sa1100.h

strongarm的bootloader

/****************************************************************************/
/* Copyright 2000 Compaq Computer Corporation.                              */
/*                                           .                              */
/* Copying or modifying this code for any purpose is permitted,             */
/* provided that this copyright notice is preserved in its entirety         */
/* in all copies or modifications.  COMPAQ COMPUTER CORPORATION             */
/* MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, AS TO THE USEFULNESS          */
/* OR CORRECTNESS OF THIS CODE OR ITS FITNESS FOR ANY PARTICULAR            */
/* PURPOSE.                                                                 */
/****************************************************************************/

#define USR26_MODE	0x00
#define FIQ26_MODE	0x01
#define IRQ26_MODE	0x02
#define SVC26_MODE	0x03
#define USR_MODE	0x10
#define FIQ_MODE	0x11
#define IRQ_MODE	0x12
#define SVC_MODE	0x13
#define ABT_MODE	0x17
#define UND_MODE	0x1b
#define SYSTEM_MODE	0x1f
#define MODE_MASK	0x1f
#define F_BIT		0x40
#define I_BIT		0x80
#define CC_V_BIT	(1 << 28)
#define CC_C_BIT	(1 << 29)
#define CC_Z_BIT	(1 << 30)
#define CC_N_BIT	(1 << 31)

#define SA1100_UTCR0     0x00
#define SA1100_UTCR1     0x04
#define SA1100_UTCR2     0x08
#define SA1100_UTCR3     0x0C
#define SA1100_UTDR      0x14
#define SA1100_UTSR0     0x1c
#define SA1100_UTSR1     0x20

#define SA1100_UTCR0_PE		(1 << 0)   /* parity enable */
#define SA1100_UTCR0_OES	(1 << 1)   /* 1 for even parity */
#define SA1100_UTCR0_2STOP	(1 << 2)   /* 1 for 2 stop bits */
#define SA1100_UTCR0_8BIT	(1 << 3)   /* 1 for 8 bit data */
#define SA1100_UTCR0_SCE	(1 << 4)   /* sample clock enable */
#define SA1100_UTCR0_RCE	(1 << 5)   /* receive clock edge select */
#define SA1100_UTCR0_TCE	(1 << 6)   /* transmit clock edge select */

#define SA1100_UTCR1_BRDHIMASK  0xF
#define SA1100_UTCR2_BRDLoMASK  0xFF

#define SA1100_UTCR3_RXE	(1 << 0)	/* receiver enable */
#define SA1100_UTCR3_TXE	(1 << 1)	/* transmit enable */
#define SA1100_UTCR3_BRK	(1 << 2)	/* send a BRK */
#define SA1100_UTCR3_RIE	(1 << 3)	/* receive FIFO interrupt enable */
#define SA1100_UTCR3_TIE	(1 << 4)	/* transmit FIFO interrupt enable */
#define SA1100_UTCR3_LBM	(1 << 5)	/* loopback mode */

/* [1] 11.11.6 */
#define SA1100_UTDR_PRE		(1 << 8)	/* parity error */
#define SA1100_UTDR_FRE		(1 << 9)	/* framing error */
#define SA1100_UTDR_ROR		(1 << 10)	/* receiver overrun */

/* [1] 11.11.7 */
#define SA1100_UTSR0_TFS	(1 << 0)	/* transmit FIFO service request */

/* [1] 11.11.8 */
#define SA1100_UTSR1_TBY	(1 << 0)	/* transmit FIFO busy */
#define SA1100_UTSR1_RNE	(1 << 1)        /* receive FIFO not empty */
#define SA1100_UTSR1_TNF	(1 << 2)        /* transmit FIFO not full */
#define SA1100_UTSR1_PRE	(1 << 3)        /* parity error */          
#define SA1100_UTSR1_FRE	(1 << 4)        /* framing error */         
#define SA1100_UTSR1_ROR	(1 << 5)        /* receiver overrun */      

#define SA1100_UTSR1_ERROR_MASK 0x38

#define SA1100_SDLCBASE		0x80020060
#define SA1100_UART1BASE	0x80010000 
#define SA1100_UART3BASE	0x80050000 

#define SA1100_UART3_UTCR0      (SA1100_UART3BASE + SA1100_UTCR0)
#define SA1100_UART3_UTCR1      (SA1100_UART3BASE + SA1100_UTCR1)
#define SA1100_UART3_UTCR2      (SA1100_UART3BASE + SA1100_UTCR2)
#define SA1100_UART3_UTCR3      (SA1100_UART3BASE + SA1100_UTCR3)
#define SA1100_UART3_UTDR       (SA1100_UART3BASE + SA1100_UTDR)
#define SA1100_UART3_UTSR0      (SA1100_UART3BASE + SA1100_UTSR0)
#define SA1100_UART3_UTSR1      (SA1100_UART3BASE + SA1100_UTSR1)



/* 
 * DRAM Configuration values 
 */

/* [1] 10.2 */
#define SA1100_DRAM_CONFIGURATION_BASE 0xA0000000

#define SA1100_MDCNFG			0x00
#define SA1100_MDCAS00			0x04
#define SA1100_MDCAS01			0x08
#define SA1100_MDCAS02			0x0c

#define SA1100_MDREFR			0x1c

#define MDCNFG_BANK0_ENABLE (1 << 0)
#define MDCNFG_BANK1_ENABLE (1 << 1)
#define MDCNFG_DTIM0_SDRAM  (1 << 2)
#define MDCNFG_DWID0_32B    (0 << 3)
#define MDCNFG_DWID0_16B    (1 << 3)
#define MDCNFG_DRAC0(n_)    (((n_) & 7) << 4)
#define MDCNFG_TRP0(n_)     (((n_) & 0xF) << 8)
#define MDCNFG_TDL0(n_)     (((n_) & 3) << 12)
#define MDCNFG_TWR0(n_)     (((n_) & 3) << 14)
	
/* DRAM Refresh Control Register (MDREFR) [1] 10.2.2 */	
#define MDREFR_TRASR(n_)    (((n_) & 0xF) << 0)	
#define MDREFR_DRI(n_)    (((n_) & 0xFFF) << 4)
#define MDREFR_E0PIN		(1 << 16)
#define MDREFR_K0RUN		(1 << 17)
#define MDREFR_K0DB2		(1 << 18)
#define MDREFR_E1PIN		(1 << 20)	/* SDRAM clock enable pin 1 (banks 0-1) */
#define MDREFR_K1RUN		(1 << 21)	/* SDRAM clock pin 1 run (banks 0-1) */
#define MDREFR_K1DB2		(1 << 22)	/* SDRAM clock pin 1 divide-by-two (banks 0-1) */
#define MDREFR_K2RUN		(1 << 25)       /* SDRAM clock enable pin 2 (banks 2-3) */       
#define MDREFR_K2DB2		(1 << 26)       /* SDRAM clock pin 2 run (banks 2-3) */          
#define MDREFR_EAPD		(1 << 28)       /* SDRAM clock pin 2 divide-by-two (banks 2-3) */
#define MDREFR_KAPD		(1 << 29)
#define MDREFR_SLFRSH		(1 << 31)	/* SDRAM self refresh */


#define SA1100_ICMR_REG         0x90050004

#define SA1100_PPCR_REG         0x90020014

#define SA1100_PPCR_59MHZ	0
#define SA1100_PPCR_73MHZ	1
#define SA1100_PPCR_88MHZ	2
#define SA1100_PPCR_103MHZ	3
#define SA1100_PPCR_118MHZ	4
#define SA1100_PPCR_132MHZ	5
#define SA1100_PPCR_147MHZ	6
#define SA1100_PPCR_162MHZ	7
#define SA1100_PPCR_176MHZ	8
#define SA1100_PPCR_191MHZ	9
#define SA1100_PPCR_206MHZ	10
#define SA1100_PPCR_221MHZ	11



#ifdef CONFIG_BITSY
/* The EGPIO is a write only control register at physical address 0x49000000
 * See the hardware spec for more details.
 */

#define BITSY_EGPIO 0x49000000

#define EGPIO_BITSY_VPEN        (1 << 0)    /* enables erasing and programming flash.  active high. */
#define EGPIO_BITSY_CARD_RESET  (1 << 1)    /* reset the attached pcmcia/compactflash card.  active high. */
#define EGPIO_BITSY_OPT_RESET   (1 << 2)    /* reset the attached option pack.  active high. */
#define EGPIO_BITSY_CODEC_nRESET (1 << 3)   /* reset the onboard UDA1341.  active low. */
#define EGPIO_BITSY_OPT_NVRAM_ON (1 << 4)   /* apply power to optionpack nvram, active high. */
#define EGPIO_BITSY_OPT_ON       (1 << 5)   /* full power to option pack.  active high. */
#define EGPIO_BITSY_LCD_ON       (1 << 6)   /* enable 3.3V to LCD.  active high. */
#define EGPIO_BITSY_RS232_ON     (1 << 7)   /* UART3 transceiver force on.  Active high. */
#define EGPIO_BITSY_LCD_PCI      (1 << 8)   /* LCD control IC enable.  active high. */
#define EGPIO_BITSY_IR_ON        (1 << 9)   /* apply power to IR module.  active high. */
#define EGPIO_BITSY_AUD_AMP_ON   (1 << 10)  /* apply power to audio power amp.  active high. */
#define EGPIO_BITSY_AUD_PWR_ON   (1 << 11)  /* apply poewr to reset of audio circuit.  active high. */
#define EGPIO_BITSY_QMUTE        (1 << 12)  /* mute control for onboard UDA1341.  active high. */
#define EGPIO_BITSY_IR_FSEL      (1 << 13)  /* IR speed select: 1->fast, 0->slow */
#define EGPIO_BITSY_LCD_5V_ON    (1 << 14)  /* enable 5V to LCD. active high. */
#define EGPIO_BITSY_LVDD_ON      (1 << 15)  /* enable 9V and -6.5V to LCD. */

#endif