com_scsi.h

6440linuxDriver的源代码

#ifndef __MV_COM_SCSI_H__
#define __MV_COM_SCSI_H__

/*
 * SCSI command
 */
#define SCSI_CMD_INQUIRY                        0x12
#define SCSI_CMD_START_STOP_UNIT                0x1B
#define SCSI_CMD_TEST_UNIT_READY                0x00
#define SCSI_CMD_RESERVE_6                      0x16
#define SCSI_CMD_RELEASE_6                      0x17

#define SCSI_CMD_READ_6                         0x08
#define SCSI_CMD_READ_10                        0x28
#define SCSI_CMD_READ_12                        0xA8
#define SCSI_CMD_READ_16                        0x88
#define SCSI_CMD_READ_LONG_10                   0x3E

#define SCSI_CMD_WRITE_6                        0x0A
#define SCSI_CMD_WRITE_10                       0x2A
#define SCSI_CMD_WRITE_12                       0xAA
#define SCSI_CMD_WRITE_16                       0x8A
#define SCSI_CMD_WRITE_LONG_10                  0x3F

#define SCSI_CMD_READ_CAPACITY_10               0x25
#define SCSI_CMD_READ_CAPACITY_16               0x9E    /* 9Eh/10h */

#define SCSI_CMD_VERIFY_10                      0x2F
#define SCSI_CMD_VERIFY_12                      0xAF
#define SCSI_CMD_VERIFY_16                      0x8F

#define SCSI_CMD_REQUEST_SENSE                  0x03
#define SCSI_CMD_MODE_SENSE_6                   0x1A
#define SCSI_CMD_MODE_SENSE_10                  0x5A
#define SCSI_CMD_MODE_SELECT_6                  0x15
#define SCSI_CMD_MODE_SELECT_10                 0x55

#define SCSI_CMD_LOG_SELECT                     0x4C
#define SCSI_CMD_LOG_SENSE                      0x4D

#define SCSI_CMD_WRITE_VERIFY_10                0x2E
#define SCSI_CMD_WRITE_VERIFY_12                0xAE
#define SCSI_CMD_WRITE_VERIFY_16                0x8E
#define SCSI_CMD_SYNCHRONIZE_CACHE_10           0x35
#define SCSI_CMD_SYNCHRONIZE_CACHE_16			0x91

#define SCSI_CMD_WRITE_SAME_10                  0x41
#define SCSI_CMD_WRITE_SAME_16                  0x93

#define SCSI_CMD_XDWRITE_10                     0x50
#define SCSI_CMD_XPWRITE_10                     0x51
#define SCSI_CMD_XDREAD_10                      0x52
#define SCSI_CMD_XDWRITEREAD_10                 0x53

#define SCSI_CMD_FORMAT_UNIT                    0x04

#define SCSI_CMD_RCV_DIAG_RSLT                  0x1C
#define SCSI_CMD_SND_DIAG                       0x1D

/* MMC */
#define SCSI_CMD_REPORT_LUN                     0xA0
#define SCSI_CMD_PREVENT_MEDIUM_REMOVAL         0x1E
#define SCSI_CMD_READ_SUB_CHANNEL               0x42
#define SCSI_CMD_READ_TOC                       0x43
#define SCSI_CMD_READ_DISC_STRUCTURE            0xAD
#define SCSI_CMD_READ_CD                        0xBE
#define SCSI_CMD_GET_EVENT_STATUS_NOTIFICATION  0x4A
#define SCSI_CMD_BLANK                          0xA1
#define SCSI_CMD_READ_DISC_INFO                 0x51

#ifndef SMART_CMD
#define SMART_CMD                               0xb0
#endif /* SMART_CMD */

#define SCSI_IS_READ(cmd)                       \
           (((cmd) == SCSI_CMD_READ_6) ||       \
	    ((cmd) == SCSI_CMD_READ_10)  ||     \
            ((cmd) == SCSI_CMD_READ_12)  ||     \
	    ((cmd) == SCSI_CMD_READ_16))

