit r/w	Manual LED Override Reg *****/
#define PHY_M_LED_MO_DUP(x)		SHIFT10(x)	/* Bit 11..10:  Duplex */
#define PHY_M_LED_MO_10(x)		SHIFT8(x)	/* Bit  9.. 8:  Link 10 */
#define PHY_M_LED_MO_100(x)		SHIFT6(x)	/* Bit  7.. 6:  Link 100 */
#define PHY_M_LED_MO_1000(x)	SHIFT4(x)	/* Bit  5.. 4:  Link 1000 */
#define PHY_M_LED_MO_RX(x)		SHIFT2(x)	/* Bit  3.. 2:  Rx */
#define PHY_M_LED_MO_TX(x)		SHIFT0(x)	/* Bit  1.. 0:  Tx */

#define MO_LED_NORM			0
#define MO_LED_BLINK		1
#define MO_LED_OFF			2
#define MO_LED_ON			3

/*****  PHY_MARV_EXT_CTRL_2	16 bit r/w	Ext. PHY Specific Ctrl 2 *****/
									/* Bit 15.. 7:	reserved */
#define PHY_M_EC2_FI_IMPED	(1<<6)	/* Bit  6:	Fiber Input  Impedance */
#define PHY_M_EC2_FO_IMPED	(1<<5)	/* Bit  5:	Fiber Output Impedance */
#define PHY_M_EC2_FO_M_CLK	(1<<4)	/* Bit  4:	Fiber Mode Clock Enable */
#define PHY_M_EC2_FO_BOOST	(1<<3)	/* Bit  3:	Fiber Output Boost */
#define PHY_M_EC2_FO_AM_MSK	7		/* Bit  2.. 0:	Fiber Output Amplitude */

/*****	PHY_MARV_EXT_P_STAT 16 bit r/w	Ext. PHY Specific Status *****/
#define PHY_M_FC_AUTO_SEL	(1<<15)	/* Bit 15:	Fiber/Copper Auto Sel. dis. */
#define PHY_M_FC_AN_REG_ACC (1<<14) /* Bit 14:	Fiber/Copper Autoneg. reg acc */
#define PHY_M_FC_RESULUTION (1<<13)	/* Bit 13:	Fiber/Copper Resulution */
#define PHY_M_SER_IF_AN_BP  (1<<12) /* Bit 12:	Ser IF autoneg. bypass enable */
#define PHY_M_SER_IF_BP_ST	(1<<11) /* Bit 11:	Ser IF autoneg. bypass status */
#define PHY_M_IRQ_POLARITY	(1<<10) /* Bit 10:	IRQ polarity */
									/* Bit 9..4: reserved */
#define PHY_M_UNDOC1		(1<< 7) /* undocumented bit !! */
#define PHY_M_MODE_MASK		(0xf<<0)/* Bit 3..0: copy of HWCFG MODE[3:0] */


/*****  PHY_MARV_CABLE_DIAG	16 bit r/o	Cable Diagnostic Reg *****/
#define PHY_M_CABD_ENA_TEST	(1<<15)	/* Bit 15:	Enable Test */
#define PHY_M_CABD_STAT