sdcmd.h

合众达的DM642示例工程

/*--------------File Info-------------------------------------------------------------------------------
** File name:			sddriver.c
** Last modified Date:	2005-1-6
** Last Version:		V1.0
** Descriptions:		sd 卡驱动软件包: SD卡物理层 ---- SD卡SPI模式支持的命令(头文件) 
**						Soft Packet of SD Card Driver: commands that sd card supported in spi mode(header file)
**
**------------------------------------------------------------------------------------------------------
** Created by:			Ming Yuan Zheng
** Created date:		2005-1-6
** Version:				V1.0
** Descriptions:		The original version
**
**------------------------------------------------------------------------------------------------------
** Modified by:			
** Modified date:		
** Version:				
** Descriptions:		
**
**------------------------------------------------------------------------------------------------------
** Modified by: 
** Modified date:
** Version:	
** Descriptions: 
**
********************************************************************************************************/

/*
 *******************************************************
	
		SD 卡的相关命令与响应宏定义
	
 *******************************************************
*/
#include <csl_stdinc.h>
/* 命令响应定义 define command's response */
#define R1 1
#define R1B 2
#define R2 3
#define R3 4

/* R1和R2高字节错误码 R1 and upper byte of R2 error code */
#define MSK_IDLE          		  0x01
#define MSK_ERASE_RST     		  0x02
#define MSK_ILL_CMD       		  0x04
#define MSK_CRC_ERR       		  0x08
#define MSK_ERASE_SEQ_ERR 		  0x10
#define MSK_ADDR_ERR      		  0x20
#define MSK_PARAM_ERR     		  0x40

/* R2低字节错误码 lower byte of R2 error code */
#define MSK_TOK_ERROR             0x01
#define MSK_TOK_CC_ERROR          0x02
#define MSK_TOK_ECC_FAILED        0x04
#define MSK_TOK_CC_OUTOFRANGE     0x08
#define MSK_TOK_CC_LOCKED         0x10



/* 数据令牌 Data Tokens */
#define SD_TOK_READ_STARTBLOCK    0xFE
#define SD_TOK_WRITE_STARTBLOCK   0xFE
#define SD_TOK_READ_STARTBLOCK_M  0xFE
#define SD_TOK_WRITE_STARTBLOCK_M 0xFC
#define SD_TOK_STOP_MULTI         0xFD

/* 数据响应令牌 Data Response Tokens */
#define SD_RESP_DATA_MSK		  0x0F		//数据响应掩码
#define SD_RESP_DATA_ACCETPTED	  0x05		//数据被接受
#define SD_RESP_DATA_REJECT_CRC	  0x0B      //由于CRC错误而被拒绝
#define SD_RESP_DATA_REJECT_WRITE 0x0D		//由于写错误而被拒绝

/* 等待类型 Wait Type */
#define SD_WAIT_READ			  0x00		//读等待
#define SD_WAIT_WRITE			  0x01		//写等待
#define SD_WAIT_ERASE		 	  0x02		//擦除等待


#define SD_READREG_TIMEOUT		  8


/*
*********************************************

     SD卡SPI模式下命令集

*********************************************
*/

/******************************** 基本命令集 Basic command set **************************/
/* 复位SD 卡 Reset cards to idle state */
#define CMD0 0
#define CMD0_R R1

/* 读OCR寄存器 Read the OCR (MMC mode, do not use for SD cards) */
#define CMD1 1
#define CMD1_R R1

/* 读CSD寄存器 Card sends the CSD */
#define CMD9 9
#define CMD9_R R1

/* 读CID寄存器 Card sends CID */
#define CMD10 10
#define CMD10_R R1

/* 停止读多块时的数据传输 Stop a multiple block (stream) read/write operation */
#define CMD12 12
#define CMD12_R R1B

/* 读 Card_Status 寄存器 Get the addressed card's status register */
#define CMD13 13
#define CMD13_R R2

/***************************** 块读命令集 Block read commands **************************/

/* 设置块的长度 Set the block length */
#define CMD16 16
#define CMD16_R R1

/* 读单块 Read a single block */
#define CMD17 17
#define CMD17_R R1

/* 读多块,直至主机发送CMD12为止 Read multiple blocks until a CMD12 */
#define CMD18 18
#define CMD18_R R1

/***************************** 块写命令集 Block write commands *************************/
/* 写单块 Write a block of the size selected with CMD16 */
#define CMD24 24
#define CMD24_R R1

/* 写多块 Multiple block write until a CMD12 */
#define CMD25 25
#define CMD25_R R1

/* 写CSD寄存器 Program the programmable bits of the CSD */
#define CMD27 27
#define CMD27_R R1

/***************************** 写保护 Write protection *****************************/
/* Set the write protection bit of the addressed group */
#define CMD28 28
#define CMD28_R R1B

/* Clear the write protection bit of the addressed group */
#define CMD29 29
#define CMD29_R R1B

/* Ask the card for the status of the write protection bits */
#define CMD30 30
#define CMD30_R R1

/***************************** 擦除命令 Erase commands *******************************/
/* 设置擦除块的起始地址 Set the address of the first write block to be erased */
#define CMD32 32
#define CMD32_R R1

/* 设置擦除块的终止地址 Set the address of the last write block to be erased */
#define CMD33 33
#define CMD33_R R1

/* 擦除所选择的块 Erase the selected write blocks */
#define CMD38 38
#define CMD38_R R1B

/***************************** 锁卡命令 Lock Card commands ***************************/
/* 设置/复位密码或上锁/解锁卡 Set/reset the password or lock/unlock the card */
#define CMD42 42
#define CMD42_R	R1B
/* Commands from 42 to 54, not defined here */

/***************************** 应用命令 Application-specific commands ****************/
/* 禁止下一个命令为应用命令  Flag that the next command is application-specific */
#define CMD55 55
#define CMD55_R R1

/* 应用命令的通用I/O  General purpose I/O for application-specific commands */
#define CMD56 56
#define CMD56_R R1

/* 读OCR寄存器  Read the OCR (SPI mode only) */
#define CMD58 58
#define CMD58_R R3

/* 使能或禁止 CRC Turn CRC on or off */
#define CMD59 59
#define CMD59_R R1

/***************************** 应用命令 Application-specific commands ***************/
/* 获取 SD Status寄存器 Get the SD card's status */
#define ACMD13 13
#define ACMD13_R R2

/* 得到已写入卡中的块的个数 Get the number of written write blocks (Minus errors ) */
#define ACMD22 22
#define ACMD22_R R1

/* 在写之前,设置预先擦除的块的个数 Set the number of write blocks to be pre-erased before writing */
#define ACMD23 23
#define ACMD23_R R1

/* 读取OCR寄存器 Get the card's OCR (SD mode) */
#define ACMD41 41
#define ACMD41_R R1

/* 连接/断开CD/DATA[3]引脚上的上拉电阻 Connect or disconnect the 50kOhm internal pull-up on CD/DAT[3] */
#define ACMD42 42
#define ACMD42_R R1

/* 读取SCR寄存器 Get the SD configuration register */
#define ACMD51 51
#define ACMD51_R R1



Uint8 SD_SendCmd(Uint8 cmd, Uint8 *param, Uint8 resptype, Uint8 *resp);  // 一个SPI命令 
void SD_PackParam(Uint8 *parameter, Uint32 value);						 // 封装参数
Uint8 SD_BlockCommand(Uint8 cmd, Uint8 resptype, Uint32 parameter);		 // 块命令 

	
Uint8 SD_ResetSD(void);											// 复位SD卡

Uint8 SD_ReadCSD(Uint8 csdlen, Uint8 *recbuf);					// 读CSD 			read CSD register
Uint8 SD_ReadCID(Uint8 cidlen, Uint8 *recbuf);					// 读CID			read CID register
Uint8 SD_StopTransmission(void);								// 停止传输			

Uint8 SD_ReadCard_Status(Uint8 len, Uint8 *buffer);				// 读Card Status	read Card Status register
Uint8 SD_SetBlockLen(Uint32 length);							// 设置块长度

Uint8 SD_ReadSingleBlock(Uint32 blockaddr);						// 读单块
Uint8 SD_ReadMultipleBlock(Uint32 blockaddr);					// 读多块

Uint8 SD_WriteSingleBlock(Uint32 blockaddr);					// 写单块
Uint8 SD_WriteMultipleBlock(Uint32 blockaddr);					// 写多块 


Uint8 SD_ProgramCSD(Uint8 len, Uint8 *buff);					// 写CSD寄存器  	write CSD register 

Uint8 SD_EraseStartBlock(Uint32 startblock);					// 擦块起始地址
Uint8 SD_EraseEndBlock(Uint32 endblock);						// 擦块终止地址
Uint8 SD_EraseSelectedBlock(void);								// 擦除所选的块


Uint8 SD_ReadOCR(Uint8 ocrlen,Uint8 *recbuf);					// 读OCR			read OCR register
Uint8 SD_EnableCRC(Uint8 bEnable);								// 使能CRC校验		enable CRC


// 特殊应用命令
Uint8 SD_ReadSD_Status(Uint8 sdslen, Uint8 *recbuf);			// 读SD_Status  read SD_Status 
Uint8 SD_GetNumWRBlcoks(Uint32 *blocknum);						// 得到正确写入块数
Uint8 SD_ReadSCR(Uint8 scrlen, Uint8 *recbuf);					// 读SCR 		read SCR register


// 数据流函数
Uint8 SD_ReadRegister(Uint32 len, Uint8 *recbuf);						// 读数据
Uint8 SD_ReadBlockData(Uint32 len, Uint8 *recbuf);						// 读块数据
Uint8 SD_WriteBlockData(Uint8 bmulti, Uint32 len, Uint8 *sendbuf);		// 写块数据

// 其它函数
void SD_StopMultiToken(void);									// 停止多块写令牌
Uint8 SD_WaitBusy(Uint8 waittype);								// 忙
void SD_SPIDelay(Uint8 value);									// 发生SPI时钟