rfc2266.mib

wm PNE 3.3 source code, running at more than vxworks6.x version.

                      When Training_Up is received by the repeater on a
                      local port (or when Training_Down is received on
                      a cascade port), vgRptrPortStatus will change to
                      'training(3)' and vgRptrTrainingResult can be
                      monitored to see the detailed status regarding
                      training.

                      When 24 consecutive good FCS packets are exchanged
                      and the configuration bits are OK,
                      vgRptrPortStatus will change to 'active(1)'.

                      A disabled port shall have a port status of
                      'inactive(2)'."
              REFERENCE
                      "IEEE Standard 802.12, 13.2.4.5.1,
                      aPortStatus."
              ::= { vgRptrBasicPortEntry 4 }

          vgRptrPortSupportedPromiscMode OBJECT-TYPE
              SYNTAX     INTEGER {
                             singleModeOnly(1),
                             singleOrPromiscMode(2),
                             promiscModeOnly(3)
                         }
              MAX-ACCESS read-only
              STATUS     current
              DESCRIPTION
                      "This object describes whether the port hardware
                      is capable of supporting promiscuous mode, single
                      address mode (i.e., repeater filters unicasts not
                      addressed to the end station attached to this
                      port), or both.  A port for which vgRptrPortType
                      is equal to 'cascadeInternal' or 'cascadeExternal'
                      will always have a value of 'promiscModeOnly' for
                      this object."
              REFERENCE
                      "IEEE Standard 802.12-1995, 13.2.4.5.1,
                      aSupportedPromiscMode."
              ::= { vgRptrBasicPortEntry 5 }

          vgRptrPortSupportedCascadeMode OBJECT-TYPE
              SYNTAX     INTEGER {
                             endNodesOnly(1),
                             endNodesOrRepeaters(2),
                             cascadePort(3)
                         }
              MAX-ACCESS read-only
              STATUS     current
              DESCRIPTION
                      "This object describes whether the port hardware
                      is capable of supporting cascaded repeaters, end
                      nodes, or both.  A port for which vgRptrPortType
                      is equal to 'cascadeInternal' or
                      'cascadeExternal' will always have a value of
                      'cascadePort' for this object."
              REFERENCE
                      "IEEE Standard 802.12-1995, 13.2.4.5.1,
                      aSupportedCascadeMode."
              ::= { vgRptrBasicPortEntry 6 }

          vgRptrPortAllowedTrainType OBJECT-TYPE
              SYNTAX     INTEGER {
                             allowEndNodesOnly(1),
                             allowPromiscuousEndNodes(2),
                             allowEndNodesOrRepeaters(3),
                             allowAnything(4)
                         }
              MAX-ACCESS read-write
              STATUS     current
              DESCRIPTION
                      "This security object is set by the network
                      manager to configure what type of device is
                      permitted to connect to the port.  One of the
                      following values:

                          allowEndNodesOnly        - only non-
                                                     promiscuous end
                                                     nodes permitted.
                          allowPromiscuousEndNodes - promiscuous or
                                                     non-promiscuous
                                                     end nodes
                                                     permitted
                          allowEndNodesOrRepeaters - repeaters or non-
                                                     promiscuous end
                                                     nodes permitted
                          allowAnything            - repeaters,
                                                     promiscuous or
                                                     non-promiscuous
                                                     end nodes
                                                     permitted

                      For a port for which vgRptrPortType is equal to
                      'cascadeInternal' or 'cascadeExternal', the
                      corresponding instance of this object may not be
                      set to 'allowEndNodesOnly' or
                      'allowPromiscuousEndNodes'.

                      The agent must reject a SET of this object if the
                      value includes no capabilities that are
                      supported by this port's hardware, as defined by
                      the values of the corresponding instances of
                      vgRptrPortSupportedPromiscMode and
                      vgRptrPortSupportedCascadeMode.

                      Note that vgRptrPortSupportPromiscMode and
                      vgRptrPortSupportedCascadeMode represent what the
                      port hardware is capable of supporting.
                      vgRptrPortAllowedTrainType is used for setting an
                      administrative policy for a port.  The actual set
                      of training configurations that will be allowed
                      to succeed on a port is the intersection of what
                      the hardware will support and what is
                      administratively allowed.  The above requirement
                      on what values may be set to this object says that
                      the intersection of what is supported and what is
                      allowed must be non-empty.  In other words, it
                      must not result in a situation in which nothing
                      would be allowed to train on that port.  However,
                      a value can be set to this object as long as the
                      combination of this object and what is supported
                      by the hardware would still leave at least one
                      configuration that could successfully train on the
                      port.

                      The value of this object should be preserved
                      across repeater resets and power failures."
              REFERENCE
                      "IEEE Standard 802.12-1995, 13.2.4.5.1,
                      aAllowableTrainingType."
              ::= { vgRptrBasicPortEntry 7 }

          vgRptrPortLastTrainConfig OBJECT-TYPE
              SYNTAX     OCTET STRING (SIZE(2))
              MAX-ACCESS read-only
              STATUS     current
              DESCRIPTION
                      "This object is a 16 bit field.  For local ports,
                      this object contains the requested configuration
                      field from the most recent error-free training
                      request frame sent by the device connected to
                      the port.  For cascade ports, this object contains
                      the responder's allowed configuration field from
                      the most recent error-free training response frame
                      received in response to training initiated by this
                      repeater.  The format of the current version of
                      this field is described in section 3.2.  Please
                      refer to the most recent version of the IEEE
                      802.12 standard for the most up-to-date definition
                      of the format of this object."
              REFERENCE
                      "IEEE Standard 802.12-1995, 13.2.4.5.1,
                      aLastTrainingConfig."
              ::= { vgRptrBasicPortEntry 8 }

          vgRptrPortTrainingResult OBJECT-TYPE
              SYNTAX     OCTET STRING (SIZE(3))
              MAX-ACCESS read-only
              STATUS     current
              DESCRIPTION
                      "This 18 bit field is used to indicate the result
                      of training.  It contains two bits which indicate
                      if error-free training frames have been received,
                      and it also contains the 16 bits of the allowed
                      configuration field from the most recent
                      error-free training response frame on the port.

                        First Octet:    Second and Third Octets:
                        7 6 5 4 3 2 1 0
                       +-+-+-+-+-+-+-+-+-----------------------------+
                       |0|0|0|0|0|0|V|G| allowed configuration field |
                       +-+-+-+-+-+-+-+-+-----------------------------+

                          V:   Valid: set when at least one error-free
                               training frame has been received.
                               Indicates the 16 training configuration
                               bits in vgRptrPortLastTrainConfig and
                               vgRptrPortTrainingResult contain valid
                               information.  This bit is cleared when
                               vgRptrPortStatus transitions to the
                               'inactive' or 'training' state.
                          G:   LinkGood: indicates the link hardware is
                               OK.  Set if 24 consecutive error-free
                               training packets have been exchanged.
                               Cleared when a training packet with
                               errors is received, or when
                               vgRptrPortStatus transitions to the
                               'inactive' or 'training' state.

                      The format of the current version of the allowed
                      configuration field is described in section 3.2.
                      Please refer to the most recent version of the
                      IEEE 802.12 standard for the most up-to-date
                      definition of the format of this field.

                      If the port is in training, a management station
                      can examine this object to see if any training
                      packets have been passed successfully.  If there
                      have been any good training packets, the Valid
                      bit will be set and the management station can
                      examine the allowed configuration field to see if
                      there is a duplicate address, configuration, or
                      security problem.

                      Note that on a repeater local port, this repeater
                      generates the training response bits, while on
                      a cascade port, the device at the upper end of
                      the link originated the training response bits."
              REFERENCE
                      "IEEE Standard 802.12-1995, 13.2.4.5.1,
                      aTrainingResult."
              ::= { vgRptrBasicPortEntry 9 }
          vgRptrPortPriorityEnable OBJECT-TYPE
              SYNTAX     TruthValue
              MAX-ACCESS read-write
              STATUS     current
              DESCRIPTION
                      "A configuration flag used to determine whether
                      the repeater will service high priority requests
                      received on the port as high priority or normal
                      priority.  When 'false', high priority requests
                      on this port will be serviced as normal priority.

                      The setting of this object has no effect on a
                      cascade port.  Also note that the setting of this
                      object has no effect on a port connected to a
                      cascaded repeater.  In both of these cases, this
                      setting is treated as always 'true'.  The value
                      'false' only has an effect when the port is a
                      localInternal or localExternal port connected to
                      an end node.

                      The value of this object should be preserved
                      across repeater resets and power failures."
              REFERENCE
                      "IEEE Standard 802.12-1995, 13.2.4.5.1,
                      aPriorityEnable."
              ::= { vgRptrBasicPortEntry 10 }

          vgRptrPortRptrInfoIndex OBJECT-TYPE
              SYNTAX     Integer32 (0..2147483647)
              MAX-ACCESS read-only
              STATUS     current
              DESCRIPTION
                      "This object identifies the repeater that this
                      port is currently mapped to.  The repeater
                      identified by a particular value of this object
                      is the same as that identified by the same value
                      of vgRptrInfoIndex.  A value of zero indicates
                      that this port is not currently mapped to any
                      repeater."
              ::= { vgRptrBasicPortEntry 11 }


          vgRptrMonitor      OBJECT IDENTIFIER ::= { vgRptrObjects 2 }

          vgRptrMonRepeater  OBJECT IDENTIFIER ::= { vgRptrMonitor 1 }

          vgRptrMonitorTable OBJECT-TYPE
              SYNTAX     SEQUENCE OF VgRptrMonitorEntry
              MAX-ACCESS not-accessible
              STATUS     current
              DESCRIPTION
                      "A table of performance and error statistics for
                      each repeater in the system.  The instance of the
                      vgRptrInfoLastChange associated with a repeater
                      is used to indicate possible discontinuities of
                      the counters in this table that are associated
                      with the same repeater."
              ::= { vgRptrMonRepeater 1 }

          vgRptrMonitorEntry OBJECT-TYPE
              SYNTAX     VgRptrMonitorEntry
              MAX-ACCESS not-accessible