📄 attiny25.xml
字号:
<VALUE>0x2C</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 3.0-8.0 MHz; Start-up time PWRDWN/RESET: 1K CK /14 CK + 0 ms; [CKSEL=1100 SUT=10] </TEXT>
</TEXT41>
<TEXT42>
<MASK>0x3F</MASK>
<VALUE>0x3C</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 3.0-8.0 MHz; Start-up time PWRDWN/RESET: 1K CK /14 CK + 4.1 ms; [CKSEL=1100 SUT=11] </TEXT>
</TEXT42>
<TEXT43>
<MASK>0x3F</MASK>
<VALUE>0x0D</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 3.0-8.0 MHz; Start-up time PWRDWN/RESET: 1K CK /14 CK + 65 ms; [CKSEL=1101 SUT=00] </TEXT>
</TEXT43>
<TEXT44>
<MASK>0x3F</MASK>
<VALUE>0x1D</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 3.0-8.0 MHz; Start-up time PWRDWN/RESET: 16K CK/14 CK + 0 ms; [CKSEL=1101 SUT=01] </TEXT>
</TEXT44>
<TEXT45>
<MASK>0x3F</MASK>
<VALUE>0x2D</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 3.0-8.0 MHz; Start-up time PWRDWN/RESET: 16K CK/14 CK + 4.1 ms; [CKSEL=1101 SUT=10] </TEXT>
</TEXT45>
<TEXT46>
<MASK>0x3F</MASK>
<VALUE>0x3D</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 3.0-8.0 MHz; Start-up time PWRDWN/RESET: 16K CK/14 CK + 65 ms; [CKSEL=1101 SUT=11] </TEXT>
</TEXT46>
<TEXT47>
<MASK>0x3F</MASK>
<VALUE>0x0E</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 8.0- MHz; Start-up time PWRDWN/RESET: 258 CK/14 CK + 4.1 ms; [CKSEL=1110 SUT=00] </TEXT>
</TEXT47>
<TEXT48>
<MASK>0x3F</MASK>
<VALUE>0x1E</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 8.0- MHz; Start-up time PWRDWN/RESET: 258 CK/14 CK + 65 ms; [CKSEL=1110 SUT=01] </TEXT>
</TEXT48>
<TEXT49>
<MASK>0x3F</MASK>
<VALUE>0x2E</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 8.0- MHz; Start-up time PWRDWN/RESET: 1K CK /14 CK + 0 ms; [CKSEL=1110 SUT=10] </TEXT>
</TEXT49>
<TEXT50>
<MASK>0x3F</MASK>
<VALUE>0x3E</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 8.0- MHz; Start-up time PWRDWN/RESET: 1K CK /14 CK + 4.1 ms; [CKSEL=1110 SUT=11] </TEXT>
</TEXT50>
<TEXT51>
<MASK>0x3F</MASK>
<VALUE>0x0F</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 8.0- MHz; Start-up time PWRDWN/RESET: 1K CK /14 CK + 65 ms; [CKSEL=1111 SUT=00] </TEXT>
</TEXT51>
<TEXT52>
<MASK>0x3F</MASK>
<VALUE>0x1F</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 8.0- MHz; Start-up time PWRDWN/RESET: 16K CK/14 CK + 0 ms; [CKSEL=1111 SUT=01] </TEXT>
</TEXT52>
<TEXT53>
<MASK>0x3F</MASK>
<VALUE>0x2F</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 8.0- MHz; Start-up time PWRDWN/RESET: 16K CK/14 CK + 4.1 ms; [CKSEL=1111 SUT=10] </TEXT>
</TEXT53>
<TEXT54>
<MASK>0x3F</MASK>
<VALUE>0x3F</VALUE>
<TEXT>Ext. Crystal Osc.; Frequency 8.0- MHz; Start-up time PWRDWN/RESET: 16K CK/14 CK + 65 ms; [CKSEL=1111 SUT=11] </TEXT>
</TEXT54>
<FUSE0>
<NAME>CKSEL0</NAME>
<TEXT>Select Clock source</TEXT>
<DEFAULT>0</DEFAULT>
</FUSE0>
<FUSE1>
<NAME>CKSEL1</NAME>
<TEXT>Select Clock source</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE1>
<FUSE2>
<NAME>CKSEL2</NAME>
<TEXT>Select Clock source</TEXT>
<DEFAULT>0</DEFAULT>
</FUSE2>
<FUSE3>
<NAME>CKSEL3</NAME>
<TEXT>Select Clock source</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE3>
<FUSE4>
<NAME>SUT0</NAME>
<TEXT>Select start-up time</TEXT>
<DEFAULT>0</DEFAULT>
</FUSE4>
<FUSE5>
<NAME>SUT1</NAME>
