44btest.c~

这是在linux下

#include "../inc/44b.h"
#include "../inc/44blib.h"
#include "../inc/def.h"

int count=0;
#define IICBUFSIZE 0x20
#define WRDATA	    (1)
#define POLLACK     (2)
#define RDDATA	    (3)
#define SETRDADDR   (4)

U8 _iicData[IICBUFSIZE];
volatile int _iicDataCount;
volatile int _iicStatus;
volatile int _iicMode;
int _iicPt;

void Wr24C040(U32 slvAddr,U32 addr,U8 data);
void Rd24C040(U32 slvAddr,U32 addr,U8 *data);
void  IicPoll(void);


void Main(void)
{
    unsigned int i,j;
    static U8 data[256];
    
    SystemClockInit();			//╰参牧﹍て
	MemCfgInit();				//砞竚獶Cache跋
	PortInit();					//狠﹍て

	Uart_Init(0,38400);
	CacheEnable();				//Cache璓
    Led_Display(0x07);
    
    Uart_Printf("[IIC Test using KS24C02 no int]\n");
    
    rIICCON=(1<<7)|(0<<6)|(1<<5)|(0xf);
    //Enable interrupt, IICCLK=MCLK/16, Enable ACK
    //40Mhz/16/(15+1) = 257Khz	
    rIICADD=0x10;   // S3C44B0X slave address

    rIICSTAT=0x10;

    Uart_Printf("Write test data into KS24C080\n");
    
    for(i=0;i<256;i++)
	 Wr24C040(0xa0,(U8)i,i);
    for(i=0;i<256;i++)
	 data[i]=0;

    Uart_Printf("Read test data from KS24C080\n");
    
    for(i=0;i<256;i++)
	  Rd24C040(0xa1,(U8)i,&(data[i])); 

    for(i=0;i<16;i++)
    {
	  for(j=0;j<16;j++)
	    Uart_Printf("%2x ",data[i*16+j]);
	  Uart_Printf("\n");
    }	
    
    Timer_Init();
  
    while(1)
    {
     if(count==25)
      {
         Led_Display(0x0);
      }else if(count==50)
      {
         Led_Display(0x1);
      }else if(count==75)
      {
         Led_Display(0x2);
      }else if(count==100)
      {
         Led_Display(0x4);
      }else if(count==125)
      {
         Led_Display(0x7);
         count= 0;
      }
    }  
}

void Run_LicPoll(void)
{
   if(rIICCON & 0x10)
     IicPoll();
}

void  IicPoll(void)
{
    U32 iicSt,i;

    iicSt=rIICSTAT; 
    if(iicSt&0x8){} // when bus arbitration is failed.
    if(iicSt&0x4){} // when a slave address is matched with IICADD
    if(iicSt&0x2){} // when a slave address is 0000000b
    if(iicSt&0x1){} // when ACK isn't received

    switch(_iicMode)
    {
	case POLLACK:
	    _iicStatus=iicSt;
	    break;

	case RDDATA:
	    if((_iicDataCount--)==0)
	    {
		_iicData[_iicPt++]=rIICDS;
	    
		rIICSTAT=0x90;  //stop MasRx condition 
		rIICCON=0xaf;   //resumes IIC operation.
		Delay(1);	//wait until stop condtion is in effect.
				//too long time... 
		//The pending bit will not be set after issuing stop condition.
		break;    
	    }	     
	    _iicData[_iicPt++]=rIICDS;
				//The last data has to be read with no ack.
	    if((_iicDataCount)==0)
		rIICCON=0x2f;	//resumes IIC operation with NOACK.  
	    else 
		rIICCON=0xaf;	//resumes IIC operation with ACK
	    break;

	case WRDATA:
	    if((_iicDataCount--)==0)
	    {
		rIICSTAT=0xd0;	//stop MasTx condition 
		rIICCON=0xaf;	//resumes IIC operation.
		Delay(1);	//wait until stop condtion is in effect.
		//The pending bit will not be set after issuing stop condition.
		break;    
	    }
	    rIICDS=_iicData[_iicPt++];  //_iicData[0] has dummy.
	    for(i=0;i<10;i++);	    //for setup time until rising edge of IICSCL
	    rIICCON=0xaf;	    //resumes IIC operation.
	    break;

	case SETRDADDR:
	    //Uart_Printf("[S%d]",_iicDataCount);
	    if((_iicDataCount--)==0)
	    {
		break;  //IIC operation is stopped because of IICCON[4]    
	    }
	    rIICDS=_iicData[_iicPt++];
	    for(i=0;i<10;i++);  //for setup time until rising edge of IICSCL
	    rIICCON=0xaf;	    //resumes IIC operation.
	    break;

	default:
	    break;	  
    }
}

/******************************************************************/


void Wr24C040(U32 slvAddr,U32 addr,U8 data)
{
    _iicMode=WRDATA;
    _iicPt=0;
    _iicData[0]=(U8)addr;
    _iicData[1]=data;
    _iicDataCount=2;
    
    rIICDS=slvAddr;//0xa0
    rIICSTAT=0xf0; //MasTx,Start
    //Clearing the pending bit isn't needed because the pending bit has been cleared.
    while(_iicDataCount!=-1)
      Run_LicPoll();

    _iicMode=POLLACK;

    while(1)
    {
	rIICDS=slvAddr;
	_iicStatus=0x100;
	rIICSTAT=0xf0; //MasTx,Start
	rIICCON=0xaf;  //resumes IIC operation. 
	while(_iicStatus==0x100)
	  Run_LicPoll();
	if(!(_iicStatus&0x1))
	    break; // when ACK is received
    }
    rIICSTAT=0xd0;  //stop MasTx condition 
    rIICCON=0xaf;   //resumes IIC operation. 
    Delay(1);	    //wait until stop condtion is in effect.

    //write is completed.
}
	
void Rd24C040(U32 slvAddr,U32 addr,U8 *data)
{
    _iicMode=SETRDADDR;
    _iicPt=0;
    _iicData[0]=(U8)addr;
    _iicDataCount=1;

    rIICDS=slvAddr;
    rIICSTAT=0xf0; //MasTx,Start  
    //Clearing the pending bit isn't needed because the pending bit has been cleared.
    while(_iicDataCount!=-1)
     Run_LicPoll();

    _iicMode=RDDATA;

    _iicPt=0;
    _iicDataCount=1;
    
    rIICDS=slvAddr;
    rIICSTAT=0xb0; //MasRx,Start
    rIICCON=0xaf;  //resumes IIC operation.   
    while(_iicDataCount!=-1)
       Run_LicPoll();
    *data=_iicData[1];
}