rfc2127.mib

wm PNE 3.3 source code, running at more than vxworks6.x version.

             the hyperchannel.

             If since system startup there was no call on this
             interface, this object has a value of false(2)."
        REFERENCE
            "Q.931 [8], chapter 4.5.5."
        ::= { isdnBearerEntry 8 }

isdnBearerCallSetupTime         OBJECT-TYPE
        SYNTAX      TimeStamp
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The value of sysUpTime when the ISDN setup message for
             the current or last call was sent or received. If since
             system startup there has been no call on this interface,
             this object has a value of zero."
        ::= { isdnBearerEntry 9 }

isdnBearerCallConnectTime       OBJECT-TYPE
        SYNTAX      TimeStamp
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The value of sysUpTime when the ISDN connect message for
             the current or last call was sent or received. If since
             system startup there has been no call on this interface,
             this object has a value of zero."
        ::= { isdnBearerEntry 10 }

isdnBearerChargedUnits          OBJECT-TYPE
        SYNTAX      Gauge32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of charged units for the current or last
             connection. For incoming calls or if charging information
             is not supplied by the switch, the value of this object
             is zero."
        ::= { isdnBearerEntry 11 }

-- ISDN signaling group

isdnSignalingGroup OBJECT IDENTIFIER ::= { isdnMibObjects 3 }

-- signaling channel configuration table
-- There is one entry in this table for each Terminal Endpoint
-- (link layer connection to the switch).
-- Usually, there is one endpoint per D channel. In some
-- cases, however, there can be multiple endpoints.
-- Thus, entries in this table can be created and deleted.
-- This also means the creation of an associated ifEntry.
--
-- D channel backup and NFAS trunks are handled using the
-- ifStack table.
-- In case of D channel backup, there are multiple
-- Data Link Layer (LAPD) interfaces. Only one interface is
-- active; all others are dormant(5).
-- In case of NFAS trunks, one lower interface is the
-- LAPD interface, while the other lower interfaces are physical
-- interfaces.

-- If directory number and calling address differ from each other
-- or multiple directory numbers are being used,
-- the isdnDirectoryTable has to be used to enter such
-- directory numbers.

isdnSignalingGetIndex OBJECT-TYPE
        SYNTAX      TestAndIncr
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "The recommended procedure for selecting a new index for
             isdnSignalingTable row creation is to GET the value of
             this object, and then to SET the object with the same
             value. If the SET operation succeeds, the manager can use
             this value as an index to create a new row in this table."
        REFERENCE
            "RFC1903, TestAndIncr textual convention."
        ::= { isdnSignalingGroup 1 }

isdnSignalingTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF IsdnSignalingEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "ISDN signaling table containing configuration and
             operational parameters for all ISDN signaling
             channels on this managed device."
        ::= { isdnSignalingGroup 2 }

isdnSignalingEntry OBJECT-TYPE
        SYNTAX      IsdnSignalingEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "An entry in the ISDN Signaling Table. To create a new
             entry, only isdnSignalingProtocol needs to be specified
             before isdnSignalingStatus can become active(1)."
        INDEX { isdnSignalingIndex }
        ::= { isdnSignalingTable 1 }

IsdnSignalingEntry ::= SEQUENCE {
            isdnSignalingIndex          INTEGER,
            isdnSignalingIfIndex        InterfaceIndex,
            isdnSignalingProtocol       IsdnSignalingProtocol,
            isdnSignalingCallingAddress DisplayString,
            isdnSignalingSubAddress     DisplayString,
            isdnSignalingBchannelCount  Integer32,
            isdnSignalingInfoTrapEnable INTEGER,
            isdnSignalingStatus         RowStatus
        }

isdnSignalingIndex OBJECT-TYPE
        SYNTAX      INTEGER (1..2147483647)
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The index value which uniquely identifies an entry
             in the isdnSignalingTable."
        ::= { isdnSignalingEntry 1 }

isdnSignalingIfIndex OBJECT-TYPE
        SYNTAX      InterfaceIndex
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The ifIndex value of the interface associated with this
             signaling channel."
        ::= { isdnSignalingEntry 2 }

isdnSignalingProtocol OBJECT-TYPE
        SYNTAX      IsdnSignalingProtocol
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The particular protocol type supported by the
             switch providing access to the ISDN network
             to which this signaling channel is connected."
        ::= { isdnSignalingEntry 3 }

isdnSignalingCallingAddress OBJECT-TYPE
        SYNTAX      DisplayString
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The ISDN Address to be assigned to this signaling
             channel. More specifically, this is the 'Calling Address
             information element' as being passed to the switch
             in outgoing call setup messages.

             It can be an EAZ (1TR6), a calling number (DSS1, ETSI)
             or any other number necessary to identify a signaling
             interface. If there is no such number defined or required,
             this is a zero length string. It is represented in
             DisplayString form.

             Incoming calls can also be identified by this number.
             If the Directory Number, i.e. the Called Number in
             incoming calls, is different to this number, the
             isdnDirectoryTable has to be used to specify all
             possible Directory Numbers.

             The format of this information largely depends on the type
             of switch or PBX the device is connected to. Therefore,
             the detailed format of this information is not
             specified and is implementation dependent.

             If possible, the agent should implement this information
             using the E.164 number format. In this case, the number
             must start with '+'. Otherwise, IA5 number digits must
             be used."
        REFERENCE
            "ITU-T E.164, Q.931 chapter 4.5.10"
        DEFVAL { "" }
        ::= { isdnSignalingEntry 4 }

isdnSignalingSubAddress OBJECT-TYPE
        SYNTAX      DisplayString
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Supplementary information to the ISDN address assigned
             to this signaling channel. Usually, this is the
             subaddress as defined in Q.931.
             If there is no such number defined or required, this is
             a zero length string.
             The subaddress is used for incoming calls as well as
             for outgoing calls.
             The subaddress is an user supplied string of up to 20
             IA5 characters and is transmitted transparently through
             the network."
        REFERENCE
            "ITU-T I.330, Q.931 chapter 4.5.11"
        DEFVAL { "" }
        ::= { isdnSignalingEntry 5 }

isdnSignalingBchannelCount OBJECT-TYPE
        SYNTAX      Integer32 (1..65535)
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The total number of B channels (bearer channels)
             managed by this signaling channel. The default value
             of this object depends on the physical interface type
             and is either 2 for Basic Rate interfaces or
             24 (30) for Primary Rate interfaces."
        ::= { isdnSignalingEntry 6 }

isdnSignalingInfoTrapEnable    OBJECT-TYPE
        SYNTAX      INTEGER {
            enabled(1),
            disabled(2)
        }
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Indicates whether isdnMibCallInformation traps
             should be generated for calls on this signaling
             channel."
        DEFVAL      { disabled }
        ::= { isdnSignalingEntry 7 }

isdnSignalingStatus OBJECT-TYPE
        SYNTAX      RowStatus
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "This object is used to create and delete rows in the
             isdnSignalingTable."
        ::= { isdnSignalingEntry 8 }

-- Signaling channel statistics table
-- There is one entry for each signaling connection
-- in this table.
-- Note that the ifEntry also has some statistics information.

isdnSignalingStatsTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF IsdnSignalingStatsEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "ISDN signaling table containing statistics
             information for all ISDN signaling channels
             on this managed device.
             Only statistical information which is not already being
             counted in the ifTable is being defined in this table."
        ::= { isdnSignalingGroup 3 }

isdnSignalingStatsEntry OBJECT-TYPE
        SYNTAX      IsdnSignalingStatsEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "An entry in the ISDN Signaling statistics Table."
        AUGMENTS { isdnSignalingEntry }
        ::= { isdnSignalingStatsTable 1 }

IsdnSignalingStatsEntry ::= SEQUENCE {
            isdnSigStatsInCalls         Counter32,
            isdnSigStatsInConnected     Counter32,
            isdnSigStatsOutCalls        Counter32,
            isdnSigStatsOutConnected    Counter32,
            isdnSigStatsChargedUnits    Counter32
        }

isdnSigStatsInCalls OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of incoming calls on this interface."
        ::= { isdnSignalingStatsEntry 1 }

isdnSigStatsInConnected OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of incoming calls on this interface
             which were actually connected."
        ::= { isdnSignalingStatsEntry 2 }

isdnSigStatsOutCalls OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of outgoing calls on this interface."
        ::= { isdnSignalingStatsEntry 3 }

isdnSigStatsOutConnected OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of outgoing calls on this interface
             which were actually connected."
        ::= { isdnSignalingStatsEntry 4 }

isdnSigStatsChargedUnits OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of charging units on this interface since
             system startup.
             Only the charging units applying to the local interface,
             i.e. for originated calls or for calls with 'Reverse
             charging' being active, are counted here."
        ::= { isdnSignalingStatsEntry 5 }

--
-- The LAPD table

isdnLapdTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF IsdnLapdEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Table containing configuration and statistics
             information for all LAPD (D channel Data Link)
             interfaces on this managed device.
             Only statistical information which is not already being
             counted in the ifTable is being defined in this table."
        ::= { isdnSignalingGroup 4 }

isdnLapdEntry OBJECT-TYPE
        SYNTAX      IsdnLapdEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "An entry in the LAPD Table."
        INDEX { ifIndex }
        ::= { isdnLapdTable 1 }

IsdnLapdEntry ::= SEQUENCE {
            isdnLapdPrimaryChannel  TruthValue,
            isdnLapdOperStatus      INTEGER,
            isdnLapdPeerSabme       Counter32,
            isdnLapdRecvdFrmr       Counter32
        }

isdnLapdPrimaryChannel OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "If set to true(1), this D channel is the designated
             primary D channel if D channel backup is active.
             There must be exactly one primary D channel
             configured. If D channel backup is not used, this
             object has a value of true(1)."
        REFERENCE
            "Q.931 [8], Annex F, D channel backup procedures."
        ::= { isdnLapdEntry 1 }

isdnLapdOperStatus OBJECT-TYPE
        SYNTAX      INTEGER {
            inactive(1),
            l1Active(2),
            l2Active(3)
        }
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The operational status of this interface:

             inactive  all layers are inactive
             l1Active  layer 1 is activated,
                       layer 2 datalink not established
             l2Active  layer 1 is activated,
                       layer 2 datalink established."
        ::= { isdnLapdEntry 2 }

isdnLapdPeerSabme OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of peer SABME frames received on this
             interface. This is the number of peer-initiated
             new connections on this interface."
        ::= { isdnLapdEntry 3 }

isdnLapdRecvdFrmr OBJECT-TYPE
        SYNTAX      Counter32
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The number of LAPD FRMR response frames received.
             This is the number of framing errors on this
             interface."
        ::= { isdnLapdEntry 4 }

--
-- Optional groups follow here.
-- The Terminal Endpoint group and table

-- This table is required only if TEI values or SPID numbers
-- have to be entered.
-- The ifIndex values for this table are identical to those of
-- the isdnSignalingChannel table.

isdnEndpointGroup OBJECT IDENTIFIER ::= { isdnMibObjects 4 }

isdnEndpointGetIndex OBJECT-TYPE
        SYNTAX      TestAndIncr
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "The recommended procedure for selecting a new index for
             isdnEndpointTable row creation is to GET the value of
             this object, and then to SET the object with the same
             value. If the SET operation succeeds, the manager can use
             this value as an index to create a new row in this table."
        REFERENCE