rfc2128.mib

wm PNE 3.3 source code, running at more than vxworks6.x version.

DIAL-CONTROL-MIB DEFINITIONS ::= BEGIN

IMPORTS
        MODULE-IDENTITY,
        NOTIFICATION-TYPE,
        OBJECT-TYPE,
        Unsigned32
                FROM SNMPv2-SMI
        TEXTUAL-CONVENTION,
        DisplayString,
        TimeStamp,
        RowStatus
                 FROM SNMPv2-TC
        MODULE-COMPLIANCE,
        OBJECT-GROUP,
        NOTIFICATION-GROUP
                FROM SNMPv2-CONF
        IANAifType
                FROM IANAifType-MIB
        ifOperStatus,
        ifIndex,
        InterfaceIndex,
        InterfaceIndexOrZero
                FROM IF-MIB
        transmission
                FROM RFC1213-MIB;

dialControlMib MODULE-IDENTITY
        LAST-UPDATED    "9609231544Z" -- Sep 23, 1996
        ORGANIZATION    "IETF ISDN Working Group"
        CONTACT-INFO
            "        Guenter Roeck
             Postal: cisco Systems
                     170 West Tasman Drive
                     San Jose, CA 95134
                     U.S.A.
             Phone:  [phone]
             E-mail: [e-mail]"
        DESCRIPTION
            "The MIB module to describe peer information for
             demand access and possibly other kinds of interfaces."
        ::= { transmission 21 }

AbsoluteCounter32 ::= TEXTUAL-CONVENTION
        STATUS      current
        DESCRIPTION
            "Represents a Counter32-like value that starts at zero,
             does not decrease, and does not wrap. This may be used
             only in situations where wrapping is not possible or
             extremely unlikely. Should such a counter overflow,
             it locks at the maxium value of 4,294,967,295.

             The primary use of this type of counter is situations
             where a counter value is to be recorded as history
             and is thus no longer subject to reading for changing
             values."
        SYNTAX      Unsigned32

-- Dial Control Mib objects definitions

dialControlMibObjects OBJECT IDENTIFIER ::= { dialControlMib 1 }

-- General configuration group

dialCtlConfiguration OBJECT IDENTIFIER ::= { dialControlMibObjects 1 }

-- general configuration data/parameters

dialCtlAcceptMode OBJECT-TYPE
        SYNTAX INTEGER {
            acceptNone(1),
            acceptAll(2),
            acceptKnown(3)
        }
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "The security level for acceptance of incoming calls.
             acceptNone(1)  - incoming calls will not be accepted
             acceptAll(2)   - incoming calls will be accepted,
                              even if there is no matching entry
                              in the dialCtlPeerCfgTable
             acceptKnown(3) - incoming calls will be accepted only
                              if there is a matching entry in the
                              dialCtlPeerCfgTable
            "
        ::= { dialCtlConfiguration 1 }

dialCtlTrapEnable OBJECT-TYPE
        SYNTAX      INTEGER {
            enabled(1),
            disabled(2)
        }
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "This object indicates whether dialCtlPeerCallInformation
             and dialCtlPeerCallSetup traps should be generated for
             all peers. If the value of this object is enabled(1),
             traps will be generated for all peers. If the value
             of this object is disabled(2), traps will be generated
             only for peers having dialCtlPeerCfgTrapEnable set
             to enabled(1)."
        DEFVAL      { disabled }
        ::= { dialCtlConfiguration 2 }


-- Peer group

dialCtlPeer OBJECT IDENTIFIER ::= { dialControlMibObjects 2 }

-- peer configuration table

dialCtlPeerCfgTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF DialCtlPeerCfgEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The list of peers from which the managed device
             will accept calls or to which it will place them."
       ::= { dialCtlPeer 1 }

dialCtlPeerCfgEntry OBJECT-TYPE
        SYNTAX      DialCtlPeerCfgEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Configuration data for a single Peer. This entry is
             effectively permanent, and contains information
             to identify the peer, how to connect to the peer,
             how to identify the peer and its permissions.
             The value of dialCtlPeerCfgOriginateAddress must be
             specified before a new row in this table can become
             active(1). Any writeable parameters in an existing entry
             can be modified while the entry is active. The modification
             will take effect when the peer in question will be
             called the next time.
             An entry in this table can only be created if the
             associated ifEntry already exists."
        INDEX       { dialCtlPeerCfgId, ifIndex }
      ::= { dialCtlPeerCfgTable 1 }

DialCtlPeerCfgEntry ::= SEQUENCE {
            dialCtlPeerCfgId                 INTEGER,
            dialCtlPeerCfgIfType             IANAifType,
            dialCtlPeerCfgLowerIf            InterfaceIndexOrZero,
            dialCtlPeerCfgOriginateAddress   DisplayString,
            dialCtlPeerCfgAnswerAddress      DisplayString,
            dialCtlPeerCfgSubAddress         DisplayString,
            dialCtlPeerCfgClosedUserGroup    DisplayString,
            dialCtlPeerCfgSpeed              INTEGER,
            dialCtlPeerCfgInfoType           INTEGER,
            dialCtlPeerCfgPermission         INTEGER,
            dialCtlPeerCfgInactivityTimer    INTEGER,
            dialCtlPeerCfgMinDuration        INTEGER,
            dialCtlPeerCfgMaxDuration        INTEGER,
            dialCtlPeerCfgCarrierDelay       INTEGER,
            dialCtlPeerCfgCallRetries        INTEGER,
            dialCtlPeerCfgRetryDelay         INTEGER,
            dialCtlPeerCfgFailureDelay       INTEGER,
            dialCtlPeerCfgTrapEnable         INTEGER,
            dialCtlPeerCfgStatus             RowStatus
        }

