rfc1659.mib

wm PNE 3.3 source code, running at more than vxworks6.x version.

   rs232SyncPortInterruptedFrames OBJECT-TYPE
       SYNTAX Counter32
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "Total number of frames that failed to be received
           or transmitted on the port due to loss of modem
           signals since system re-initialization and while the
           port state was 'up' or 'test'."
       ::= { rs232SyncPortEntry 6 }

   rs232SyncPortAbortedFrames OBJECT-TYPE
       SYNTAX Counter32
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "Number of frames aborted on the port due to
           receiving an abort sequence since system
           re-initialization and while the port state was 'up'
           or 'test'."
       ::= { rs232SyncPortEntry 7 }

   rs232SyncPortRole OBJECT-TYPE
       SYNTAX INTEGER  { dte(1), dce(2) }
       MAX-ACCESS read-write
       STATUS current
       DESCRIPTION
           "The role the device is playing that is using this port.
              dte    means the device is performing the role of
                     data terminal equipment
              dce    means the device is performing the role of
                     data circuit-terminating equipment."
       DEFVAL { dce }
       ::= { rs232SyncPortEntry 8 }

   rs232SyncPortEncoding OBJECT-TYPE
       SYNTAX INTEGER  { nrz(1), nrzi(2) }
       MAX-ACCESS read-write
       STATUS current
       DESCRIPTION
           "The bit stream encoding technique that is in effect
            for this port.
              nrz    for Non-Return to Zero encoding
              nrzi   for Non-Return to Zero Inverted encoding."
       DEFVAL { nrz }
       ::= { rs232SyncPortEntry 9 }

   rs232SyncPortRTSControl OBJECT-TYPE
       SYNTAX INTEGER  { controlled(1), constant(2) }
       MAX-ACCESS read-write
       STATUS current
       DESCRIPTION
           "The method used to control the Request To Send (RTS)
            signal.

              controlled  when the DTE is asserts RTS each time
                          data needs to be transmitted and drops
                          RTS at some point after data
                          transmission begins.

                          If rs232SyncPortRole is 'dte', the
                          RTS is an output signal. The device
                          will issue a RTS and wait for a CTS
                          from the DCE before starting to
                          transmit.

                          If rs232SyncPortRole is 'dce', the
                          RTS is an input signal. The device
                          will issue a CTS only after having
                          received RTS and waiting the
                          rs232SyncPortRTSCTSDelay interval.

              constant    when the DTE constantly asserts RTS."
       DEFVAL { constant }
       ::= { rs232SyncPortEntry 10 }

   rs232SyncPortRTSCTSDelay OBJECT-TYPE
       SYNTAX Integer32
       MAX-ACCESS read-write
       STATUS current
       DESCRIPTION
           "The interval (in milliseconds) that the DCE must wait
            after it sees RTS asserted before asserting CTS.  This
            object exists in support of older synchronous devices
            that cannot recognize CTS within a certain interval
            after it asserts RTS."
       DEFVAL { 0 }
       ::= { rs232SyncPortEntry 11 }

   rs232SyncPortMode OBJECT-TYPE
       SYNTAX INTEGER  { fdx(1), hdx(2), simplex-receive(3),
                         simplex-send(4) }
       MAX-ACCESS read-write
       STATUS current
       DESCRIPTION
           "The mode of operation of the port with respect to the
            direction and simultaneity of data transfer.

              fdx              when frames on the data link can be
                               transmitted and received at the same
                               time

              hdx              when frames can either be received
                               from the data link or transmitted
                               onto the data link but not at the
                               same time.

              simplex-receive  when frames can only be received on
                               this data link.

              simplex-send     when frames can only be sent on this
                               data link."
       DEFVAL { fdx }
       ::= { rs232SyncPortEntry 12 }

   rs232SyncPortIdlePattern OBJECT-TYPE
       SYNTAX INTEGER  { mark(1), space(2) }
       MAX-ACCESS read-write
       STATUS current
       DESCRIPTION
           "The bit pattern used to indicate an idle line."
       DEFVAL { space }
       ::= { rs232SyncPortEntry 13 }

   rs232SyncPortMinFlags OBJECT-TYPE
       SYNTAX Integer32
       MAX-ACCESS read-write
       STATUS current
       DESCRIPTION
           "The minimum number of flag patterns this port needs in
            order to recognize the end of one frame and the start
            of the next.  Plausible values are 1 and 2."
       DEFVAL { 2 }
       ::= { rs232SyncPortEntry 14 }


   -- Input Signal Table

   rs232InSigTable OBJECT-TYPE
       SYNTAX SEQUENCE OF Rs232InSigEntry
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "A list of port input control signal entries
           implemented and visible to the software on the port,
           and useful to monitor."
       ::= { rs232 5 }

   rs232InSigEntry OBJECT-TYPE
       SYNTAX Rs232InSigEntry
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "Input control signal status for a hardware port."
       INDEX { rs232InSigPortIndex, rs232InSigName }
       ::= { rs232InSigTable 1 }

   Rs232InSigEntry ::=
       SEQUENCE {
           rs232InSigPortIndex
               InterfaceIndex,
           rs232InSigName
               INTEGER,
           rs232InSigState
               INTEGER,
           rs232InSigChanges
               Counter32
       }

   rs232InSigPortIndex OBJECT-TYPE
       SYNTAX InterfaceIndex
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "The value of rs232PortIndex for the port to which
           this entry belongs."
       ::= { rs232InSigEntry 1 }

   rs232InSigName OBJECT-TYPE
       SYNTAX INTEGER { rts(1), cts(2), dsr(3), dtr(4), ri(5),
                        dcd(6), sq(7), srs(8), srts(9),
                        scts(10), sdcd(11) }
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "Identification of a hardware signal, as follows:

               rts    Request to Send
               cts    Clear to Send
               dsr    Data Set Ready
               dtr    Data Terminal Ready
               ri     Ring Indicator
               dcd    Received Line Signal Detector
               sq     Signal Quality Detector
               srs    Data Signaling Rate Selector
               srts   Secondary Request to Send
               scts   Secondary Clear to Send
               sdcd   Secondary Received Line Signal Detector
           "
       REFERENCE
           "EIA Standard RS-232-C, August 1969."
       ::= { rs232InSigEntry 2 }

   rs232InSigState OBJECT-TYPE
       SYNTAX INTEGER { none(1), on(2), off(3) }
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "The current signal state."
       ::= { rs232InSigEntry 3 }

   rs232InSigChanges OBJECT-TYPE
       SYNTAX Counter32
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "The number of times the signal has changed from
           'on' to 'off' or from 'off' to 'on'."
       ::= { rs232InSigEntry 4 }


   -- Output Signal Table

   rs232OutSigTable OBJECT-TYPE
       SYNTAX SEQUENCE OF Rs232OutSigEntry
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "A list of port output control signal entries
           implemented and visible to the software on the port,
           and useful to monitor."
       ::= { rs232 6 }

   rs232OutSigEntry OBJECT-TYPE
       SYNTAX Rs232OutSigEntry
       MAX-ACCESS not-accessible
       STATUS current
       DESCRIPTION
           "Output control signal status for a hardware port."
       INDEX { rs232OutSigPortIndex, rs232OutSigName }
       ::= { rs232OutSigTable 1 }

   Rs232OutSigEntry ::=
       SEQUENCE {
           rs232OutSigPortIndex
               InterfaceIndex,
           rs232OutSigName
               INTEGER,
           rs232OutSigState
               INTEGER,
           rs232OutSigChanges
               Counter32
       }

   rs232OutSigPortIndex OBJECT-TYPE
       SYNTAX InterfaceIndex
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "The value of rs232PortIndex for the port to which
           this entry belongs."
       ::= { rs232OutSigEntry 1 }

   rs232OutSigName OBJECT-TYPE
       SYNTAX INTEGER { rts(1), cts(2), dsr(3), dtr(4), ri(5),
                        dcd(6), sq(7), srs(8), srts(9),
                        scts(10), sdcd(11) }
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "Identification of a hardware signal, as follows:

               rts    Request to Send
               cts    Clear to Send
               dsr    Data Set Ready
               dtr    Data Terminal Ready
               ri     Ring Indicator
               dcd    Received Line Signal Detector
               sq     Signal Quality Detector
               srs    Data Signaling Rate Selector
               srts   Secondary Request to Send
               scts   Secondary Clear to Send
               sdcd   Secondary Received Line Signal Detector
           "
       REFERENCE
           "EIA Standard RS-232-C, August 1969."
       ::= { rs232OutSigEntry 2 }

