f31x_external_interrupts.c

C8051F31X的例程（包括所有外设端口的运用例程）

//-----------------------------------------------------------------------------
// F31x_External_Interrupts.c
//-----------------------------------------------------------------------------
// Copyright 2007 Silicon Laboratories, Inc.
// http://www.silabs.com
//
// Program Description:
//
// This software shows the necessary configuration to use External Interrupt 0
// (/INT0) or External Interrupt 1 (/INT1) as an interrupt source.  The code
// executes the initialization routines and then spins in an infinite while()
// loop.  If the button on P0.7 (on the target board) is pressed, then the
// edge-triggered /INT0 input on P0.0 will cause an interrupt and toggle the
// LED.
//
// Pinout:
//
// P0.0 - /INT0
// P0.1 - /INT1
//
// P0.7 - SW1 (Switch 1)
// P3.3 - LED
//
// How To Test:
//
// 1) Compile and download code to a 'F310 target board.
// 2) On the target board, connect the switch on the J3 header (P0.7_SW)
//    to P0.0 for /INT0 or P0.1 for /INT1.
// 3) Press the switch to trigger an interrupt and toggle the LED
//
// Target:         C8051F31x
// Tool chain:     Keil C51 7.50 / Keil EVAL C51
// Command Line:   None
//
//
// Release 1.0
//    -Initial Revision (SM)
//    -10 JULY 2007
//

//-----------------------------------------------------------------------------
// Include Files
//-----------------------------------------------------------------------------

#include <C8051F310.h>

//-----------------------------------------------------------------------------
// Global Constants
//-----------------------------------------------------------------------------

#define SYSCLK             245000000   // Clock speed in Hz

sbit SW1 = P0^7;                       // Push-button switch on board
sbit LED = P3^3;                       // Green LED


//-----------------------------------------------------------------------------
// Function Prototypes
//-----------------------------------------------------------------------------

void Oscillator_Init (void);           // Configure the system clock
void Port_Init (void);                 // Configure the Crossbar and GPIO
void Ext_Interrupt_Init (void);        // Configure External Interrupts (/INT0
                                       // and /INT1)

//-----------------------------------------------------------------------------
// MAIN Routine
//-----------------------------------------------------------------------------
void main (void)
{
   PCA0MD &= ~0x40;                    // Disable Watchdog timer

   Oscillator_Init();                  // Initialize the system clock
   Port_Init ();                       // Initialize crossbar and GPIO
   Ext_Interrupt_Init();               // Initialize External Interrupts

   EA = 1;

   while(1);                           // Infinite while loop waiting for
                                       // an interrupt from /INT0 or /INT1
}

//-----------------------------------------------------------------------------
// Initialization Subroutines
//-----------------------------------------------------------------------------

//-----------------------------------------------------------------------------
// Oscillator_Init
//-----------------------------------------------------------------------------
//
// Return Value : None
// Parameters   : None
//
// This routine initializes the system clock to use the precision internal
// oscillator as its clock source.
//-----------------------------------------------------------------------------
void Oscillator_Init (void)
{
   OSCICN = 0x83;                      // Set internal oscillator to run
                                       // at its maximum frequency
}

//-----------------------------------------------------------------------------
// Port_Init
//-----------------------------------------------------------------------------
//
// Return Value : None
// Parameters   : None
//
// This function configures the crossbar and GPIO ports.
//
// Pinout:
//
// P0.0 - digital	open-drain 	/INT0
// P0.1 - digital	open-drain 	/INT1
//
// P0.7 - digital	open-drain 	SW1 (Switch 1)
// P3.3 - digital	push-pull	LED2
//
//-----------------------------------------------------------------------------
void Port_Init (void)
{
   XBR1     = 0x40;                    // Enable crossbar and weak pullups

   P0SKIP   = 0x03;
   P3MDOUT  = 0x08;                    // LED is a push-pull output
}

//-----------------------------------------------------------------------------
// Ext_Interrupt_Init
//-----------------------------------------------------------------------------
//
// Return Value : None
// Parameters   : None
//
// This function configures and enables /INT0 and /INT1 (External Interrupts)
// as negative edge-triggered.
//
//-----------------------------------------------------------------------------
void Ext_Interrupt_Init (void)
{
   TCON = 0x05;                        // /INT 0 and /INT 1 are edge triggered

   IT01CF = 0x10;                      // /INT0 active low; /INT0 on P0.0;
                                       // /INT1 active low; /INT1 on P0.1

   EX0 = 1;                            // Enable /INT0 interrupts
   EX1 = 1;                            // Enable /INT1 interrupts
}

//-----------------------------------------------------------------------------
// Interrupt Service Routines
//-----------------------------------------------------------------------------

//-----------------------------------------------------------------------------
// /INT0 ISR
//-----------------------------------------------------------------------------
//
// Whenever a negative edge appears on P0.0, LED1 is toggled.
// The interrupt pending flag is automatically cleared by vectoring to the ISR
//
//-----------------------------------------------------------------------------
void INT0_ISR (void) interrupt 0
{
   LED = !LED;
}

//-----------------------------------------------------------------------------
// /INT1 ISR
//-----------------------------------------------------------------------------
//
// Whenever a negative edge appears on P0.1, LED2 is toggled.
// The interrupt pending flag is automatically cleared by vectoring to the ISR
//
//-----------------------------------------------------------------------------
void INT1_ISR (void) interrupt 2
{
   LED = !LED;
}

//-----------------------------------------------------------------------------
// End Of File
//-----------------------------------------------------------------------------