config.h

操作系统中的一找你个的相关的淡淡的码源代码

/* config.h - MagicARM2410   configuration header */

/*
modification history
--------------------
*/

/*
This module contains the configuration parameters for the MagicARM2410  BSP.
*/

#ifndef	INCconfigh
#define	INCconfigh

#ifdef __cplusplus
extern "C" {
#endif

/* BSP version/revision identification, before configAll.h */

#define BSP_VER_1_1     1       /* 1.2 is backwards compatible with 1.1 */
#define BSP_VER_1_2     1
#define BSP_VERSION	"1.0"
#define BSP_REV		  "/1"	        /* 0 for first revision */

#include "configAll.h"

#define DBG_BSP

#define FORCE_DEFAULT_BOOT_LINE

#ifdef  FORCE_DEFAULT_BOOT_LINE
#undef  INCLUDE_VWARE_LAUNCH
#else
#define INCLUDE_VWARE_LAUNCH
#endif /* FORCE_DEFAULT_BOOT_LINE */
#define DEFAULT_BOOT_LINE 		  "dmf(0,0)host:vxWorks " \
                                "h=192.168.18.5 " \
                                "e=192.168.18.18:ffffff00 " \
                                "g=192.168.18.1 "  \
                                "u=magic "     \
                                "pw=magic "     \
                                "tn=vxWorks " \
                                "o=dmf"


#define BYTE_ORDER 	_LITTLE_ENDIAN

/* Memory configuration */
#undef	LOCAL_MEM_AUTOSIZE			/* run-time memory sizing */
#define USER_RESERVED_MEM	  0		/* see sysMemTop() */

/*
 * Local-to-Bus memory address constants:
 * the local memory address always appears at 0 locally;
 * it is not dual ported.
 */
#define LOCAL_MEM_LOCAL_ADRS	0x30000000		        /* fixed at 0x30000000 */
#define LOCAL_MEM_BUS_ADRS	  LOCAL_MEM_LOCAL_ADRS	/* fixed at 0x30000000 */
#define LOCAL_MEM_SIZE		    0x04000000		        /* 64 Mbytes */
#define LOCAL_MEM_END_ADRS	  (LOCAL_MEM_LOCAL_ADRS + LOCAL_MEM_SIZE)

/*
 * Boot ROM is an image written into Flash. Part of the Flash can be
 * reserved for boot parameters etc. (see the Flash section below).
 *
 * The following parameters are defined here and in the Makefile.
 * They must be kept synchronized; effectively config.h depends on Makefile.
 * Any changes made here must be made in the Makefile and vice versa.
 *
 * ROM_BASE_ADRS is the base of the Flash ROM/EPROM.
 * ROM_TEXT_ADRS is the entry point of the VxWorks image
 * ROM_SIZE is the size of the part of the Flash ROM/EPROM allocated to
 *		the VxWorks image (block size - size of headers)
 *
 * Two other constants are used:
 * ROM_COPY_SIZE is the size of the part of the ROM to be copied into RAM
 * 		 (e.g. in uncompressed boot ROM)
 * ROM_SIZE_TOTAL is the size of the entire Flash ROM (used in sysPhysMemDesc)
 *
 * The values are given as literals here to make it easier to ensure
 * that they are the same as those in the Makefile.
 */
#define ROM_BASE_ADRS	0x00000000	  /* base of Flash/EPROM */
#define ROM_TEXT_ADRS	ROM_BASE_ADRS	/* code start addr in ROM */
#define ROM_WARM_ADRS	0x00000004	  /* code start addr in ROM */
#define ROM_SIZE	    0x00100000	  /*size of ROM holding VxWorks*/

#define ROM_COPY_SIZE	  ROM_SIZE
#define ROM_SIZE_TOTAL	0x00200000	/* total size of ROM */

#define RAM_LOW_ADRS	0x30010000	  /* VxWorks image entry point */
#define RAM_HIGH_ADRS	0x33000000	  /* RAM address for ROM boot */

#define ROM_MAC_ADRS  0x00040000

#undef  VEC_BASE_ADRS           /*Add  abnormity vector  */
#define VEC_BASE_ADRS   0x30000000

/*
 * Count for a CPU delay loop at the beginning of romInit. There have been
 * reports of problems with certain boards and certain power supplies, and
 * adding a delay at the start of romInit appears to help with this. This
 * value may need tuning for different board/PSU combinations.
 */
#define ____BOOT_DELAY_VALUE	0x1000

/*
 * Flash/NVRAM memory configuration
 *
 * A block of the Flash memory (FLASH_SIZE bytes at FLASH_ADRS) is
 * reserved for non-volatile storage of data.
 *
 * See also integrator.h
 */
#undef   INCLUDE_FLASH
#define  NV_RAM_SIZE           NONE


/* Serial port configuration */
#undef   INCLUDE_TYCODRV_5_2
#define  INCLUDE_SERIAL
#undef	 NUM_TTY
#undef   CONSOLE_TTY
#undef   CONSOLE_BAUD_RATE
#define  NUM_TTY			N_SIO_CHANNELS
#define  CONSOLE_TTY		0	             /* console channel */
#define  CONSOLE_BAUD_RATE	115200	   /* console baud rate */

