rfc2669.mib

wm PNE 3.3 source code, running at more than vxworks6.x version.

             At initial startup, this object has the default value of
             allowProvisioningUpgrade(2)."
        ::= { docsDevSoftware 3 }

docsDevSwOperStatus OBJECT-TYPE
        SYNTAX INTEGER {
            inProgress(1),
            completeFromProvisioning(2),
            completeFromMgt(3),
            failed(4),
            other(5)
        }
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "InProgress(1) indicates that a TFTP download is underway,
             either as a result of a version mismatch at provisioning
             or as a result of a upgradeFromMgt request.
             CompleteFromProvisioning(2) indicates that the last
             software upgrade was a result of version mismatch at
             provisioning. CompleteFromMgt(3) indicates that the last
             software upgrade was a result of setting
             docsDevSwAdminStatus to upgradeFromMgt.
             Failed(4) indicates that the last attempted download
             failed, ordinarily due to TFTP timeout."
        REFERENCE
             "DOCSIS Radio Frequency Interface Specification, Section
             8.2, Downloading Cable Modem Operating Software."
        ::= { docsDevSoftware 4 }

docsDevSwCurrentVers OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "The software version currently operating in this device.
             This object should be in the syntax used by the individual
             vendor to identify software versions.  Any CM MUST return a
             string descriptive of the current software load.  For a
             CMTS, this object SHOULD contain either a human readable
             representation of the vendor specific designation of the
             software for the chassis, or of the software for the
             control processor. If neither of these is  applicable,
             this MUST contain an empty string."
    ::= { docsDevSoftware 5 }


--
-- The following group describes server access and parameters used for
-- initial provisioning and bootstrapping.
--

docsDevServer OBJECT IDENTIFIER ::= { docsDevMIBObjects 4 }

docsDevServerBootState OBJECT-TYPE
        SYNTAX INTEGER {
            operational(1),
            disabled(2),
            waitingForDhcpOffer(3),
            waitingForDhcpResponse(4),
            waitingForTimeServer(5),
            waitingForTftp(6),
            refusedByCmts(7),
            forwardingDenied(8),
            other(9),
            unknown(10)
        }
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "If operational(1), the device has completed loading and
             processing of configuration parameters and the CMTS has
             completed the Registration exchange.
             If disabled(2) then the device was administratively
             disabled, possibly by being refused network access in the
             configuration file.
             If waitingForDhcpOffer(3) then a DHCP Discover has been
             transmitted and no offer has yet been received.
             If waitingForDhcpResponse(4) then a DHCP Request has been
             transmitted and no response has yet been received.
             If waitingForTimeServer(5) then a Time Request has been
             transmitted and no response has yet been received.
             If waitingForTftp(6) then a request to the TFTP parameter
             server has been made and no response received.
             If refusedByCmts(7) then the Registration Request/Response
             exchange with the CMTS failed.
             If forwardingDenied(8) then the registration process
             completed, but the network access option in the received
             configuration file prohibits forwarding. "
        REFERENCE
             "DOCSIS Radio Frequency Interface Specification, Figure
             7-1, CM Initialization Overview."
        ::= { docsDevServer 1 }

docsDevServerDhcp OBJECT-TYPE
        SYNTAX      IpAddress
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The IP address of the DHCP server that assigned an IP
             address to this device. Returns 0.0.0.0 if DHCP was not
             used for IP address assignment."
        ::= { docsDevServer 2 }

docsDevServerTime OBJECT-TYPE
        SYNTAX      IpAddress
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The IP address of the Time server (RFC-868). Returns
             0.0.0.0 if the time server IP address is unknown."
        ::= { docsDevServer 3 }

docsDevServerTftp OBJECT-TYPE
        SYNTAX      IpAddress
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The IP address of the TFTP server responsible for
             downloading provisioning and configuration parameters
             to this device. Returns 0.0.0.0 if the TFTP server
             address is unknown."
        ::= { docsDevServer 4 }

docsDevServerConfigFile OBJECT-TYPE
        SYNTAX      SnmpAdminString
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "The name of the device configuration file read from the
             TFTP server. Returns an empty string if the configuration
             file name is unknown."
        ::= { docsDevServer 5 }

--
--  Event Reporting
--

docsDevEvent OBJECT IDENTIFIER ::= { docsDevMIBObjects 5 }

docsDevEvControl OBJECT-TYPE
        SYNTAX INTEGER {
            resetLog(1),
            useDefaultReporting(2)
        }
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "Setting this object to resetLog(1) empties the event log.
             All data is deleted. Setting it to useDefaultReporting(2)
             returns all event priorities to their factory-default
             reporting. Reading this object always returns
             useDefaultReporting(2)."
        ::= { docsDevEvent 1 }

docsDevEvSyslog OBJECT-TYPE
        SYNTAX      IpAddress
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "The IP address of the Syslog server. If 0.0.0.0, syslog
             transmission is inhibited."
        ::= { docsDevEvent 2 }

docsDevEvThrottleAdminStatus OBJECT-TYPE
        SYNTAX INTEGER {
            unconstrained(1),
            maintainBelowThreshold(2),
            stopAtThreshold(3),
            inhibited(4)
        }
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "Controls the transmission of traps and syslog messages
             with respect to the trap pacing threshold.
             unconstrained(1) causes traps and syslog messages to be
             transmitted without regard to the threshold settings.
             maintainBelowThreshold(2) causes trap transmission and
             syslog messages to be suppressed if the number of traps
             would otherwise exceed the threshold.
             stopAtThreshold(3) causes trap transmission to cease
             at the threshold, and not resume until directed to do so.
             inhibited(4) causes all trap transmission and syslog
             messages to be suppressed.

             A single event is always treated as a single event for
             threshold counting. That is, an event causing both a trap
             and a syslog message is still treated as a single event.

             Writing to this object resets the thresholding state.

             At initial startup, this object has a default value of
             unconstrained(1)."
        ::= { docsDevEvent 3 }

docsDevEvThrottleInhibited OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "If true(1), trap and syslog transmission is currently
             inhibited due to thresholds and/or the current setting of
             docsDevEvThrottleAdminStatus. In addition, this is set to
             true(1) if transmission is inhibited due to no
             syslog (docsDevEvSyslog) or trap (docsDevNmAccessEntry)
             destinations having been set."
        ::= { docsDevEvent 4 }

docsDevEvThrottleThreshold OBJECT-TYPE
        SYNTAX      Unsigned32
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "Number of trap/syslog events per docsDevEvThrottleInterval
             to be transmitted before throttling.

             A single event is always treated as a single event for
             threshold counting. That is, an event causing both a trap
             and a syslog message is still treated as a single event.

             At initial startup, this object returns 0."
        ::= { docsDevEvent 5 }

docsDevEvThrottleInterval OBJECT-TYPE
        SYNTAX      Integer32 (1..2147483647)
        UNITS       "seconds"
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "The interval over which the trap threshold applies.
             At initial startup, this object has a value of 1."

        ::= { docsDevEvent 6 }

--
-- The following table controls the reporting of the various classes of
-- events.
--

docsDevEvControlTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF DocsDevEvControlEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "This table allows control of the reporting of event classes.
        For each event priority, a combination of logging and
        reporting mechanisms may be chosen. The mapping of event types
        to priorities is vendor-dependent. Vendors may also choose to
        allow the user to control that mapping through proprietary
        means."
        ::= {  docsDevEvent 7 }


docsDevEvControlEntry OBJECT-TYPE
        SYNTAX      DocsDevEvControlEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Allows configuration of the reporting mechanisms for a
             particular event priority."
        INDEX { docsDevEvPriority }
        ::= { docsDevEvControlTable 1 }

DocsDevEvControlEntry ::= SEQUENCE {
            docsDevEvPriority        INTEGER,
            docsDevEvReporting       BITS
        }

docsDevEvPriority OBJECT-TYPE
        SYNTAX INTEGER {
            emergency(1),
            alert(2),
            critical(3),
            error(4),
            warning(5),
            notice(6),
            information(7),
            debug(8)
        }
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "The priority level that is controlled by this
             entry. These are ordered from most (emergency) to least
             (debug) critical.  Each event with a CM or CMTS has a
             particular priority level associated with it (as defined
             by the vendor). During normal operation no event more
             critical than notice(6) should be generated. Events between
             warning and emergency should be generated at appropriate
             levels of problems (e.g. emergency when the box is about to
             crash)."
        ::= { docsDevEvControlEntry 1 }

docsDevEvReporting OBJECT-TYPE
        SYNTAX BITS {
            local(0),
            traps(1),
            syslog(2)
        }
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
            "Defines the action to be taken on occurrence of this
             event class. Implementations may not necessarily support
             all options for all event classes, but at minimum must
             allow traps and syslogging to be disabled. If the
             local(0) bit is set, then log to the internal log, if the
             traps(1) bit is set, then generate a trap, if the
             syslog(2) bit is set, then send a syslog message
             (assuming the syslog address is set)."
        ::= { docsDevEvControlEntry 2 }

docsDevEventTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF DocsDevEventEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Contains a log of network and device events that may be
             of interest in fault isolation and troubleshooting."
        ::= {  docsDevEvent 8 }

docsDevEventEntry OBJECT-TYPE
        SYNTAX      DocsDevEventEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
            "Describes a network or device event that may be of
             interest in fault isolation and troubleshooting. Multiple
             sequential identical events are represented by
             incrementing docsDevEvCounts and setting
             docsDevEvLastTime to the current time rather than creating
             multiple rows.

             Entries are created with the first occurrance of an event.
             docsDevEvControl can be used to clear the table.
             Individual events can not be deleted."