dialCtlPeerCfgId OBJECT-TYPE
        SYNTAX      INTEGER (1..2147483647)
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This object identifies a single peer. There may
             be several entries in this table for one peer,
             defining different ways of reaching this peer.
             Thus, there may be several entries in this table
             with the same value of dialCtlPeerCfgId.
             Multiple entries for one peer may be used to support
             multilink as well as backup lines.
             A single peer will be identified by a unique value
             of this object. Several entries for one peer MUST
             have the same value of dialCtlPeerCfgId, but different
             ifEntries and thus different values of ifIndex."
        ::= { dialCtlPeerCfgEntry 1 }

dialCtlPeerCfgIfType OBJECT-TYPE
        SYNTAX      IANAifType
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The interface type to be used for calling this peer.
             In case of ISDN, the value of isdn(63) is to be used."
        DEFVAL      { other }
        ::= { dialCtlPeerCfgEntry 2 }

dialCtlPeerCfgLowerIf OBJECT-TYPE
        SYNTAX      InterfaceIndexOrZero
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "ifIndex value of an interface the peer will have to be
             called on. For example, on an ISDN interface, this can be
             the ifIndex value of a D channel or the ifIndex value of a
             B channel, whatever is appropriate for a given peer.
             As an example, for Basic Rate leased lines it will be
             necessary to specify a B channel ifIndex, while for
             semi-permanent connections the D channel ifIndex has
             to be specified.
             If the interface can be dynamically assigned, this object
             has a value of zero."
        DEFVAL      { 0 }
        ::= { dialCtlPeerCfgEntry 3 }

dialCtlPeerCfgOriginateAddress OBJECT-TYPE
        SYNTAX      DisplayString
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Call Address at which the peer will be called.
             Think of this as the set of characters following 'ATDT '
             or the 'phone number' included in a D channel call request.

             The structure of this information will be switch type
             specific. If there is no address information required
             for reaching the peer, i.e., for leased lines,
             this object will be a zero length string."
        ::= { dialCtlPeerCfgEntry 4 }

dialCtlPeerCfgAnswerAddress OBJECT-TYPE
        SYNTAX      DisplayString
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Calling Party Number information element, as for example
             passed in an ISDN SETUP message by a PBX or switch,
             for incoming calls.
             This address can be used to identify the peer.
             If this address is either unknown or identical
             to dialCtlPeerCfgOriginateAddress, this object will be
             a zero length string."
        DEFVAL      { "" }
        ::= { dialCtlPeerCfgEntry 5 }

dialCtlPeerCfgSubAddress OBJECT-TYPE
        SYNTAX      DisplayString
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Subaddress at which the peer will be called.
             If the subaddress is undefined for the given media or
             unused, this is a zero length string."
        DEFVAL      { "" }
        ::= { dialCtlPeerCfgEntry 6 }

dialCtlPeerCfgClosedUserGroup OBJECT-TYPE
        SYNTAX      DisplayString
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Closed User Group at which the peer will be called.
             If the Closed User Group is undefined for the given media
             or unused, this is a zero length string."
        REFERENCE
            "Q.931, chapter 4.6.1."
        DEFVAL      { "" }
        ::= { dialCtlPeerCfgEntry 7 }

dialCtlPeerCfgSpeed OBJECT-TYPE
        SYNTAX      INTEGER (0..2147483647)
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The desired information transfer speed in bits/second
             when calling this peer.
             The detailed media specific information, e.g. information
             type and information transfer rate for ISDN circuits,
             has to be extracted from this object.
             If the transfer speed to be used is unknown or the default
             speed for this type of interfaces, the value of this object
             may be zero."
        DEFVAL      { 0 }
        ::= { dialCtlPeerCfgEntry 8 }

dialCtlPeerCfgInfoType OBJECT-TYPE
        SYNTAX      INTEGER {
            other(1),
            speech(2),
            unrestrictedDigital(3),     -- 64k/s data
            unrestrictedDigital56(4),   -- with 56k rate adaption
            restrictedDigital(5),
            audio31(6),                 -- 3.1 kHz audio
            audio7(7),                  -- 7 kHz audio
            video(8),
            packetSwitched(9),
            fax(10)
        }
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The Information Transfer Capability to be used when
             calling this peer.

             speech(2) refers to a non-data connection, whereas
             audio31(6) and audio7(7) refer to data mode
             connections."
        DEFVAL      { other }
        ::= { dialCtlPeerCfgEntry 9 }

dialCtlPeerCfgPermission OBJECT-TYPE
        SYNTAX      INTEGER {
            originate(1),
            answer(2),
            both(3),               -- both originate & answer
            callback(4),
            none(5)
        }
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "Applicable permissions. callback(4) either rejects the
             call and then calls back, or uses the 'Reverse charging'