📄 hc_sl811.h
字号:
/*
* SL811HS HCD (Host Controller Driver) for USB.
*
* COPYRIGHT (C) by CYPRESS SEMICONDUCTOR INC
*
*
*/
#define GET_FRAME_NUMBER(hci) READ_REG32 (hci, HcFmNumber)
/*
* Maximum number of root hub ports.
*/
#define MAX_ROOT_PORTS 15 /* maximum OHCI root hub ports */
/* control and status registers */
#define HcRevision 0x00
#define HcControl 0x01
#define HcCommandStatus 0x02
#define HcInterruptStatus 0x03
#define HcInterruptEnable 0x04
#define HcInterruptDisable 0x05
#define HcFmInterval 0x0D
#define HcFmRemaining 0x0E
#define HcFmNumber 0x0F
#define HcLSThreshold 0x11
#define HcRhDescriptorA 0x12
#define HcRhDescriptorB 0x13
#define HcRhStatus 0x14
#define HcRhPortStatus 0x15
#define HcHardwareConfiguration 0x20
#define HcDMAConfiguration 0x21
#define HcTransferCounter 0x22
#define HcuPInterrupt 0x24
#define HcuPInterruptEnable 0x25
#define HcChipID 0x27
#define HcScratch 0x28
#define HcSoftwareReset 0x29
#define HcITLBufferLength 0x2A
#define HcATLBufferLength 0x2B
#define HcBufferStatus 0x2C
#define HcReadBackITL0Length 0x2D
#define HcReadBackITL1Length 0x2E
#define HcITLBufferPort 0x40
#define HcATLBufferPort 0x41
/* OHCI CONTROL AND STATUS REGISTER MASKS */
/*
* HcControl (control) register masks
*/
#define OHCI_CTRL_HCFS (3 << 6) /* BUS state mask */
#define OHCI_CTRL_RWC (1 << 9) /* remote wakeup connected */
#define OHCI_CTRL_RWE (1 << 10) /* remote wakeup enable */
/* pre-shifted values for HCFS */
#define OHCI_USB_RESET (0 << 6)
#define OHCI_USB_RESUME (1 << 6)
#define OHCI_USB_OPER (2 << 6)
#define OHCI_USB_SUSPEND (3 << 6)
/*
* HcCommandStatus (cmdstatus) register masks
*/
#define OHCI_HCR (1 << 0) /* host controller reset */
#define OHCI_SOC (3 << 16) /* scheduling overrun count */
/*
* masks used with interrupt registers:
* HcInterruptStatus (intrstatus)
* HcInterruptEnable (intrenable)
* HcInterruptDisable (intrdisable)
*/
#define OHCI_INTR_SO (1 << 0) /* scheduling overrun */
#define OHCI_INTR_SF (1 << 2) /* start frame */
#define OHCI_INTR_RD (1 << 3) /* resume detect */
#define OHCI_INTR_UE (1 << 4) /* unrecoverable error */
#define OHCI_INTR_FNO (1 << 5) /* frame number overflow */
#define OHCI_INTR_RHSC (1 << 6) /* root hub status change */
#define OHCI_INTR_ATD (1 << 7) /* scheduling overrun */
#define OHCI_INTR_MIE (1 << 31) /* master interrupt enable */
/*
* HcHardwareConfiguration
*/
#define InterruptPinEnable (1 << 0)
#define InterruptPinTrigger (1 << 1)
#define InterruptOutputPolarity (1 << 2)
#define DataBusWidth16 (1 << 3)
#define DREQOutputPolarity (1 << 5)
#define DACKInputPolarity (1 << 6)
#define EOTInputPolarity (1 << 7)
#define DACKMode (1 << 8)
#define AnalogOCEnable (1 << 10)
#define SuspendClkNotStop (1 << 11)
#define DownstreamPort15KRSel (1 << 12)
/*
* HcDMAConfiguration
*/
#define DMAReadWriteSelect (1 << 0)
#define ITL_ATL_DataSelect (1 << 1)
#define DMACounterSelect (1 << 2)
#define DMAEnable (1 << 4)
#define BurstLen_1 0
#define BurstLen_4 (1 << 5)
#define BurstLen_8 (2 << 5)
/*
* HcuPInterrupt
*/
#define SOFITLInt (1 << 0)
#define ATLInt (1 << 1)
#define AllEOTInterrupt (1 << 2)
#define OPR_Reg (1 << 4)
#define HCSuspended (1 << 5)
#define ClkReady (1 << 6)
/*
* HcBufferStatus
*/
#define ITL0BufferFull (1 << 0)
#define ITL1BufferFull (1 << 1)
#define ATLBufferFull (1 << 2)
#define ITL0BufferDone (1 << 3)
#define ITL1BufferDone (1 << 4)
#define ATLBufferDone (1 << 5)
/* OHCI ROOT HUB REGISTER MASKS */
/* roothub.portstatus [i] bits */
#define RH_PS_CCS 0x00000001 /* current connect status */