#define SCSI_IS_WRITE(cmd)                      \
           (((cmd) == SCSI_CMD_WRITE_6)  ||     \
	    ((cmd) == SCSI_CMD_WRITE_10) ||     \
	    ((cmd) == SCSI_CMD_WRITE_12) ||     \
	    ((cmd) == SCSI_CMD_WRITE_16))

#define SCSI_IS_MODE_SENSE(cmd)                 \
           (((cmd) == SCSI_CMD_MODE_SENSE_6) || \
	    ((cmd) == SCSI_CMD_MODE_SENSE_10))

#define SCSI_IS_REQUEST_SENSE(cmd)              \
           (((cmd) == SCSI_CMD_REQUEST_SENSE))

#define SCSI_IS_VERIFY(cmd)                     \
           (((cmd) == SCSI_CMD_VERIFY_10) ||    \
	    ((cmd) == SCSI_CMD_VERIFY_16))

#define SCSI_CMD_MARVELL_SPECIFIC               0xE1
#   define CDB_CORE_MODULE                      0x1
#      define CDB_CORE_SOFT_RESET_1		0x1
#      define CDB_CORE_SOFT_RESET_0		0x2
#      define CDB_CORE_IDENTIFY                 0x3
#      define CDB_CORE_SET_UDMA_MODE            0x4
#      define CDB_CORE_SET_PIO_MODE             0x5
#      define CDB_CORE_ENABLE_WRITE_CACHE       0x6
#      define CDB_CORE_DISABLE_WRITE_CACHE      0x7
#      define CDB_CORE_ENABLE_SMART             0x8
#      define CDB_CORE_DISABLE_SMART            0x9
#      define CDB_CORE_SMART_RETURN_STATUS      0xA
#      define CDB_CORE_SHUTDOWN                 0xB
#      define CDB_CORE_ENABLE_READ_AHEAD        0xC
#      define CDB_CORE_DISABLE_READ_AHEAD       0xD
#      define CDB_CORE_READ_LOG_EXT             0xE
#      define CDB_CORE_TASK_MGMT                0xF
#      define CDB_CORE_SMP                      0x10
#      define CDB_CORE_PM_READ_REG              0x11
#      define CDB_CORE_PM_WRITE_REG             0x12
#	   define CDB_CORE_RESET_DEVICE         0x13
#	   define CDB_CORE_RESET_PORT           0x14
#      define CDB_CORE_OS_SMART_CMD             0x15

#      define SMP_CDB_USE_ADDRESS               0x01

#define SCSI_IS_INTERNAL(cmd)        ((cmd) == SCSI_CMD_MARVELL_SPECIFIC)

/*
 * SCSI status
 */
#define SCSI_STATUS_GOOD                        0x00
#define SCSI_STATUS_CHECK_CONDITION             0x02
#define SCSI_STATUS_CONDITION_MET               0x04
#define SCSI_STATUS_BUSY                        0x08
#define SCSI_STATUS_INTERMEDIATE                0x10
#define SCSI_STATUS_INTERMEDIATE_MET            0x14
#define SCSI_STATUS_RESERVATION_CONFLICT        0x18
#define SCSI_STATUS_FULL                        0x28
#define SCSI_STATUS_ACA_ACTIVE                  0x30
#define SCSI_STATUS_ABORTED                     0x40

/*
 * SCSI sense key
 */
#define SCSI_SK_NO_SENSE                        0x00
#define SCSI_SK_RECOVERED_ERROR                 0x01
#define SCSI_SK_NOT_READY                       0x02
#define SCSI_SK_MEDIUM_ERROR                    0x03
#define SCSI_SK_HARDWARE_ERROR                  0x04
#define SCSI_SK_ILLEGAL_REQUEST                 0x05
#define SCSI_SK_UNIT_ATTENTION                  0x06
#define SCSI_SK_DATA_PROTECT                    0x07 
#define SCSI_SK_BLANK_CHECK                     0x08
#define SCSI_SK_VENDOR_SPECIFIC                 0x09
#define SCSI_SK_COPY_ABORTED                    0x0A
#define SCSI_SK_ABORTED_COMMAND                 0x0B
#define SCSI_SK_VOLUME_OVERFLOW                 0x0D
#define SCSI_SK_MISCOMPARE                      0x0E

