english.ini

GTP-USB programmer for Microchip PIC Microcontroller, use for PIC 10,12,14,16,18.

[Main*]
***=Har.>|Nothing|

[Menus*]
MainMenu*=File|Edit|Device|Settings|Language|Help|

M0*=Open|Most Recent Files|Save|Save As|Exit|Update File|Print|
M1*=Fill Buffer|Clear Buffers|
M2*=Read|Verify|Program|Erase|Hardware Test|Detect PIC|
H2*=Read All|Program All|Verify All|Erase All|
M3*=Hardware|Software|
M5*=Parameters|About|
B0*=Code|Data|Setting|ICSP Code|
H0*=Copy|Paste|Cut|Fill Buffer|Mark line|Find|Find next|Select all|
MM*=Marks|Go to mark|Clear all marks|

[pg_llenar*]
***=Fill Buffer|From|To|Value|Cancel|Accept|Insert Selection|

[pg_buscar*]
***=Find|Insert Hexadecimal Bytestream|Cancel|Accept|

[pg_ConfigSoft*]
***=Software Settings|Verify after programming|Ask my confirmation before erasing or programming|Use user device selection|Detect and select device at startup|Update File before programming|Cancel|Accept|

[pg_GuardarComo*]
***=Save as|Cancel|Accept|

[pg_ConfigHardw*]
***=Hardware Settings|Selection of hardware|I/O Bits to port|Save|Save as|Delete|Cancel|Apply edits|
**b=State -|Name|      Use Vpp2|      Use Vdd|      Use Mclr| Blockade configuration|
**g=Save ->
**e=Delete ->

[pg_params*]
****=- Accepted Parameters -|Close|
Tex*=-p           Program|-v           Verify|-a           Automatic device detection|-s           Exit if command finished|-i           Ignore file format using .HEX|-dPICxxxxxx  Force to use a device ||Example :|Program Mihex.hex file using 16F877 and exit when finished.|-p -s -dPIC16F877 c:\Mihex.hex||Example :|Verify using Mihex.hex file by automatic device selection.|-v -a c:\Mis documentos\Mihex.hex|

[pg_about*]
***1=About|Close|
***2=Elena
***3=Author :

[Conf_fc16F6xx*]
***=- Calibration -|Update calibration|
**1=INTOSC Mode/internal MCLR enable

[Acciones*]
***=Cancel|Accept|Close this window when finished|Progress|

[Entorno*]
0*=Program
1*=Read
2*=Verify
3*=Erase
4*=Test
5*=Detect
6*=Hardware test
7*=Opening
8*=Confirm
9*=Device
10*=Checking hardware ......
11*=Hardware Ok.
12*=UNKNOWN
13*=PIC detected
14*=Verifying during programming
15*=Programming
16*=Reading
17*=Verifying
18*=
19*=Ok
20*=Erasing PIC ...
21*=byte
22*=word
23*=PIC is Erased .: Ok
24*=ACK ...........: Ok
25*=Data ..........: Ok

100*=Code ...:
101*=ID .....:
102*=Config. :
103*=Data ...:
104*=
105*=Ins.
106*=Code .....:
107*=ICSP Code :
108*=Data .....:
109*=Config ...:
110*=Executive ICSP code found

[pg_err*]
0*=Not found -> 
1*=Failed to install ->
2*=Failed command line ->
3*=Command line with invalid device ->
4*=Buffer is full
5*=Invalid LPT port
6*=Hardware is not responding
7*=Line
8*=No hexadecimal digit
9*=Found end file
10*=Error in data
11*=ERROR  -> 
12*=Invalid address for the selected device
13*=Writing address 0x
14*=Verifying address 0x
15*=Written : 0x
16*=Verified : 0x
17*=Read : 0x
18*=Error ...
19*=Failed to create hex file
20*=Failed to insert command line or incomplete
21*=Invalid command option
22*=Invalid device
23*=No is answer of  Hardware
24*=LPT number no inserted
25*=Invalid checksum
26*=User break !
27*=PIC part not sopported
28*=Failed to erase pic
29*=No acknowledgement address 0x
30*=Communication "Invalid Checksum"
31*=Hardware not selected
32*=COM interface not selected
33*=Hardware index not selected #
34*=Detected device different from selection
35*=using Vpp2 can make damages
36*=緾ontinue anyway?
37*=Failed to open
38*=Error parameters
39*=Wrinting error parameters
40*=Communication timeout error
41*=Clearing buffers error
42*=No response
43*=PIC Serie not supported by programmer
44*=INFORMATION ->   File size is 
45*=larger than the selected device can store
46*=緾ontinue and truncate data?
47*=Found executive ICSP code in buffer
48*=縐pdate PIC?
49*=The OSCCAL value of the PIC is .... 0x
50*=Use value on buffer 0x
51*=The Bandgap value of the PIC is .... 0x
msg1*=Reading
msg2*=
msg3*=Restoring
msg4*=
Err1*=ERROR -> Failed to restore
Err2*=