#define RH_PS_PES 0x00000002 /* port enable status*/
#define RH_PS_PSS 0x00000004 /* port suspend status */
#define RH_PS_POCI 0x00000008 /* port over current indicator */
#define RH_PS_PRS 0x00000010 /* port reset status */
#define RH_PS_PPS 0x00000100 /* port power status */
#define RH_PS_LSDA 0x00000200 /* low speed device attached */
#define RH_PS_CSC 0x00010000 /* connect status change */
#define RH_PS_PESC 0x00020000 /* port enable status change */
#define RH_PS_PSSC 0x00040000 /* port suspend status change */
#define RH_PS_OCIC 0x00080000 /* over current indicator change */
#define RH_PS_PRSC 0x00100000 /* port reset status change */
/* roothub.status bits */
#define RH_HS_LPS 0x00000001 /* local power status */
#define RH_HS_OCI 0x00000002 /* over current indicator */
#define RH_HS_DRWE 0x00008000 /* device remote wakeup enable */
#define RH_HS_LPSC 0x00010000 /* local power status change */
#define RH_HS_OCIC 0x00020000 /* over current indicator change */
#define RH_HS_CRWE 0x80000000 /* clear remote wakeup enable */
/* roothub.b masks */
#define RH_B_DR 0x0000ffff /* device removable flags */
#define RH_B_PPCM 0xffff0000 /* port power control mask */
/* roothub.a masks */
#define RH_A_NDP (0xff << 0) /* number of downstream ports */
#define RH_A_PSM (1 << 8) /* power switching mode */
#define RH_A_NPS (1 << 9) /* no power switching */
#define RH_A_DT (1 << 10) /* device type (mbz) */
#define RH_A_OCPM (1 << 11) /* over current protection mode */
#define RH_A_NOCP (1 << 12) /* no over current protection */
#define RH_A_POTPGT (0xff << 24) /* power on to power good time */
#define min(a,b) (((a)<(b))?(a):(b))
#define URB_DEL 1
#define PORT_STAT_DEFAULT 0x0100
#define PORT_CONNECT_STAT 0x1
#define PORT_ENABLE_STAT 0x2
#define PORT_SUSPEND_STAT 0x4
#define PORT_OVER_CURRENT_STAT 0x8
#define PORT_RESET_STAT 0x10
#define PORT_POWER_STAT 0x100
#define PORT_LOW_SPEED_DEV_ATTACH_STAT 0x200
#define PORT_CHANGE_DEFAULT 0x0
#define PORT_CONNECT_CHANGE 0x1
#define PORT_ENABLE_CHANGE 0x2
#define PORT_SUSPEND_CHANGE 0x4
#define PORT_OVER_CURRENT_CHANGE 0x8
#define PORT_RESET_CHANGE 0x10
/* Port Status Request info */
typedef struct portstat {
__u16 portChange;
__u16 portStatus;
} portstat_t;
typedef struct hcipriv {
int irq;
int disabled; /* e.g. got a UE, we're hung */
atomic_t resume_count; /* defending against multiple resumes */
struct ohci_regs * regs; /* OHCI controller's memory */
int hcport; /* I/O base address */
int hcport2; /* I/O data reg addr */
struct portstat * RHportStatus; /* root hub port status */
int intrstatus;
__u32 hc_control; /* copy of the hc control reg */
int frame;
__u8 * tl;
int xferPktLen;
int atl_len;
int atl_buffer_len;
int itl0_len;
int itl1_len;
int itl_buffer_len;
int itl_index;
int tl_last;
int units_left;
} hcipriv_t;
struct hci;
#define cClt 0 // Control
#define cISO 1 // ISO
#define cBULK 2 // BULK
#define cInt 3 // Interrupt
#define ISO_BIT 0x10
/*-------------------------------------------------------------------------
* EP0 use for configuration and Vendor Specific command interface
*------------------------------------------------------------------------*/
#define cMemStart 0x10
#define EP0Buf 0x40 /* SL11H/SL811H memory start at 0x40 */
#define EP0Len 0x40 /* Length of config buffer EP0Buf */
#define EP1Buf 0x60
#define EP1Len 0x40
/*-------------------------------------------------------------------------
* SL11H/SL811H memory from 80h-ffh use as ping-pong buffer.
*------------------------------------------------------------------------*/
#define uBufA 0x80 /* buffer A address for DATA0 */
#define uBufB 0xc0 /* buffer B address for DATA1 */
#define uXferLen 0x40 /* xfer length */
#define sMemSize 0xc0 /* Total SL11 memory size */
#define cMemEnd 256
/*-------------------------------------------------------------------------
* SL811H Register Control memory map
* --Note:
* --SL11H only has one control register set from 0x00-0x04
* --SL811H has two control register set from 0x00-0x04 and 0x08-0x0c
*------------------------------------------------------------------------*/
#define EP0Control 0x00
#define EP0Address 0x01
#define EP0XferLen 0x02
#define EP0Status 0x03
#define EP0Counter 0x04
#define EP1Control 0x08
#define EP1Address 0x09
#define EP1XferLen 0x0a
#define EP1Status 0x0b
#define EP1Counter 0x0c
#define CtrlReg 0x05
#define IntEna 0x06
// 0x07 is reserved
#define IntStatus 0x0d
#define cDATASet 0x0e
#define cSOFcnt 0x0f
#define IntMask 0x57 /* Reset|DMA|EP0|EP2|EP1 for IntEna */
#define HostMask 0x47 /* Host request command for IntStatus */
#define ReadMask 0xd7 /* Read mask interrupt for IntStatus */
/*-------------------------------------------------------------------------
* Standard Chapter 9 definition
*-------------------------------------------------------------------------
*/
#define GET_STATUS 0x00
#define CLEAR_FEATURE 0x01
#define SET_FEATURE 0x03
#define SET_ADDRESS 0x05
#define GET_DESCRIPTOR 0x06
#define SET_DESCRIPTOR 0x07
#define GET_CONFIG 0x08
#define SET_CONFIG 0x09
#define GET_INTERFACE 0x0a
#define SET_INTERFACE 0x0b
#define SYNCH_FRAME 0x0c
#define DEVICE 0x01
#define CONFIGURATION 0x02
#define STRING 0x03
#define INTERFACE 0x04
#define ENDPOINT 0x05
/*-------------------------------------------------------------------------
* SL11H/SL811H definition
*-------------------------------------------------------------------------
*/
#define DATA0_WR 0x07 // (Arm+Enable+tranmist to Host+DATA0)
#define DATA1_WR 0x47 // (Arm+Enable+tranmist to Host on DATA1)
#define ZDATA0_WR 0x05 // (Arm+Transaction Ignored+tranmist to Host+DATA0)
#define ZDATA1_WR 0x45 // (Arm+Transaction Ignored+tranmist to Host+DATA1)
#define DATA0_RD 0x03 // (Arm+Enable+received from Host+DATA0)
#define DATA1_RD 0x43 // (Arm+Enable+received from Host+DATA1)
#define PID_SETUP 0x2d // USB Specification 1.1 Standard Definition
#define PID_SOF 0xA5
#define PID_IN 0x69
#define PID_OUT 0xe1
#define MAX_RETRY 0xffff
#define TIMEOUT 5 /* 2 mseconds */
#define SL11H_HOSTCTLREG 0
