ftdi_sio.c

来自「优龙2410linux2.6.8内核源代码」· C语言 代码 · 共 1,815 行 · 第 1/5 页

	.unthrottle =		ftdi_unthrottle,
	.write =		ftdi_write,
	.write_room =		ftdi_write_room,
	.chars_in_buffer =	ftdi_chars_in_buffer,
	.read_bulk_callback =	ftdi_read_bulk_callback,
	.write_bulk_callback =	ftdi_write_bulk_callback,
	.tiocmget =             ftdi_tiocmget,
	.tiocmset =             ftdi_tiocmset,
	.ioctl =		ftdi_ioctl,
	.set_termios =		ftdi_set_termios,
	.break_ctl =		ftdi_break_ctl,
	.attach =		ftdi_FT232BM_startup,
	.shutdown =		ftdi_shutdown,
};

static struct usb_serial_device_type ftdi_USB_UIRT_device = {
	.owner =		THIS_MODULE,
	.name =			"USB-UIRT Infrared Tranceiver",
	.id_table =		id_table_USB_UIRT,
	.num_interrupt_in =	0,
	.num_bulk_in =		1,
	.num_bulk_out =		1,
	.num_ports =		1,
	.open =			ftdi_open,
	.close =		ftdi_close,
	.throttle =		ftdi_throttle,
	.unthrottle =		ftdi_unthrottle,
	.write =		ftdi_write,
	.write_room =		ftdi_write_room,
	.chars_in_buffer =	ftdi_chars_in_buffer,
	.read_bulk_callback =	ftdi_read_bulk_callback,
	.write_bulk_callback =	ftdi_write_bulk_callback,
	.tiocmget =             ftdi_tiocmget,
	.tiocmset =             ftdi_tiocmset,
	.ioctl =		ftdi_ioctl,
	.set_termios =		ftdi_set_termios,
	.break_ctl =		ftdi_break_ctl,
	.attach =		ftdi_USB_UIRT_startup,
	.shutdown =		ftdi_shutdown,
};

/* The TIRA1 is based on a  FT232BM which requires a fixed baud rate of 100000
 * and which requires RTS-CTS to be enabled. */
static struct usb_serial_device_type ftdi_HE_TIRA1_device = {
	.owner =		THIS_MODULE,
	.name =			"Home-Electronics TIRA-1 IR Transceiver",
	.id_table =		id_table_HE_TIRA1,
	.num_interrupt_in =	0,
	.num_bulk_in =		1,
	.num_bulk_out =		1,
	.num_ports =		1,
	.open =			ftdi_open,
	.close =		ftdi_close,
	.throttle =		ftdi_throttle,
	.unthrottle =		ftdi_unthrottle,
	.write =		ftdi_write,
	.write_room =		ftdi_write_room,
	.chars_in_buffer =	ftdi_chars_in_buffer,
	.read_bulk_callback =	ftdi_read_bulk_callback,
	.write_bulk_callback =	ftdi_write_bulk_callback,
	.tiocmget =             ftdi_tiocmget,
	.tiocmset =             ftdi_tiocmset,
	.ioctl =		ftdi_ioctl,
	.set_termios =		ftdi_set_termios,
	.break_ctl =		ftdi_break_ctl,
	.attach =		ftdi_HE_TIRA1_startup,
	.shutdown =		ftdi_shutdown,
};



#define WDR_TIMEOUT (HZ * 5 ) /* default urb timeout */

/* High and low are for DTR, RTS etc etc */
#define HIGH 1
#define LOW 0

/*
 * ***************************************************************************
 * Utlity functions
 * ***************************************************************************
 */

static unsigned short int ftdi_232am_baud_base_to_divisor(int baud, int base)
{
	unsigned short int divisor;
	int divisor3 = base / 2 / baud; // divisor shifted 3 bits to the left
	if ((divisor3 & 0x7) == 7) divisor3 ++; // round x.7/8 up to x+1
	divisor = divisor3 >> 3;
	divisor3 &= 0x7;
	if (divisor3 == 1) divisor |= 0xc000; else // 0.125
	if (divisor3 >= 4) divisor |= 0x4000; else // 0.5
	if (divisor3 != 0) divisor |= 0x8000;      // 0.25
	if (divisor == 1) divisor = 0;	/* special case for maximum baud rate */
	return divisor;
}

static unsigned short int ftdi_232am_baud_to_divisor(int baud)
{
	 return(ftdi_232am_baud_base_to_divisor(baud, 48000000));
}

static __u32 ftdi_232bm_baud_base_to_divisor(int baud, int base)
{
	static const unsigned char divfrac[8] = { 0, 3, 2, 4, 1, 5, 6, 7 };
	__u32 divisor;
	int divisor3 = base / 2 / baud; // divisor shifted 3 bits to the left
	divisor = divisor3 >> 3;
	divisor |= (__u32)divfrac[divisor3 & 0x7] << 14;
	/* Deal with special cases for highest baud rates. */
	if (divisor == 1) divisor = 0; else	// 1.0
	if (divisor == 0x4001) divisor = 1;	// 1.5
	return divisor;
}

static __u32 ftdi_232bm_baud_to_divisor(int baud)
{
	 return(ftdi_232bm_baud_base_to_divisor(baud, 48000000));
}

static int set_rts(struct usb_serial_port *port, int high_or_low)
{
	struct ftdi_private *priv = usb_get_serial_port_data(port);
	char *buf;
	unsigned ftdi_high_or_low;
	int rv;
	
	buf = kmalloc(1, GFP_NOIO);
	if (!buf)
		return -ENOMEM;
	
	if (high_or_low) {
		ftdi_high_or_low = FTDI_SIO_SET_RTS_HIGH;
		priv->last_dtr_rts |= TIOCM_RTS;
	} else {
		ftdi_high_or_low = FTDI_SIO_SET_RTS_LOW;
		priv->last_dtr_rts &= ~TIOCM_RTS;
	}
	rv = usb_control_msg(port->serial->dev,
			       usb_sndctrlpipe(port->serial->dev, 0),
			       FTDI_SIO_SET_MODEM_CTRL_REQUEST, 
			       FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE,
			       ftdi_high_or_low, 0, 
			       buf, 0, WDR_TIMEOUT);

	kfree(buf);
	return rv;
}


static int set_dtr(struct usb_serial_port *port, int high_or_low)
{
	struct ftdi_private *priv = usb_get_serial_port_data(port);
	char *buf;
	unsigned ftdi_high_or_low;
	int rv;
	
	buf = kmalloc(1, GFP_NOIO);
	if (!buf)
		return -ENOMEM;

	if (high_or_low) {
		ftdi_high_or_low = FTDI_SIO_SET_DTR_HIGH;
		priv->last_dtr_rts |= TIOCM_DTR;
	} else {
		ftdi_high_or_low = FTDI_SIO_SET_DTR_LOW;
		priv->last_dtr_rts &= ~TIOCM_DTR;
	}
	rv = usb_control_msg(port->serial->dev,
			       usb_sndctrlpipe(port->serial->dev, 0),
			       FTDI_SIO_SET_MODEM_CTRL_REQUEST, 
			       FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE,
			       ftdi_high_or_low, 0, 
			       buf, 0, WDR_TIMEOUT);

	kfree(buf);
	return rv;
}


static __u32 get_ftdi_divisor(struct usb_serial_port * port);


static int change_speed(struct usb_serial_port *port)
{
	char *buf;
        __u16 urb_value;
	__u16 urb_index;
	__u32 urb_index_value;
	int rv;

	buf = kmalloc(1, GFP_NOIO);
	if (!buf)
		return -ENOMEM;

	urb_index_value = get_ftdi_divisor(port);
	urb_value = (__u16)urb_index_value;
	urb_index = (__u16)(urb_index_value >> 16);
	
	rv = usb_control_msg(port->serial->dev,
			    usb_sndctrlpipe(port->serial->dev, 0),
			    FTDI_SIO_SET_BAUDRATE_REQUEST,
			    FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE,
			    urb_value, urb_index,
			    buf, 0, 100);

	kfree(buf);
	return rv;
}


static __u32 get_ftdi_divisor(struct usb_serial_port * port)
{ /* get_ftdi_divisor */
	struct ftdi_private *priv = usb_get_serial_port_data(port);
	__u32 div_value = 0;
	int div_okay = 1;
	char *chip_name = "";
	int baud;

	/*
	 * The logic involved in setting the baudrate can be cleanly split in 3 steps.
	 * Obtaining the actual baud rate is a little tricky since unix traditionally
	 * somehow ignored the possibility to set non-standard baud rates.
	 * 1. Standard baud rates are set in tty->termios->c_cflag
	 * 2. If these are not enough, you can set any speed using alt_speed as follows:
	 *    - set tty->termios->c_cflag speed to B38400
	 *    - set your real speed in tty->alt_speed; it gets ignored when
	 *      alt_speed==0, (or)
	 *    - call TIOCSSERIAL ioctl with (struct serial_struct) set as follows:
	 *      flags & ASYNC_SPD_MASK == ASYNC_SPD_[HI, VHI, SHI, WARP], this just
	 *      sets alt_speed to (HI: 57600, VHI: 115200, SHI: 230400, WARP: 460800)
	 * ** Steps 1, 2 are done courtesy of tty_get_baud_rate
	 * 3. You can also set baud rate by setting custom divisor as follows
	 *    - set tty->termios->c_cflag speed to B38400
	 *    - call TIOCSSERIAL ioctl with (struct serial_struct) set as follows:
	 *      o flags & ASYNC_SPD_MASK == ASYNC_SPD_CUST
	 *      o custom_divisor set to baud_base / your_new_baudrate
	 * ** Step 3 is done courtesy of code borrowed from serial.c - I should really
	 *    spend some time and separate+move this common code to serial.c, it is
	 *    replicated in nearly every serial driver you see.
	 */

	/* 1. Get the baud rate from the tty settings, this observes alt_speed hack */

	baud = tty_get_baud_rate(port->tty);
	dbg("%s - tty_get_baud_rate reports speed %d", __FUNCTION__, baud);

	/* 2. Observe async-compatible custom_divisor hack, update baudrate if needed */

	if (baud == 38400 &&
	    ((priv->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) &&
	     (priv->custom_divisor)) {
		baud = priv->baud_base / priv->custom_divisor;
		dbg("%s - custom divisor %d sets baud rate to %d", __FUNCTION__, priv->custom_divisor, baud);
	}

	/* 3. Convert baudrate to device-specific divisor */

	if (!baud) baud = 9600;	
	switch(priv->chip_type) {
	case SIO: /* SIO chip */
		chip_name = "SIO";
		switch(baud) {
		case 300: div_value = ftdi_sio_b300; break;
		case 600: div_value = ftdi_sio_b600; break;
		case 1200: div_value = ftdi_sio_b1200; break;
		case 2400: div_value = ftdi_sio_b2400; break;
		case 4800: div_value = ftdi_sio_b4800; break;
		case 9600: div_value = ftdi_sio_b9600; break;
		case 19200: div_value = ftdi_sio_b19200; break;
		case 38400: div_value = ftdi_sio_b38400; break;
		case 57600: div_value = ftdi_sio_b57600;  break;
		case 115200: div_value = ftdi_sio_b115200; break;
		} /* baud */
		if (div_value == 0) {
  			dbg("%s - Baudrate (%d) requested is not supported", __FUNCTION__,  baud);
			div_value = ftdi_sio_b9600;
			div_okay = 0;
		}
		break;
	case FT8U232AM: /* 8U232AM chip */
		chip_name = "FT8U232AM";
		if (baud <= 3000000) {
			div_value = ftdi_232am_baud_to_divisor(baud);
		} else {
	                dbg("%s - Baud rate too high!", __FUNCTION__);
			div_value = ftdi_232am_baud_to_divisor(9600);
			div_okay = 0;
		}
		break;
	case FT232BM: /* FT232BM chip */
		chip_name = "FT232BM";
		if (baud <= 3000000) {
			div_value = ftdi_232bm_baud_to_divisor(baud);
		} else {
	                dbg("%s - Baud rate too high!", __FUNCTION__);
			div_value = ftdi_232bm_baud_to_divisor(9600);
			div_okay = 0;
		}
		break;
	} /* priv->chip_type */

	if (div_okay) {
		dbg("%s - Baud rate set to %d (divisor 0x%lX) on chip %s",
			__FUNCTION__, baud, (unsigned long)div_value, chip_name);
	}

	return(div_value);
}


static int get_serial_info(struct usb_serial_port * port, struct serial_struct __user * retinfo)
{
	struct ftdi_private *priv = usb_get_serial_port_data(port);
	struct serial_struct tmp;

	if (!retinfo)
		return -EFAULT;
	memset(&tmp, 0, sizeof(tmp));
	tmp.flags = priv->flags;
	tmp.baud_base = priv->baud_base;
	tmp.custom_divisor = priv->custom_divisor;
	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
		return -EFAULT;
	return 0;
} /* get_serial_info */


static int set_serial_info(struct usb_serial_port * port, struct serial_struct __user * newinfo)
{ /* set_serial_info */
	struct ftdi_private *priv = usb_get_serial_port_data(port);
	struct serial_struct new_serial;
	struct ftdi_private old_priv;

	if (copy_from_user(&new_serial, newinfo, sizeof(new_serial)))
		return -EFAULT;
	old_priv = * priv;

	/* Do error checking and permission checking */

	if (!capable(CAP_SYS_ADMIN)) {
		if (((new_serial.flags & ~ASYNC_USR_MASK) !=
		     (priv->flags & ~ASYNC_USR_MASK)))
			return -EPERM;
		priv->flags = ((priv->flags & ~ASYNC_USR_MASK) |
			       (new_serial.flags & ASYNC_USR_MASK));
		priv->custom_divisor = new_serial.custom_divisor;
		goto check_and_exit;
	}

	if ((new_serial.baud_base != priv->baud_base) ||
	    (new_serial.baud_base < 9600))
		return -EINVAL;

	/* Make the changes - these are privileged changes! */

	priv->flags = ((priv->flags & ~ASYNC_FLAGS) |
	               (new_serial.flags & ASYNC_FLAGS));	
	priv->custom_divisor = new_serial.custom_divisor;

	port->tty->low_latency = (priv->flags & ASYNC_LOW_LATENCY) ? 1 : 0;

check_and_exit: