rfc2662.mib

wm PNE 3.3 source code, running at more than vxworks6.x version.

                 agent reset."
         ::= { adslAturPerfDataEntry 2 }

        adslAturPerfLprs  OBJECT-TYPE
             SYNTAX      Counter32
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of the number of Loss of Power failures since
                 agent reset."
         ::= { adslAturPerfDataEntry 3 }

         adslAturPerfESs  OBJECT-TYPE
             SYNTAX      Counter32
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of the number of Errored Seconds since agent
                 reset.  The errored second parameter is a count of
                 one-second intervals containing one or more crc
                 anomalies, or one or more los or sef defects."
         ::= { adslAturPerfDataEntry 4 }

         -- general 15 min interval information
         --
         adslAturPerfValidIntervals OBJECT-TYPE
             SYNTAX      INTEGER(0..96)
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "The number of previous 15-minute intervals in the
                 interval table for which data was collected.  Given
                 that <n> is the maximum # of intervals supported.
                 The value will be <n> unless the measurement was
                 (re-)started within the last (<n>*15) minutes, in which
                 case the value will be the number of complete 15
                 minute intervals for which the agent has at least
                 some data. In certain cases (e.g., in the case
                 where the agent is a proxy) it is possible that some
                 intervals are unavailable.  In this case, this
                 interval is the maximum interval number for
                 which data is available."
         ::= { adslAturPerfDataEntry 5 }

         adslAturPerfInvalidIntervals OBJECT-TYPE
             SYNTAX      INTEGER(0..96)
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "The number of intervals in the range from
                 0 to the value of adslAturPerfValidIntervals
                 for which no data is available. This object
                 will typically be zero except in cases where
                 the data for some intervals are not available
                 (e.g., in proxy situations)."
         ::= { adslAturPerfDataEntry 6 }

         -- 15 min current performance group
         --
         adslAturPerfCurr15MinTimeElapsed OBJECT-TYPE
             SYNTAX      AdslPerfTimeElapsed(0..899)
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Total elapsed seconds in this interval."
         ::= { adslAturPerfDataEntry 7 }

         adslAturPerfCurr15MinLofs OBJECT-TYPE
             SYNTAX      PerfCurrentCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of seconds in the current 15 minute interval
                 when there was Loss of Framing."
         ::= { adslAturPerfDataEntry 8 }

         adslAturPerfCurr15MinLoss  OBJECT-TYPE
             SYNTAX      PerfCurrentCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of seconds in the current 15 minute interval
                 when there was Loss of Signal."
         ::= { adslAturPerfDataEntry 9 }

         adslAturPerfCurr15MinLprs  OBJECT-TYPE
             SYNTAX      PerfCurrentCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of seconds in the current 15 minute interval
                 when there was Loss of Power."
         ::= { adslAturPerfDataEntry 10 }

         adslAturPerfCurr15MinESs OBJECT-TYPE
             SYNTAX      PerfCurrentCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                "Count of Errored Seconds in the current 15 minute
                interval.  The errored second parameter is a count of
                one-second intervals containing one or more crc
                anomalies, or one or more los or sef defects."

         ::= { adslAturPerfDataEntry 11 }

         -- 1-day current and previous performance group
         --
         adslAturPerfCurr1DayTimeElapsed OBJECT-TYPE
             SYNTAX      AdslPerfTimeElapsed(0..86399)
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Number of seconds that have elapsed since the
                 beginning of the current 1-day interval."
         ::= { adslAturPerfDataEntry 12 }

         adslAturPerfCurr1DayLofs  OBJECT-TYPE
             SYNTAX      AdslPerfCurrDayCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of the number of seconds when there was Loss
                 of Framing during the current day as measured by
                 adslAturPerfCurr1DayTimeElapsed."
         ::= { adslAturPerfDataEntry 13 }

         adslAturPerfCurr1DayLoss  OBJECT-TYPE
             SYNTAX      AdslPerfCurrDayCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of the number of seconds when there was Loss
                 of Signal during the current day as measured by
                 adslAturPerfCurr1DayTimeElapsed."
         ::= { adslAturPerfDataEntry 14 }

         adslAturPerfCurr1DayLprs  OBJECT-TYPE
             SYNTAX      AdslPerfCurrDayCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of the number of seconds when there was Loss
                 of Power during the current day as measured by
                 adslAturPerfCurr1DayTimeElapsed."
         ::= { adslAturPerfDataEntry 15 }

    adslAturPerfCurr1DayESs OBJECT-TYPE
             SYNTAX      AdslPerfCurrDayCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of Errored Seconds during the current day as
                 measured by adslAturPerfCurr1DayTimeElapsed.
                 The errored second parameter is a count of
                 one-second intervals containing one or more crc
                 anomalies, or one or more los or sef defects."
         ::= { adslAturPerfDataEntry 16 }