#define SL11H_BUFADDRREG 1
#define SL11H_BUFLNTHREG 2
#define SL11H_PKTSTATREG 3 /* read */
#define SL11H_PIDEPREG 3 /* write */
#define SL11H_XFERCNTREG 4 /* read */
#define SL11H_DEVADDRREG 4 /* write */
#define SL11H_CTLREG1 5
#define SL11H_INTENBLREG 6
#define SL11H_HOSTCTLREG_B 8
#define SL11H_BUFADDRREG_B 9
#define SL11H_BUFLNTHREG_B 0x0A
#define SL11H_PKTSTATREG_B 0x0B /* read */
#define SL11H_PIDEPREG_B 0x0B /* write */
#define SL11H_XFERCNTREG_B 0x0C /* read */
#define SL11H_DEVADDRREG_B 0x0C /* write */
#define SL11H_INTSTATREG 0x0D /* write clears bitwise */
#define SL11H_HWREVREG 0x0E /* read */
#define SL11H_SOFLOWREG 0x0E /* write */
#define SL11H_SOFTMRREG 0x0F /* read */
#define SL11H_CTLREG2 0x0F /* write */
#define SL11H_DATA_START 0x10
/* Host control register bits (addr 0) */
#define SL11H_HCTLMASK_ARM 1
#define SL11H_HCTLMASK_ENBLEP 2
#define SL11H_HCTLMASK_WRITE 4
#define SL11H_HCTLMASK_ISOCH 0x10
#define SL11H_HCTLMASK_AFTERSOF 0x20
#define SL11H_HCTLMASK_SEQ 0x40
#define SL11H_HCTLMASK_PREAMBLE 0x80
/* Packet status register bits (addr 3) */
#define SL11H_STATMASK_ACK 1
#define SL11H_STATMASK_ERROR 2
#define SL11H_STATMASK_TMOUT 4
#define SL11H_STATMASK_SEQ 8
#define SL11H_STATMASK_SETUP 0x10
#define SL11H_STATMASK_OVF 0x20
#define SL11H_STATMASK_NAK 0x40
#define SL11H_STATMASK_STALL 0x80
/* Control register 1 bits (addr 5) */
#define SL11H_CTL1MASK_DSBLSOF 1
#define SL11H_CTL1MASK_NOTXEOF2 4
#define SL11H_CTL1MASK_DSTATE 0x18
#define SL11H_CTL1MASK_NSPD 0x20
#define SL11H_CTL1MASK_SUSPEND 0x40
#define SL11H_CTL1MASK_CLK12 0x80
#define SL11H_CTL1VAL_RESET 8
/* Interrut enable (addr 6) and interrupt status register bits (addr 0xD) */
#define SL11H_INTMASK_XFERDONE 1
#define SL11H_INTMASK_SOFINTR 0x10
#define SL11H_INTMASK_INSRMV 0x20
#define SL11H_INTMASK_USBRESET 0x40
#define SL11H_INTMASK_DSTATE 0x80 /* only in status reg */
/* HW rev and SOF lo register bits (addr 0xE) */
#define SL11H_HWRMASK_HWREV 0xF0
/* SOF counter and control reg 2 (addr 0xF) */
#define SL11H_CTL2MASK_SOFHI 0x3F
#define SL11H_CTL2MASK_DSWAP 0x40
#define SL11H_CTL2MASK_HOSTMODE 0xae
// static inline uchar SL811Read(hci_t *hci, uchar offset);
// static inline void SL811Write(hci_t *hci, uchar offset, uchar data);
// static inline void SL811BufRead(hci_t *hci, short offset, uchar *buf, short size);
// static inline void SL811BufWrite(hci_t *hci, short offset, uchar *buf, short size);
/*-------------------------------------------------------------------------*/
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -