sys_conf.h

wm PNE 3.3 source code, running at more than vxworks6.x version.

/* if this will be the FIRST system to use the SMNI on this board.  It */
/* should be 2 if this will not be the first system to use SMNI on this*/
/* board.  Usually this means that SC_NISM_LEVEL should be 1 if you    */
/* are building Boot ROMs, and 2 for a system that will be downloaded  */
/* and started using the Boot ROMs.  See the comments at the beginning */
/* of drivers/ni_smem.c for more explanation.                          */
/*---------------------------------------------------------------------*/
#define SD_NISM               NO       /* Disable/Enable Shared Mem NI */
#define SD_NISM_IP            0x00000000    /* IP address of this node */
#define SD_NISM_DIRADDR       0x00000400 /* Bus addr of SMNI directory */
#define SC_NISM_BUFFS         30            /* Num of buffers for SMNI */
#define SC_NISM_LEVEL         2         /* SMNI Level, 1 if first node */
#define SD_NISM_SUBNET_MASK   0x00000000 /* Subnet mask for the SMNI   */


/*---------------------------------------------------------------------*/
/* If you want to build a multi-node pSOS+m system, set SD_KISM        */
/* to the number of nodes in the system.                               */
/*---------------------------------------------------------------------*/
#define SD_KISM               0 /* Num of nodes that will use the SMKI */
/*---------------------------------------------------------------------*/
/* Bus Address of the system-wide directory structure that all nodes   */
/* in the system have access to.                                       */
/*---------------------------------------------------------------------*/
#define SD_KISM_DIRADDR       0x00000580
#define SC_KISM_BUFFS         100           /* Num of buffers for SMKI */


/***********************************************************************/
/*                                                                     */
/*         M I S C E L L A N E O U S   N E T W O R K I N G             */
/*                       P A R A M E T E R S                           */
/*                                                                     */
/***********************************************************************/
#define SD_DEF_GTWY_IP 0x00000000


/***********************************************************************/
/* SC_RAM_SIZE define controls the end of RAM as seen by pSOSystem.    */
/* If it is set to zero, then pSOSystem uses ALL of the memory         */
/* remaining on a board for dynamic allocation ("region 0"). You may   */
/* override this by setting SC_RAM_SIZE to a non-zero value. If you do,*/
/* pSOSystem will not touch any memory after the specified address.    */
/*                                                                     */
/* NOTE: This is useful when making a BOOT ROM and you want to ensure  */
/* that the ROM's RAM area does not overflow the space allocated for it*/
/***********************************************************************/
#define SC_RAM_SIZE           0