         adslAturPerfPrev1DayMoniSecs OBJECT-TYPE
             SYNTAX      INTEGER(0..86400)
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "The amount of time in the previous 1-day interval
                 over which the performance monitoring information
                 is actually counted. This value will be the same as
                 the interval duration except in a situation where
                 performance monitoring data could not be collected
                 for any reason."
         ::= { adslAturPerfDataEntry 17 }

         adslAturPerfPrev1DayLofs  OBJECT-TYPE
             SYNTAX      AdslPerfPrevDayCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of seconds in the interval when there was
                 Loss of Framing within the most recent previous
                 1-day period."
         ::= { adslAturPerfDataEntry 18 }

         adslAturPerfPrev1DayLoss  OBJECT-TYPE
             SYNTAX      AdslPerfPrevDayCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of seconds in the interval when there was
                 Loss of Signal within the most recent previous
                 1-day period."
         ::= { adslAturPerfDataEntry 19 }

         adslAturPerfPrev1DayLprs  OBJECT-TYPE
             SYNTAX      AdslPerfPrevDayCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of seconds in the interval when there was
                 Loss of Power within the most recent previous
                 1-day period."
         ::= { adslAturPerfDataEntry 20 }

         adslAturPerfPrev1DayESs OBJECT-TYPE
             SYNTAX      AdslPerfPrevDayCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of Errored Seconds within the most recent
                 previous 1-day period. The errored second parameter is
                 a count of one-second intervals containing one or more
                 crc anomalies, or one or more los or sef defects."
         ::= { adslAturPerfDataEntry 21 }

         adslAtucIntervalTable   OBJECT-TYPE
             SYNTAX          SEQUENCE OF AdslAtucIntervalEntry
             MAX-ACCESS      not-accessible
             STATUS          current
             DESCRIPTION
                 "This table provides one row for each ATUC
                 performance data collection interval.
                 ADSL physical interfaces are
                 those ifEntries where ifType is equal to adsl(94)."
         ::= { adslMibObjects 8 }

         adslAtucIntervalEntry   OBJECT-TYPE
             SYNTAX          AdslAtucIntervalEntry
             MAX-ACCESS      not-accessible
             STATUS          current
             DESCRIPTION     "An entry in the adslAtucIntervalTable."
             INDEX           { ifIndex, adslAtucIntervalNumber }
         ::= { adslAtucIntervalTable 1 }

         AdslAtucIntervalEntry ::=
             SEQUENCE {
             adslAtucIntervalNumber          INTEGER,
             adslAtucIntervalLofs            PerfIntervalCount,
             adslAtucIntervalLoss            PerfIntervalCount,
             adslAtucIntervalLols            PerfIntervalCount,
             adslAtucIntervalLprs            PerfIntervalCount,
             adslAtucIntervalESs             PerfIntervalCount,
             adslAtucIntervalInits           PerfIntervalCount,
             adslAtucIntervalValidData       TruthValue
             }

         adslAtucIntervalNumber OBJECT-TYPE
             SYNTAX      INTEGER(1..96)
             MAX-ACCESS  not-accessible
             STATUS      current
             DESCRIPTION
                 "Performance Data Interval number 1 is the
                 the most recent previous interval; interval
                 96 is 24 hours ago.  Intervals 2..96 are
                 optional."
         ::= { adslAtucIntervalEntry 1 }

         adslAtucIntervalLofs OBJECT-TYPE
             SYNTAX      PerfIntervalCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of seconds in the interval when there was Loss
                 of Framing."
         ::= { adslAtucIntervalEntry 2 }

         adslAtucIntervalLoss  OBJECT-TYPE
             SYNTAX      PerfIntervalCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of seconds in the interval when there was Loss
                 of Signal."
         ::= { adslAtucIntervalEntry 3 }

         adslAtucIntervalLols  OBJECT-TYPE
             SYNTAX      PerfIntervalCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of seconds in the interval when there was Loss
                 of Link."
         ::= { adslAtucIntervalEntry 4 }

         adslAtucIntervalLprs  OBJECT-TYPE
             SYNTAX      PerfIntervalCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of seconds in the interval when there was Loss
                 of Power."
         ::= { adslAtucIntervalEntry 5 }

         adslAtucIntervalESs OBJECT-TYPE
             SYNTAX      PerfIntervalCount
             UNITS       "seconds"
             MAX-ACCESS  read-only
             STATUS      current
             DESCRIPTION
                 "Count of Errored Seconds in the interval.
                 The errored second parameter is a count of
                 one-se