snmp-target-mib.txt

架設ROSE私服必備之物 ROSE數據庫

SNMP-TARGET-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY,
    OBJECT-TYPE,
    snmpModules,
    Counter32,
    Integer32

        FROM SNMPv2-SMI

    TEXTUAL-CONVENTION,
    TDomain,
    TAddress,
    TimeInterval,
    RowStatus,
    StorageType,
    TestAndIncr
        FROM SNMPv2-TC

    SnmpSecurityModel,
    SnmpMessageProcessingModel,
    SnmpSecurityLevel,
    SnmpAdminString
        FROM SNMP-FRAMEWORK-MIB

    MODULE-COMPLIANCE,
    OBJECT-GROUP
        FROM SNMPv2-CONF;

snmpTargetMIB MODULE-IDENTITY
    LAST-UPDATED "9808040000Z"
    ORGANIZATION "IETF SNMPv3 Working Group"
    CONTACT-INFO
        "WG-email:   [e-mail]
         Subscribe:  [e-mail]
                     In message body:  subscribe snmpv3

         Chair:      Russ Mundy

                     Trusted Information Systems
         Postal:     3060 Washington Rd
                     Glenwood MD 21738
                     USA
         EMail:      [e-mail]
         Phone:      [phone]

         Co-editor:  David B. Levi
                     SNMP Research, Inc.
         Postal:     3001 Kimberlin Heights Road
                     Knoxville, TN 37920-9716
         EMail:      [e-mail]
         Phone:      [phone]

         Co-editor:  Paul Meyer
                     Secure Computing Corporation
         Postal:     2675 Long Lake Road
                     Roseville, MN 55113
         EMail:      [e-mail]
         Phone:      [phone]

         Co-editor:  Bob Stewart
                     Cisco Systems, Inc.
         Postal:     170 West Tasman Drive
                     San Jose, CA 95134-1706
         EMail:      [e-mail]
         Phone:      [phone]"
    DESCRIPTION
        "This MIB module defines MIB objects which provide
         mechanisms to remotely configure the parameters used
         by an SNMP entity for the generation of SNMP messages."
    REVISION    "9808040000Z"
    DESCRIPTION "Clarifications, published as
                 RFC2573."
    REVISION    "9707140000Z"
    DESCRIPTION "The initial revision, published as RFC2273."
    ::= { snmpModules 12 }

snmpTargetObjects       OBJECT IDENTIFIER ::= { snmpTargetMIB 1 }
snmpTargetConformance   OBJECT IDENTIFIER ::= { snmpTargetMIB 3 }

SnmpTagValue ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "255a"
    STATUS       current
    DESCRIPTION
        "An octet string containing a tag value.
         Tag values are preferably in human-readable form.

         To facilitate internationalization, this information
         is represented using the ISO/IEC IS 10646-1 character
         set, encoded as an octet string using the UTF-8
         character encoding scheme described in RFC 2279.

         Since additional code points are added by amendments
         to the 10646 standard from time to time,
         implementations must be prepared to encounter any code
         point from 0x00000000 to 0x7fffffff.

         The use of control codes should be avoided, and certain
         control codes are not allowed as described below.

         For code points not directly supported by user
         interface hardware or software, an alternative means
         of entry and display, such as hexadecimal, may be
         provided.

         For information encoded in 7-bit US-ASCII, the UTF-8
         representation is identical to the US-ASCII encoding.

         Note that when this TC is used for an object that
         is used or envisioned to be used as an index, then a
         SIZE restriction must be specified so that the number
         of sub-identifiers for any object instance does not
         exceed the limit of 128, as defined by [RFC1905].

         An object of this type contains a single tag value
         which is used to select a set of entries in a table.

         A tag value is an arbitrary string of octets, but
         may not contain a delimiter character.  Delimiter
         characters are defined to be one of the following:

             -  An ASCII space character (0x20).

             -  An ASCII TAB character (0x09).

             -  An ASCII carriage return (CR) character (0x0D).

             -  An ASCII line feed (LF) character (0x0B).

         Delimiter characters are used to separate tag values
         in a tag list.  An object of this type may only
         contain a single tag value, and so delimiter
         characters are not allowed in a value of this type.

         Some examples of valid tag values are:

             - 'acme'

             - 'router'

             - 'host'

         The use of a tag value to select table entries is
         application and MIB specific."
    SYNTAX       OCTET STRING (SIZE (0..255))

SnmpTagList ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "255a"
    STATUS       current
    DESCRIPTION
        "An octet string containing a list of tag values.
         Tag values are preferably in human-readable form.

         To facilitate internationalization, this information
         is represented using the ISO/IEC IS 10646-1 character
         set, encoded as an octet string using the UTF-8
         character encoding scheme described in RFC 2279.

