ch16_b13-2.asm

51单片机基础篇 对于有一定基础的人看看 包含书中所以的源代码

;PROGRAM NAME B13-2.ASM
MS10    EQU     9217    ;APPROXIMATELY 10ms INTERRUPR
;
INTR_CNT EQU    30H     ;CNT STORIAGE
BUFFER  EQU     31H     ;DISPLAY BUFFER
BUF_WR  EQU     32H     ;DISPLAY BUFFER
EE_ADDR EQU     33H
WAIT    EQU     34H
;
SCLK    REG     P1.7
SDA     REG     P1.6
;
SCOPE   REG     P3.3    ;CHECK BY SCOPE
BUZZER  REG     P3.4
LED     REG     P3.7
;
        ORG     0000H
        JMP     START
        ORG     0003H   ;[DISABLE]  EXTERNAL INT0 INTERRUPT
        RETI
        ORG     000BH   ;[ENABLE]  TIMER0 OVERFLOW INTERRUPT
        JMP     T0_ISR
;
        ORG     0013H
        RETI            ;[DISABLE] EXTERNAL INT1 INTERRUPT
        ORG     001BH
        RETI            ;[DISABLE] TIMER1 OVERFLOW INTERRUPT
        ORG     0023H
        RETI            ;[DISABLE] SERIAL INTERRUPT
;
        ORG     30H
START   MOV     R0,#00H
        DJNZ    R0,$    ;DELAY A WHILE
        MOV     SP,#60H
        MOV     P1,#FFH
        MOV     P3,#FFH
        MOV     INTR_CNT,#00H
        CLR     BUZZER  ;P3.4=0,BUZZER OFF
        CLR     LED     ;P3.7=0,LED OFF
        CALL    SET_TMR0
        MOV     BUF_WR,#66H ;DISPLAY DATA
        MOV     BUFFER,#99H ;DISPLAY DATA
        CALL    IIC_INIT
$LOOP
        CLR     EA
        MOV     R0,#00
        MOV     R1,#00
        MOV     B,BUF_WR
        CALL    IIC_WRITE
        SETB    EA
        CALL    DELAY
        CALL    DELAY
;
        CLR     EA
        MOV     R0,#00
        MOV     R1,#00
        SETB    SCOPE
        CALL    IIC_READ         ;RESULT IN ACC
        CLR     SCOPE
        CJNE    A,#FFH,$NEW
        MOV     A,#00H
$NEW    MOV     BUFFER,A        ;READ FROM EEPROM
        SETB    EA
        CALL    DELAY
        CALL    DELAY
;
        MOV     A,BUF_WR
        ADD     A,#01H
        DA      A
        MOV     BUF_WR,A
        SJMP    $LOOP
;
;MEM BLOCK IN R0
;ADDRESS   IN R1
;DATA      IN B
IIC_WRITE
        CALL    IIC_START
        MOV     A,R0
        ANL     A,#07H  ;MASK BIT7-BIT3
        RL      A
        ORL     A,#A0H  ;WR=TRUE(0) AS BIT0=1
        CALL    IIC_OUT ;COMMAND OUT
        CALL    IIC_ACK ;9 CLK
;
        MOV     A,R1
        CALL    IIC_OUT ;ADDR OUT
        CALL    IIC_ACK
;
        MOV     A,B
        CALL    IIC_OUT ;DATA OUT
        CALL    IIC_ACK
;
        CALL    IIC_STOP
        RET
;
IIC_OUT CLR     SCLK
        CALL    DLY
        MOV     R7,#8
$RL     RLC     A
        JC      $O1
$O0     CLR     SDA
        JMP     $NEXT
$O1     SETB    SDA
$NEXT
        CALL    DLY
        SETB    SCLK
        CALL    DLY
        CLR     SCLK
        CLR     SDA
        CALL    DLY
        DJNZ    R7,$RL
        RET
;
;MEM BLOCK IN R0
;ADDRESS   IN R1
;DATA RETURN AT ACC
;
IIC_READ
        CALL    IIC_START
        MOV     A,R0