<TEXT>Select start-up time</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE5>
<FUSE6>
<NAME>CKOUT</NAME>
<TEXT>Clock Output Enable</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE6>
<FUSE7>
<NAME>CKDIV8</NAME>
<TEXT>Divide clock by 8</TEXT>
<DEFAULT>0</DEFAULT>
</FUSE7>
</LOW>
<HIGH>
<NMB_TEXT>13</NMB_TEXT>
<NMB_FUSE_BITS>8</NMB_FUSE_BITS>
<TEXT1>
<MASK>0x80</MASK>
<VALUE>0x00</VALUE>
<TEXT>Reset Disabled (Enable PB5 as i/o pin); [RSTDISBL=0]</TEXT>
</TEXT1>
<TEXT2>
<MASK>0x40</MASK>
<VALUE>0x00</VALUE>
<TEXT>Debug Wire enable; [DWEN=0]</TEXT>
</TEXT2>
<TEXT3>
<MASK>0x20</MASK>
<VALUE>0x00</VALUE>
<TEXT>Serial program downloading (SPI) enabled; [SPIEN=0]</TEXT>
</TEXT3>
<TEXT4>
<MASK>0x10</MASK>
<VALUE>0x00</VALUE>
<TEXT>Watch-dog Timer always on; [WDTON=0]</TEXT>
</TEXT4>
<TEXT5>
<MASK>0x08</MASK>
<VALUE>0x00</VALUE>
<TEXT>Preserve EEPROM memory through the Chip Erase cycle; [EESAVE=0]</TEXT>
</TEXT5>
<TEXT6>
<MASK>0x07</MASK>
<VALUE>0x04</VALUE>
<TEXT>Brown-out detection level at VCC=4.3 V; [BODLEVEL=100] </TEXT>
</TEXT6>
<TEXT7>
<MASK>0x07</MASK>
<VALUE>0x05</VALUE>
<TEXT>Brown-out detection level at VCC=2.7 V; [BODLEVEL=101] </TEXT>
</TEXT7>
<TEXT8>
<MASK>0x07</MASK>
<VALUE>0x03</VALUE>
<TEXT>Brown-out detection level at VCC=2.3 V; [BODLEVEL=011] </TEXT>
</TEXT8>
<TEXT9>
<MASK>0x07</MASK>
<VALUE>0x02</VALUE>
<TEXT>Brown-out detection level at VCC=2.2 V; [BODLEVEL=010] </TEXT>
</TEXT9>
<TEXT10>
<MASK>0x07</MASK>
<VALUE>0x00</VALUE>
<TEXT>Brown-out detection level at VCC=2.0 V; [BODLEVEL=000] </TEXT>
</TEXT10>
<TEXT11>
<MASK>0x07</MASK>
<VALUE>0x01</VALUE>
<TEXT>Brown-out detection level at VCC=1.9 V; [BODLEVEL=001] </TEXT>
</TEXT11>
<TEXT12>
<MASK>0x07</MASK>
<VALUE>0x06</VALUE>
<TEXT>Brown-out detection level at VCC=1.8 V; [BODLEVEL=110] </TEXT>
</TEXT12>
<TEXT13>
<MASK>0x07</MASK>
<VALUE>0x07</VALUE>
<TEXT>Brown-out detection disabled; [BODLEVEL=111] </TEXT>
</TEXT13>
<FUSE0>
<NAME>BODLEVEL0</NAME>
<TEXT>Brown-out Detector trigger level</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE0>
<FUSE1>
<NAME>BODLEVEL1</NAME>
<TEXT>Brown-out Detector trigger level</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE1>
<FUSE2>
<NAME>BODLEVEL2</NAME>
<TEXT>Brown-out Detector trigger level</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE2>
<FUSE3>
<NAME>EESAVE</NAME>
<TEXT>EEPROM memory is preserved through the Chip Erase</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE3>
<FUSE4>
<NAME>WDTON</NAME>
<TEXT>Watchdog Timer always on</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE4>
<FUSE5>
<NAME>SPIEN</NAME>
<TEXT>Enable Serial Program and Data Downloading</TEXT>
<DEFAULT>0</DEFAULT>
</FUSE5>
<FUSE6>
<NAME>DWEN</NAME>
<TEXT>DebugWIRE Enable</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE6>
<FUSE7>
<NAME>RSTDISBL</NAME>
<TEXT>External Reset disable</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE7>
</HIGH>
<EXTENDED>
<FUSE0>
<NAME>SELFPRGEN</NAME>
<TEXT>Self-Programming Enable</TEXT>
<DEFAULT>1</DEFAULT>
</FUSE0>
<NMB_TEXT>1</NMB_TEXT>
<NMB_FUSE_BITS>1</NMB_FUSE_BITS>
<TEXT1>
<MASK>0x01</MASK>
<VALUE>0x00</VALUE>
<TEXT>Self Programming enable; [SELFPRGEN=0]</TEXT>
</TEXT1>
</EXTENDED>
</FUSE>
</AVRPART>
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -