rfc1515.mib

wm PNE 3.3 source code, running at more than vxworks6.x version.

        MAU-MIB DEFINITIONS ::= BEGIN


        IMPORTS
            Counter                             FROM RFC1155-SMI
            OBJECT-TYPE                         FROM RFC-1212
            mib-2                               FROM RFC1213-MIB
            TRAP-TYPE                           FROM RFC-1215;


        snmpDot3MauMgt OBJECT IDENTIFIER ::= { mib-2 26 }


        --                      References
        --
        -- The following references are used throughout this MIB:
        --
        -- [RFC 1213]
        --    refers to McCloghrie, K., and M. Rose, Editors,
        --    Management Information Base for Network Management
        --    of TCP/IP-based internets: MIB-II, STD 17, RFC 1213,
        --    Hughes LAN Systems, Performance Systems International,
        --    March 1991.
        --
        -- [RFC 1368]
        --    refers to McMaster, D.,  and K. McCloghrie, Editors,
        --    Definitions of Managed Objects for IEEE 802.3 Repeater
        --    Devices, RFC 1368, SynOptics Communications, Hughes
        --    LAN Systems, October 1992.
        --
        -- [IEEE 802.3 MAU Mgt]
        --    refers to IEEE P802.3p, 'Layer Management for 10 Mb/s
        --    Medium Access Unit (MAUs), Section 20,' Draft Supplement
        --    to ANSI/IEEE 802.3, Draft 5, 11 July 1992.


        --                      MIB Groups
        --
        --   The dot3RpMauBasicGroup is mandatory for MAUs attached to
        --     repeaters.
        --   The dot3IfMauBasicGroup is mandatory for MAUs attached to
        --     DTEs (interfaces).
        --   The dot3BroadMauBasicGroup is mandatory for broadband MAUs
        --     attached to DTEs.


        dot3RpMauBasicGroup
            OBJECT IDENTIFIER ::= { snmpDot3MauMgt 1 }
        dot3IfMauBasicGroup
            OBJECT IDENTIFIER ::= { snmpDot3MauMgt 2 }
        dot3BroadMauBasicGroup
            OBJECT IDENTIFIER ::= { snmpDot3MauMgt 3 }


        -- object identifiers for MAU types
        --  (see rpMauType and ifMauType for usage)
        dot3MauType
            OBJECT IDENTIFIER ::= { snmpDot3MauMgt 4 }
        dot3MauTypeAUI        -- no internal MAU, view from AUI
            OBJECT IDENTIFIER ::= { dot3MauType 1 }
        dot3MauType10Base5    -- thick coax MAU (per 802.3 section 8)
            OBJECT IDENTIFIER ::= { dot3MauType 2 }
        dot3MauTypeFoirl      -- FOIRL MAU (per 802.3 section 9.9)
            OBJECT IDENTIFIER ::= { dot3MauType 3 }
        dot3MauType10Base2    -- thin coax MAU (per 802.3 section 10)
            OBJECT IDENTIFIER ::= { dot3MauType 4 }
        dot3MauType10BaseT    -- UTP MAU (per 802.3 section 14)
            OBJECT IDENTIFIER ::= { dot3MauType 5 }
        dot3MauType10BaseFP   -- passive fiber MAU (per 802.3 section 16)
            OBJECT IDENTIFIER ::= { dot3MauType 6 }
        dot3MauType10BaseFB   -- sync fiber MAU (per 802.3 section 17)
            OBJECT IDENTIFIER ::= { dot3MauType 7 }
        dot3MauType10BaseFL   -- async fiber MAU (per 802.3 section 18)
            OBJECT IDENTIFIER ::= { dot3MauType 8 }
        dot3MauType10Broad36  -- broadband DTE MAU (per 802.3 section 11)
            -- note that 10BROAD36 MAUs can be attached to interfaces but
            -- not to repeaters
            OBJECT IDENTIFIER ::= { dot3MauType 9 }


        --
        --                    The Repeater MAU Basic Group
        --
        -- Implementation of the Repeater MAU Basic Group is mandatory
        -- for MAUs attached to repeaters.

        --
        -- The Basic Repeater MAU Table
        --

        rpMauTable OBJECT-TYPE
            SYNTAX    SEQUENCE OF RpMauEntry
            ACCESS    not-accessible
            STATUS    mandatory
            DESCRIPTION
                    "Table of descriptive and status information about
                    the MAU(s) attached to the ports of a repeater."
            ::= { dot3RpMauBasicGroup 1 }

        rpMauEntry OBJECT-TYPE
            SYNTAX    RpMauEntry
            ACCESS    not-accessible
            STATUS    mandatory
            DESCRIPTION
                    "An entry in the table, containing information
                    about a single MAU."
            INDEX    { rpMauGroupIndex, rpMauPortIndex, rpMauIndex }
            ::= { rpMauTable 1 }