        ANL     A,#07H  ;MASK BIT7-BIT3
        RL      A
        ORL     A,#A0H  ;RD/!WR=0 AS BIT0=1
        CALL    IIC_OUT ;COMMAND OUT(WR)
        CALL    IIC_ACK
;
        MOV     A,R1
        CALL    IIC_OUT ;ADDR OUT
        CALL    IIC_ACK
;
        CALL    IIC_START
        MOV     A,R0
        ANL     A,#07H  ;MASK BIT7-BIT3
        RL      A
        ORL     A,#A1H  ;RD=1 AS BIT0=1
        CALL    IIC_OUT ;COMMAND OUT(RD)
        CALL    IIC_ACK
;
        CALL    IIC_IN ;DATA IN
        CALL    IIC_ACK
;
        CALL    IIC_STOP
        RET
;
IIC_ACK
        SETB    SCLK
        NOP
        CLR     SCLK
        NOP
        RET
;
IIC_IN  SETB    SDA
        CLR     SCLK
        MOV     R2,#8
        MOV     R0,#00H
$SI     SETB    SCLK
        JB      SDA,$SI1
$SI0    CLR     C
        JMP     $SNX
$SI1    SETB    C
$SNX    NOP
        MOV     A,R0    ;LOW BYTE
        RLC     A
        MOV     R0,A
        CLR     SCLK
        DJNZ    R2,$SI
        MOV     A,R0
        RET
;
IIC_INIT
        SETB    SCLK
        SETB    SDA
        RET
;
IIC_START
        SETB    SCLK
        SETB    SDA
;
        CLR     SDA
        NOP
        CLR     SCLK
        NOP
        RET
;
IIC_STOP
        SETB    SCLK
        SETB    SDA
        RET
;
DLY     RET
        MOV     WAIT,#1
        DJNZ    WAIT,$
        RET
;
;
DELAY   MOV     R7,#00H
$1      MOV     R6,#00H
$2      DJNZ    R6,$2
        DJNZ    R7,$1
        RET
;
T0_ISR
        MOV     TH0,#(65536-MS10) / 256 ;RELOAD TH0
        MOV     TL0,#(65536-MS10) .MOD. 256
        PUSH    A
;
        MOV     A,BUFFER
        ANL     A,#0FH  ;GET LOW NIBBLE
        SETB    ACC.5   ;BIT5=1
        SETB    ACC.6
        SETB    ACC.7
        MOV     P1,A    ;SHOW 1 DIGIT
        MOV     R0,#30H
        DJNZ    R0,$    ;DELAY
;inter-blanking
        CLR     ACC.4
        CLR     ACC.5
        MOV     P1,A    ;ALL DIGIT BLANK
        MOV     R0,#04H
        DJNZ    R0,$    ;DELAY
;
        MOV     A,BUFFER
        ANL     A,#F0H  ;GET HIGH NIBBLE
        SWAP    A       ;SWAP A
        SETB    ACC.4   ;BIT4=1
        SETB    ACC.6
        SETB    ACC.7
        MOV     P1,A    ;SHOW ANOTHER DIGIT
        MOV     R0,#30H
        DJNZ    R0,$    ;DELAY
;
        CLR     ACC.4
        CLR     ACC.5
        MOV     P1,A    ;ALL DIGIT BLANK
;
;INTR_CNT+1
        INC     INTR_CNT
        MOV     A,INTR_CNT
        CJNE    A,#100,$T0_END
        MOV     INTR_CNT,#00H
$T0_END POP     A
        RETI
;
SET_TMR0
        MOV     A,#01H  ;TIMER MODE 1
        MOV     TMOD,A
        MOV     TH0,#(65536-MS10) / 256 ;RELOAD TH0
        MOV     TL0,#(65536-MS10) .MOD. 256
        CLR     TF0     ;CLEAR TIMER0 FLAG
        SETB    TR0     ;TIMER0 START COUNT
        SETB    ET0     ;ENABLE TIMER0 INTERRUPT
        SETB    EA      ;ENABLE SYSTEM INTERRUPT
        RET
;