/***********************************************************************/
/*                                                                     */
/*                     I / O   D E V I C E S                           */
/*                                                                     */
/*  Each device may be included in the system by specifying a major    */
/*  number for it, which determines its slot in the pSOS+ I/O switch   */
/*  table.  To leave a device driver out of the system, use NO for     */
/*  the major number.                                                  */
/*                                                                     */
/*  Note the following:                                                */
/*                                                                     */
/*    * Major device 0 is reserved and cannot be used for any of these */
/*      devices.  Setting a device number to 0 here is the same as NO. */
/*                                                                     */
/*    * No device number may be higher than SC_DEVMAX (SC_DEVMAX may   */
/*      be increased, if desired)                                      */
/*                                                                     */
/*    * The lines defining the symbols DEV_SERIAL, DEV_TIMER, etc,     */
/*      should not be changed.  These are for use by application       */
/*      programs as the "device number" parameter on de_* calls.       */
/*                                                                     */
/***********************************************************************/
#define SC_DEV_SERIAL         1         /* Serial driver               */
#define SC_DEV_TIMER          2         /* Periodic tick timer         */
#define SC_DEV_RAMDISK        3         /* RAM disk                    */
#define SC_DEV_CONSOLE       NO         /* PC-Console driver           */
#define SC_DEV_SCSI           5         /* SCSI bus                    */
#define SC_DEV_SCSI_TAPE      6         /* SCSI bus, tape device       */
#define SC_DEV_IDE            7         /* IDE Driver                  */
#define SC_DEV_FLOPPY         8         /* Floppy Driver               */
#define SC_DEV_NTFTP          9         /* New TFTP pseudo driver      */
#define SC_DEV_TFTP          10         /* TFTP pseudo driver          */
#define SC_DEV_HTTP          NO         /* HTTP pseudo driver          */
#define SC_DEV_SPI           NO         /* SPI driver                  */
#define SC_DEV_DLPI          NO         /* DLPI pseudo driver          */
#define SC_DEV_OTCP          NO         /* 14 TCP/IP for OpEN          */
#define SC_IP              SC_DEV_OTCP  /* 14 IP                       */
#define SC_ARP               NO         /* 15 ARP                      */
#define SC_TCP               NO         /* 16 TCP                      */
#define SC_UDP               NO         /* 17 UDP                      */
#define SC_RAW               NO         /* 18 RAW                      */
#define SC_LOOP              NO         /* 19 LOOP = (SC_DEV_OTCP + 5) */
#define SC_DEV_SOSI          NO         /* 20 OSI for OpEN             */
#define SC_DEV_PSCONSOLE     21         /* Pseudo Console driver       */
#define SC_DEV_MEMLOG        22         /* Memory log driver           */
#define SC_DEV_RDIO          23         /* pROBE+ RDIO driver          */
#define SC_DEV_NULL          24         /* Null Device Driver          */
#define SC_DEV_PARALLEL      NO         /* Parallel Port Driver        */
#define SC_DEV_CMOS          NO         /* CMOS Driver                 */
#define SC_DEV_WATCHDOG      NO         /* Watchdog Driver             */
#define SC_DEV_OLAP          NO         /* LAP Drivers                 */
#define SC_PHPI        (SC_DEV_OLAP)    /* Phpi driver                 */
#define SC_LAPB        (SC_DEV_OLAP + 0)/* LAPB driver Change 0 to 1   */
#define SC_DEV_OX25          NO         /* X25 Drivers                 */
#define SC_X25         (SC_DEV_OX25)    /* X.25 plp driver             */
#define SC_SNDCF             NO         /* sndcf driver                */
#define SC_IPCONV            NO         /* ip convergence driver       */
#define SC_DEV_ISDN          NO         /* ISDN Drivers                */
#define SC_PH          (SC_DEV_ISDN)    /* PH driver                   */
#define SC_LAPD        (SC_DEV_ISDN + 0)/* LAPD driver Change 0 to 1   */
#define SC_IPCD        (SC_DEV_ISDN + 0)/* IPCD driver Change 0 to 2   */
#define SC_DEV_MLPP          NO         /* MultiLink PPP Drivers       */
#define SC_FRMUX       (SC_DEV_MLPP)    /* FRMUX driver                */
#define SC_PPP         (SC_DEV_MLPP + 0)/* PPP  driver Change 0 to 1   */
#define SC_PIM         (SC_DEV_MLPP + 0)/* PIM  driver Change 0 to 2   */
#define SC_DEV_LOG           NO         /* STREAMS log driver          */
#define SC_DEV_PSMUX         NO         /* Sample Mux driver           */
#define SC_DEV_PSLWR         NO         /* Sample loopback driver      */
#define SC_DEV_SLLWR         NO         /* Sample loopback driver      */
#define SC_DEV_PIPE          43         /* Pipe Driver.                */

#define SC_DEVMAX            44         /* Maximum device number       */

#define DEV_SERIAL      (SC_DEV_SERIAL     << 16)
#define DEV_PARALLEL    (SC_DEV_PARALLEL   << 16)
#define DEV_TIMER       (SC_DEV_TIMER      << 16)
#define DEV_RAMDISK     (SC_DEV_RAMDISK    << 16)
#define DEV_SCSI        (SC_DEV_SCSI       << 16)
#define DEV_SCSI_TAPE   (SC_DEV_SCSI_TAPE  << 16)
#define DEV_PSCONSOLE   (SC_DEV_PSCONSOLE  << 16)
#define DEV_SYSCONSOLE  ((SC_DEV_PSCONSOLE  << 16) + SYSCONSOLE_DEV)
#define DEV_PSEUDO      ((SC_DEV_PSCONSOLE  << 16) + PSEUDO_DEV)
#define DEV_STDIN       ((SC_DEV_PSCONSOLE  << 16) + STDIN_DEV)
#define DEV_STDOUT      ((SC_DEV_PSCONSOLE  << 16) + STDOUT_DEV)
#define DEV_STDERR      ((SC_DEV_PSCONSOLE  << 16) + STDERR_DEV)
#define DEV_NULL        (SC_DEV_NULL       << 16)
#define DEV_MEMLOG      (SC_DEV_MEMLOG     << 16)
#define DEV_RDIO        (SC_DEV_RDIO       << 16)
#define DEV_DLPI        (SC_DEV_DLPI       << 16)
#define DEV_TFTP        (SC_DEV_TFTP       << 16)
#define DEV_NTFTP       (SC_DEV_NTFTP      << 16)
#define DEV_HTTP        (SC_DEV_HTTP       << 16)
#define DEV_SPI         (SC_DEV_SPI        << 16)
#define DEV_WATCHDOG    (SC_DEV_WATCHDOG   << 16)
#define DEV_FLOPPY      (SC_DEV_FLOPPY     << 16)
#define DEV_IDE         (SC_DEV_IDE        << 16)
#define DEV_CMOS        (SC_DEV_CMOS       << 16)
#define DEV_CONSOLE     (SC_DEV_CONSOLE    << 16)
#define DEV_IP          (SC_IP             << 16)
#define DEV_ARP         (SC_ARP            << 16)
#define DEV_TCP         (SC_TCP            << 16)
#define DEV_UDP         (SC_UDP            << 16)
#define DEV_RAW         (SC_RAW            << 16)
#define DEV_LOOP        (SC_LOOP           << 16)
#define DEV_PHPI        (SC_PHPI           << 16)
#define DEV_LAPB        (SC_LAPB           << 16)
#define DEV_X25         (SC_X25            << 16)
#define DEV_SNDCF       (SC_SNDCF          << 16)
#define DEV_IPCONV      (SC_IPCONV         << 16)
#define DEV_PH          (SC_PH             << 16)
#define DEV_LAPD        (SC_LAPD           << 16)
#define DEV_IPCD        (SC_IPCD           << 16)
#define DEV_FRMUX       (SC_FRMUX          << 16)
#define DEV_PIM         (SC_PIM            << 16)
#define DEV_PPP         (SC_PPP            << 16)
#define DEV_LOG         (SC_DEV_LOG        << 16)
#define DEV_PSMUX       (SC_DEV_PSMUX      << 16)
#define DEV_PSLWR       (SC_DEV_PSLWR      << 16)
#define DEV_SLLWR       (SC_DEV_SLLWR      << 16)
#define DEV_PIPE        (SC_DEV_PIPE       << 16)

#if (BSP_CPUFAMILY == FAMILY_X86) && (SC_APP_CONSOLE == PCCON)
    #define CONSOLE   DEV_CONSOLE
#else
    #define CONSOLE   DEV_SERIAL
#endif

/***********************************************************************/
/*            p S E U D O   D R I V E R   D E F I N E S                */
/*                                                                     */
/* The defines below control the behavour of the pSEUDO driver if the  */
/* SC_DEV_PSCONSOLE is enabled.                                        */
/*                                                                     */
/***********************************************************************/
#define	SC_PSCNSL_SHARED_CHAN	2        /* Num of shared channels     */
#define	SC_PSCNSL_PRIVATE_CHAN	4        /* Number of private channels */
#define	SC_PSCNSL_MAX_CUSTOM	1        /* NUmber of custome device   */
#define	SC_PSCNSL_DEFAULT_DEV	CONSOLE  /* Default console device     */

/***********************************************************************/
/*           T F T P   D R I V E R   C O N F I G U R A T I O N         */
/*                                                                     */
/* The defines below define the Configuration Parameters needed by the */
/* TFTP driver.                                                        */
/*                                                                     */
/***********************************************************************/
#define SC_MAX_TFTP_CHAN    8       /* Maximum number of TFTP channels */

/***********************************************************************/
/*           H T T P    S E R V E R   C O N F I G U R A T I O N        */
/*                                                                     */
/* The SC_MAX_HTTP_CHAN define controls the maximum number of HTTP     */
/* channels in the system.                                             */
/*                                                                     */
/***********************************************************************/
#define SC_MAX_HTTP_CHAN    1