   rs232OutSigState OBJECT-TYPE
       SYNTAX INTEGER { none(1), on(2), off(3) }
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "The current signal state."
       ::= { rs232OutSigEntry 3 }

   rs232OutSigChanges OBJECT-TYPE
       SYNTAX Counter32
       MAX-ACCESS read-only
       STATUS current
       DESCRIPTION
           "The number of times the signal has changed from
           'on' to 'off' or from 'off' to 'on'."
       ::= { rs232OutSigEntry 4 }


   -- conformance information

   rs232Conformance OBJECT IDENTIFIER ::= { rs232 7 }

   rs232Groups      OBJECT IDENTIFIER ::= { rs232Conformance 1 }
   rs232Compliances OBJECT IDENTIFIER ::= { rs232Conformance 2 }


   -- compliance statements

   rs232Compliance MODULE-COMPLIANCE
       STATUS  current
       DESCRIPTION
               "The compliance statement for SNMPv2 entities
               which have RS-232-like hardware interfaces."

       MODULE  -- this module
           MANDATORY-GROUPS { rs232Group }

           GROUP   rs232AsyncGroup
           DESCRIPTION
               "The Asynch group is mandatory only for those
                SNMPv2 entities which have asynchronous
                interfaces Rs-232-like."

           GROUP   rs232SyncGroup
           DESCRIPTION
               "The Synch group is mandatory only for those
                SNMPv2 entities which have synchronous
                interfaces Rs-232-like."
       ::= { rs232Compliances 1 }

   -- units of conformance

   rs232Group    OBJECT-GROUP
       OBJECTS { rs232Number, rs232PortIndex, rs232PortType,
                 rs232PortInSigNumber, rs232PortOutSigNumber,
                 rs232PortInSpeed, rs232PortOutSpeed,
                 rs232PortInFlowType, rs232PortOutFlowType,
                 rs232InSigPortIndex, rs232InSigName,
                 rs232InSigState, rs232InSigChanges,
                 rs232OutSigPortIndex, rs232OutSigName,
                 rs232OutSigState, rs232OutSigChanges }
       STATUS  current
       DESCRIPTION
               "A collection of objects providing information
                applicable to all RS-232-like interfaces."
       ::= { rs232Groups 1 }

   rs232AsyncGroup OBJECT-GROUP
       OBJECTS { rs232AsyncPortIndex, rs232AsyncPortBits,
                 rs232AsyncPortStopBits, rs232AsyncPortParity,
                 rs232AsyncPortAutobaud, rs232AsyncPortParityErrs,
                 rs232AsyncPortFramingErrs, rs232AsyncPortOverrunErrs }
       STATUS  current
       DESCRIPTION
               "A collection of objects providing information
                applicable to asynchronous RS-232-like interfaces."
       ::= { rs232Groups 2 }

   rs232SyncGroup OBJECT-GROUP
       OBJECTS { rs232SyncPortIndex, rs232SyncPortClockSource,
                 rs232SyncPortFrameCheckErrs,
                 rs232SyncPortTransmitUnderrunErrs,
                 rs232SyncPortReceiveOverrunErrs,
                 rs232SyncPortInterruptedFrames,
                 rs232SyncPortAbortedFrames }
       STATUS  current
       DESCRIPTION
               "A collection of objects providing information
                applicable to synchronous RS-232-like interfaces."
       ::= { rs232Groups 3 }

   rs232SyncSDLCGroup OBJECT-GROUP
       OBJECTS { rs232SyncPortRole,
                 rs232SyncPortEncoding,
                 rs232SyncPortRTSControl,
                 rs232SyncPortRTSCTSDelay,
                 rs232SyncPortMode,
                 rs232SyncPortIdlePattern,
                 rs232SyncPortMinFlags }
       STATUS  current
       DESCRIPTION
               "A collection of objects providing information
                applicable to synchronous RS-232-like interfaces
                running SDLC."
       ::= { rs232Groups 4 }

   END