/*
 * SCSI additional sense code
 */
#define SCSI_ASC_NO_ASC                         0x00
#define SCSI_ASC_LUN_NOT_READY                  0x04
#define SCSI_ASC_ECC_ERROR                      0x10
#define SCSI_ASC_ID_ADDR_MARK_NOT_FOUND         0x12
#define SCSI_ASC_INVALID_OPCODE                 0x20
#define SCSI_ASC_LBA_OUT_OF_RANGE               0x21
#define SCSI_ASC_INVALID_FEILD_IN_CDB           0x24
#define SCSI_ASC_LOGICAL_UNIT_NOT_SUPPORTED     0x25
#define SCSI_ASC_LOGICAL_UNIT_NOT_RESP_TO_SEL	0x05
#define SCSI_ASC_INVALID_FIELD_IN_PARAMETER     0x26
#define SCSI_ASC_INTERNAL_TARGET_FAILURE        0x44
#define SCSI_ASC_FAILURE_PREDICTION_THRESHOLD_EXCEEDED	0x5D

#ifdef _OS_LINUX	/* below is defined in Windows DDK scsi.h */
#define SCSI_ADSENSE_NO_SENSE  0x98    //TBD: Definition: Don't use windows
#define SCSI_ADSENSE_INVALID_CDB 0x99  //TBD: Definition: Don't use windows
#endif /* _OS_LINUX */

/*
 * SCSI additional sense code qualifier
 */
#define SCSI_ASCQ_NO_ASCQ                       0x00
#define SCSI_ASCQ_INTERVENTION_REQUIRED         0x03
#define SCSI_ASCQ_MAINTENANCE_IN_PROGRESS       0x80
#define SCSI_ASCQ_HIF_GENERAL_HD_FAILURE		0x10

/* SCSI command CDB helper functions. */
#define SCSI_CDB10_GET_LBA(cdb)                  \
           ((MV_U32) (((MV_U32) cdb[2] << 24) |  \
		      ((MV_U32) cdb[3] << 16) |  \
		      ((MV_U32) cdb[4] << 8)  |  \
		      (MV_U32) cdb[5]))

#define SCSI_CDB10_SET_LBA(cdb, lba)             \
           {                                     \
              cdb[2] = (MV_U8)(lba >> 24);       \
              cdb[3] = (MV_U8)(lba >> 16);       \
              cdb[4] = (MV_U8)(lba >> 8);        \
              cdb[5] = (MV_U8)lba;               \
           }
#define SCSI_CDB10_GET_SECTOR(cdb)    ((cdb[7] << 8) | cdb[8])

#define SCSI_CDB10_SET_SECTOR(cdb, sector)      \
           {                                    \
              cdb[7] = (MV_U8)(sector >> 8);    \
              cdb[8] = (MV_U8)sector;           \
           }

#define MV_SCSI_RESPONSE_CODE                   0x70
#define MV_SCSI_DIRECT_ACCESS_DEVICE            0x00

typedef struct _MV_Sense_Data
{
	MV_U8 ErrorCode:7;
	MV_U8 Valid:1;
	MV_U8 SegmentNumber;
	MV_U8 SenseKey:4;
	MV_U8 Reserved:1;
	MV_U8 IncorrectLength:1;
	MV_U8 EndOfMedia:1;
	MV_U8 FileMark:1;
	MV_U8 Information[4];
	MV_U8 AdditionalSenseLength;
	MV_U8 CommandSpecificInformation[4];
	MV_U8 AdditionalSenseCode;
	MV_U8 AdditionalSenseCodeQualifier;
	MV_U8 FieldReplaceableUnitCode;
	MV_U8 SenseKeySpecific[3];
}MV_Sense_Data, *PMV_Sense_Data;

MV_VOID MV_SetSenseData(
	IN PMV_Sense_Data pSense,
	IN MV_U8 SenseKey,
	IN MV_U8 AdditionalSenseCode,
	IN MV_U8 ASCQ
	);

#endif /*  __MV_COM_SCSI_H__ */