        RpMauEntry ::=
            SEQUENCE {
                rpMauGroupIndex
                    INTEGER,
                rpMauPortIndex
                    INTEGER,
                rpMauIndex
                    INTEGER,
                rpMauType
                    OBJECT IDENTIFIER,
                rpMauStatus
                    INTEGER,
                rpMauMediaAvailable
                    INTEGER,
                rpMauMediaAvailableStateExits
                    Counter,
                rpMauJabberState
                    INTEGER,
                rpMauJabberingStateEnters
                    Counter
            }

        rpMauGroupIndex OBJECT-TYPE
            SYNTAX    INTEGER (1..1024)
            ACCESS    read-only
            STATUS    mandatory
            DESCRIPTION
                    "This variable uniquely identifies the repeater
                    group containing the port to which the MAU
                    described by this entry is connected."
            REFERENCE
                    "Reference RFC1368, rptrGroupIndex."
            ::= { rpMauEntry 1 }

        rpMauPortIndex OBJECT-TYPE
            SYNTAX    INTEGER (1..1024)
            ACCESS    read-only
            STATUS    mandatory
            DESCRIPTION
                    "This variable uniquely identifies the repeater
                    port within group rpMauGroupIndex to which the MAU
                    described by this entry is connected."
            REFERENCE
                    "Reference RFC 1368, rptrPortIndex."
            ::= { rpMauEntry 2 }

        rpMauIndex OBJECT-TYPE
            SYNTAX    INTEGER (1..9)
            ACCESS    read-only
            STATUS    mandatory
            DESCRIPTION
                    "This variable uniquely identifies the MAU
                    connected to port rpMauPortIndex within group
                    rpMauGroupIndex that is described by this entry."
            REFERENCE
                    "Reference IEEE 802.3 MAU Mgt, 20.2.3.2, aMAUID."
            ::= { rpMauEntry 3 }

        rpMauType OBJECT-TYPE
            SYNTAX    OBJECT IDENTIFIER
            ACCESS    read-only
            STATUS    mandatory
            DESCRIPTION
                    "This object identifies the 10 Mb/s baseband MAU
                    type.  An initial set of MAU types are defined
                    above.  The assignment of OBJECT IDENTIFIERs to
                    new types of MAUs is managed by the IANA.  If the
                    MAU type is unknown, the object identifier

                        unknownMauType OBJECT IDENTIFIER ::= { 0 0 }

                    is returned.  Note that unknownMauType is a
                    syntactically valid object identifier, and any
                    conformant implementation of ASN.1 and the BER
                    must be able to generate and recognize this
                    value."
            REFERENCE
                    "Reference IEEE 802.3 MAU Mgt, 20.2.3.2,
                    aMAUType."
            ::= { rpMauEntry 4 }

        rpMauStatus OBJECT-TYPE
            SYNTAX    INTEGER {
                          other(1),
                          unknown(2),
                          operational(3),
                          standby(4),
                          shutdown(5),
                          reset(6)
                      }
            ACCESS    read-write
            STATUS    mandatory
            DESCRIPTION
                    "The current state of the MAU.  This object may be
                    implemented as a read-only object by those agents
                    and MAUs that do not implement software control of
                    the MAU state.  Some agents may not support
                    setting the value of this object to some of the
                    enumerated values.

                    The value other(1) is returned if the MAU is in a
                    state other than one of the states 2 through 6.

                    The value unknown(2) is returned when the MAU's
                    true state is unknown; for example, when it is
                    being initialized.

                    A MAU in the operational(3) state is fully
                    functional, operates, and passes signals to its
                    attached DTE or repeater port in accordance to its
                    specification.

                    A MAU in standby(4) state forces DI and CI and the
                    media transmitter to idle.  Standby(4) mode only
                    applies to link type MAUs.  The state of
                    rpMauMediaAvailable is unaffected.

                    A MAU in shutdown(5) state assumes the same
                    condition on DI, CI, and the media transmitter as
                    though it were powered down.  The MAU may return
                    other(1) value for the mauJabber and
                    rpMauMediaAvailable objects when it is in this
                    state.  For an AUI, this state will remove power
                    from the AUI.

                    Setting this variable to the value reset(6) resets
                    the MAU in the same manner as a power-off, power-
                    on cycle of at least one-half second would.  The
                    agent is not required to return the value reset
                    (6).
                    Setting this variable to the value operational(3),
                    standby(4), or shutdown(5) causes the MAU to
                    assume the respective state except that setting a
                    mixing-type MAU or an AUI to standby(4) will cause
                    the MAU to enter the shutdown state."
                REFERENCE
                    "Reference IEEE 802.3 MAU Mgt, 20.2.3.2,
                    aMAUAdminState, and 20.2.3.3, acMAUAdminControl
                    and acResetMAUAction."
            ::= { rpMauEntry 5 }

        rpMauMediaAvailable OBJECT-TYPE
            SYNTAX    INTEGER {
                          other(1),
                          unknown(2),
                          available(3),
                          notAvailable(4),
                          remoteFault(5),
                          invalidSignal(6)
                      }
            ACCESS    read-only
            STATUS    mandatory