         Since additional code points are added by amendments
         to the 10646 standard from time to time,
         implementations must be prepared to encounter any code
         point from 0x00000000 to 0x7fffffff.

         The use of control codes should be avoided, except as
         described below.

         For code points not directly supported by user
         interface hardware or software, an alternative means
         of entry and display, such as hexadecimal, may be
         provided.

         For information encoded in 7-bit US-ASCII, the UTF-8
         representation is identical to the US-ASCII encoding.

         An object of this type contains a list of tag values
         which are used to select a set of entries in a table.

         A tag value is an arbitrary string of octets, but
         may not contain a delimiter character.  Delimiter
         characters are defined to be one of the following:

             -  An ASCII space character (0x20).

             -  An ASCII TAB character (0x09).

             -  An ASCII carriage return (CR) character (0x0D).

             -  An ASCII line feed (LF) character (0x0B).

         Delimiter characters are used to separate tag values
         in a tag list.  Only a single delimiter character may
         occur between two tag values.  A tag value may not
         have a zero length.  These constraints imply certain
         restrictions on the contents of this object:

             - There cannot be a leading or trailing delimiter
               character.

             - There cannot be multiple adjacent delimiter
               characters.

         Some examples of valid tag lists are:

             - An empty string

             - 'acme router'

             - 'host managerStation'

         Note that although a tag value may not have a length of
         zero, an empty string is still valid.  This indicates
         an empty list (i.e. there are no tag values in the list).

         The use of the tag list to select table entries is
         application and MIB specific.  Typically, an application
         will provide one or more tag values, and any entry
         which contains some combination of these tag values
         will be selected."
    SYNTAX       OCTET STRING (SIZE (0..255))

--
--
-- The snmpTargetObjects group
--
--

snmpTargetSpinLock OBJECT-TYPE
    SYNTAX      TestAndIncr
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This object is used to facilitate modification of table
         entries in the SNMP-TARGET-MIB module by multiple

         managers.  In particular, it is useful when modifying
         the value of the snmpTargetAddrTagList object.

         The procedure for modifying the snmpTargetAddrTagList
         object is as follows:

             1.  Retrieve the value of snmpTargetSpinLock and
                 of snmpTargetAddrTagList.

             2.  Generate a new value for snmpTargetAddrTagList.

             3.  Set the value of snmpTargetSpinLock to the
                 retrieved value, and the value of
                 snmpTargetAddrTagList to the new value.  If
                 the set fails for the snmpTargetSpinLock
                 object, go back to step 1."
    ::= { snmpTargetObjects 1 }

snmpTargetAddrTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF SnmpTargetAddrEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table of transport addresses to be used in the generation
         of SNMP messages."
    ::= { snmpTargetObjects 2 }

snmpTargetAddrEntry OBJECT-TYPE
    SYNTAX      SnmpTargetAddrEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A transport address to be used in the generation
         of SNMP operations.

         Entries in the snmpTargetAddrTable are created and
         deleted using the snmpTargetAddrRowStatus object."
    INDEX { IMPLIED snmpTargetAddrName }
    ::= { snmpTargetAddrTable 1 }

SnmpTargetAddrEntry ::= SEQUENCE {
    snmpTargetAddrName         SnmpAdminString,
    snmpTargetAddrTDomain      TDomain,
    snmpTargetAddrTAddress     TAddress,
    snmpTargetAddrTimeout      TimeInterval,
    snmpTargetAddrRetryCount   Integer32,
    snmpTargetAddrTagList      SnmpTagList,
    snmpTargetAddrParams       SnmpAdminString,
    snmpTargetAddrStorageType  StorageType,
    snmpTargetAddrRowStatus    RowStatus
}

snmpTargetAddrName OBJECT-TYPE
    SYNTAX      SnmpAdminString (SIZE(1..32))
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The locally arbitrary, but unique identifier associated
         with this snmpTargetAddrEntry."
    ::= { snmpTargetAddrEntry 1 }

snmpTargetAddrTDomain OBJECT-TYPE
    SYNTAX      TDomain
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
        "This object indicates the transport type of the address
         contained in the snmpTargetAddrTAddress object."
    ::= { snmpTargetAddrEntry 2 }

snmpTargetAddrTAddress OBJECT-TYPE
    SYNTAX      TAddress
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
        "This object contains a transport address.  The format of
         this address depends on the value of the
         snmpTargetAddrTDomain object."
    ::= { snmpTargetAddrEntry 3 }

snmpTargetAddrTimeout OBJECT-TYPE
    SYNTAX      TimeInterval
    MAX-ACCESS  read-create