/*
 * Cache/MMU configuration
 *
 * Note that when MMU is enabled, cache modes are controlled by
 * the MMU table entries in sysPhysMemDesc[], not the cache mode
 * macros defined here.
 */
 
/*
 * Include MMU BASIC and CACHE support for command line and project builds
 */
#define	INCLUDE_MMU
#define	INCLUDE_MMU_BASIC
#define INCLUDE_CACHE_SUPPORT

/*
 * We use the generic architecture libraries, with caches/MMUs present. A
 * call to sysHwInit0() is needed from within usrInit before
 * cacheLibInit() is called.
 */
#ifndef _ASMLANGUAGE
     IMPORT void sysHwInit0 (void);
#endif

#define INCLUDE_SYS_HW_INIT_0
#define SYS_HW_INIT_0()         sysHwInit0()

/*
 * I-cache mode is a bit of an inappropriate concept, but use this.
 */
#undef  USER_I_CACHE_MODE
#define USER_I_CACHE_MODE       CACHE_WRITETHROUGH

/* has to be this. */
#undef  USER_D_CACHE_MODE
#define USER_D_CACHE_MODE       CACHE_COPYBACK


/* Enhanced Network Driver (END) Support */

#ifndef INCLUDE_END
#define INCLUDE_END
#define INCLUDE_FTP_SERVER
#endif


/*
 * Network driver configuration.
 *
 * De-select unused (default) network drivers selected in configAll.h.
 */
#define INCLUDE_NETWORK
/*#undef  INCLUDE_NETWORK*/
/*#undef  INCLUDE_END*/

#undef  STANDALONE_NET
#undef	INCLUDE_EI
#undef	INCLUDE_EX		        
#undef	INCLUDE_ENP		        
#undef	INCLUDE_SM_NET		   
#undef  INCLUDE_LN
#undef	INCLUDE_SM_SEQ_ADDR	 

/* Enhanced Network Driver (END) Support */
#undef  INCLUDE_LED
#ifdef  INCLUDE_LED
#define INCLUDE_LED
#endif

/* WDB configuration. */

#define INCLUDE_NETWORK
#define INCLUDE_WDB
#undef  WDB_COMM_TYPE
#define WDB_COMM_TYPE	WDB_COMM_END 
 


#undef  SYS_CLK_RATE
#define SYS_CLK_RATE		100
/*
 * Interrupt mode - interrupts can be in either preemptive or non-preemptive
 * mode.  For non-preemptive mode, change INT_MODE to INT_NON_PREEMPT_MODEL
 */
#define INT_MODE	INT_PREEMPT_MODEL

/*
 * Enable BSP-configurable interrupt priorities: order of servicing and
 * masking of interrupts will be determined by ambaIntLvlPriMap[] in
 * sysLib.c.  If AMBA_INT_PRIORITY_MAP is not defined, priority of
 * interrupts will be least-significant bit first.
 */


/*
 * miscellaneous definitions
 * Note: ISR_STACK_SIZE is defined here rather than in ../all/configAll.h
 * (as is more usual) because the stack size depends on the interrupt
 * structure of the BSP.
 */
#define ISR_STACK_SIZE	0x800	/* size of ISR stack, in bytes */



/* Optional timestamp support */
#undef	INCLUDE_TIMESTAMP	/* define to include timestamp driver */
/*#define INCLUDE_TIMESTAMP*/

/*#define INCLUDE_RAMDRV Optional TrueFFS support */
#undef  INCLUDE_TFFS      
#ifdef  INCLUDE_TFFS
#define INCLUDE_SHOW_ROUTINES
#define INCLUDE_TFFS_SHOW
#define INCLUDE_DOSFS
#define INCLUDE_DISK_UTIL/*ADD BY supercontrol*/
#define INCLUDE_TL_FTL
#endif /* INCLUDE_TFFS */

#include "s3c2410x.h"

#undef BSP_VTS
#ifdef BSP_VTS

/***************************************************
 * Add these defines for the Validation Test Suite *
 ***************************************************/
#define INCLUDE_SHELL
#undef INCLUDE_RLOGIN
#undef INCLUDE_SHOW_ROUTINES
#undef INCLUDE_NET_SYM_TBL
#define INCLUDE_LOADER

#undef INCLUDE_PING
#undef INCLUDE_NET_SHOW
#endif /*BSP_VTS*/

#define INCLUDE_SHELL 
#ifdef  INCLUDE_SHELL
#define INCLUDE_SYM_TABLE
#define INCLUDE_STANDALONE_SYM_TABLE
#define INCLUDE_LOADER
#define INCLUDE_ELF
#define INCLUDE_STARTUP_SCRIPT
#define INCLUDE_UNLOADER
/*#define INCLUDE_NET_SHOW*/
#endif /* INCLUDE_SHELL */

#undef INCLUDE_WINDML 

#ifdef __cplusplus
}
#endif
#endif  /* INCconfigh */

#if defined(PRJ_BUILD)
#include "prjParams.h"
#endif