start.s.svn-base

u-boot for S3c2443 processor

	mtspr   DBAT5U, r3
	isync

	/* IBAT 6 */
	addis   r4, r0, CFG_IBAT6L@h
	ori     r4, r4, CFG_IBAT6L@l
	addis   r3, r0, CFG_IBAT6U@h
	ori     r3, r3, CFG_IBAT6U@l
	mtspr   IBAT6L, r4
	mtspr   IBAT6U, r3
	isync

	/* DBAT 6 */
	addis   r4, r0, CFG_DBAT6L@h
	ori     r4, r4, CFG_DBAT6L@l
	addis   r3, r0, CFG_DBAT6U@h
	ori     r3, r3, CFG_DBAT6U@l
	mtspr   DBAT6L, r4
	mtspr   DBAT6U, r3
	isync

	/* IBAT 7 */
	addis   r4, r0, CFG_IBAT7L@h
	ori     r4, r4, CFG_IBAT7L@l
	addis   r3, r0, CFG_IBAT7U@h
	ori     r3, r3, CFG_IBAT7U@l
	mtspr   IBAT7L, r4
	mtspr   IBAT7U, r3
	isync

	/* DBAT 7 */
	addis   r4, r0, CFG_DBAT7L@h
	ori     r4, r4, CFG_DBAT7L@l
	addis   r3, r0, CFG_DBAT7U@h
	ori     r3, r3, CFG_DBAT7U@l
	mtspr   DBAT7L, r4
	mtspr   DBAT7U, r3
	isync
#endif

	/* bats are done, now invalidate the TLBs */

	addis	r3, 0, 0x0000
	addis	r5, 0, 0x4    /* upper bound of 0x00040000 for 7400/750 */

	isync

tlblp:
	tlbie	r3
	sync
	addi	r3, r3, 0x1000
	cmp	0, 0, r3, r5
	blt tlblp

	blr

	.globl enable_addr_trans
enable_addr_trans:
	/* enable address translation */
	mfmsr	r5
	ori	r5, r5, (MSR_IR | MSR_DR)
	mtmsr	r5
	isync
	blr

	.globl disable_addr_trans
disable_addr_trans:
	/* disable address translation */
	mflr	r4
	mfmsr	r3
	andi.	r0, r3, (MSR_IR | MSR_DR)
	beqlr
	andc	r3, r3, r0
	mtspr	SRR0, r4
	mtspr	SRR1, r3
	rfi

/*
 * This code finishes saving the registers to the exception frame
 * and jumps to the appropriate handler for the exception.
 * Register r21 is pointer into trap frame, r1 has new stack pointer.
 */
	.globl	transfer_to_handler
transfer_to_handler:
	stw	r22,_NIP(r21)
	lis	r22,MSR_POW@h
	andc	r23,r23,r22
	stw	r23,_MSR(r21)
	SAVE_GPR(7, r21)
	SAVE_4GPRS(8, r21)
	SAVE_8GPRS(12, r21)
	SAVE_8GPRS(24, r21)
	mflr	r23
	andi.	r24,r23,0x3f00		/* get vector offset */
	stw	r24,TRAP(r21)
	li	r22,0
	stw	r22,RESULT(r21)
	mtspr	SPRG2,r22		/* r1 is now kernel sp */
	lwz	r24,0(r23)		/* virtual address of handler */
	lwz	r23,4(r23)		/* where to go when done */
	mtspr	SRR0,r24
	mtspr	SRR1,r20
	mtlr	r23
	SYNC
	rfi				/* jump to handler, enable MMU */

int_return:
	mfmsr	r28		/* Disable interrupts */
	li	r4,0
	ori	r4,r4,MSR_EE
	andc	r28,r28,r4
	SYNC			/* Some chip revs need this... */
	mtmsr	r28
	SYNC
	lwz	r2,_CTR(r1)
	lwz	r0,_LINK(r1)
	mtctr	r2
	mtlr	r0
	lwz	r2,_XER(r1)
	lwz	r0,_CCR(r1)
	mtspr	XER,r2
	mtcrf	0xFF,r0
	REST_10GPRS(3, r1)
	REST_10GPRS(13, r1)
	REST_8GPRS(23, r1)
	REST_GPR(31, r1)
	lwz	r2,_NIP(r1)	/* Restore environment */
	lwz	r0,_MSR(r1)
	mtspr	SRR0,r2
	mtspr	SRR1,r0
	lwz	r0,GPR0(r1)
	lwz	r2,GPR2(r1)
	lwz	r1,GPR1(r1)
	SYNC
	rfi

	.globl	dc_read
dc_read:
	blr

	.globl get_pvr
get_pvr:
	mfspr	r3, PVR
	blr

/*-----------------------------------------------------------------------*/
/*
 * void relocate_code (addr_sp, gd, addr_moni)
 *
 * This "function" does not return, instead it continues in RAM
 * after relocating the monitor code.
 *
 * r3 = dest
 * r4 = src
 * r5 = length in bytes
 * r6 = cachelinesize
 */
	.globl	relocate_code
relocate_code:
	mr	r1,  r3		/* Set new stack pointer		*/
	mr	r9,  r4		/* Save copy of Global Data pointer	*/
	mr	r10, r5		/* Save copy of Destination Address	*/

	mr	r3,  r5				/* Destination Address	*/
	lis	r4, CFG_MONITOR_BASE@h		/* Source      Address	*/
	ori	r4, r4, CFG_MONITOR_BASE@l
	lwz	r5, GOT(__init_end)
	sub	r5, r5, r4
	li	r6, CFG_CACHELINE_SIZE		/* Cache Line Size	*/

	/*
	 * Fix GOT pointer:
	 *
	 * New GOT-PTR = (old GOT-PTR - CFG_MONITOR_BASE) + Destination Address
	 *
	 * Offset:
	 */
	sub	r15, r10, r4

	/* First our own GOT */
	add	r14, r14, r15
	/* then the one used by the C code */
	add	r30, r30, r15

	/*
	 * Now relocate code
	 */
#ifdef CONFIG_ECC
	bl	board_relocate_rom
	sync
	mr	r3, r10				/* Destination Address	*/
	lis	r4, CFG_MONITOR_BASE@h		/* Source      Address	*/
	ori	r4, r4, CFG_MONITOR_BASE@l
	lwz	r5, GOT(__init_end)
	sub	r5, r5, r4
	li	r6, CFG_CACHELINE_SIZE		/* Cache Line Size	*/
#else
	cmplw	cr1,r3,r4
	addi	r0,r5,3
	srwi.	r0,r0,2
	beq	cr1,4f		/* In place copy is not necessary	*/
	beq	7f		/* Protect against 0 count		*/
	mtctr	r0
	bge	cr1,2f

	la	r8,-4(r4)
	la	r7,-4(r3)
1:	lwzu	r0,4(r8)
	stwu	r0,4(r7)
	bdnz	1b
	b	4f

2:	slwi	r0,r0,2
	add	r8,r4,r0
	add	r7,r3,r0
3:	lwzu	r0,-4(r8)
	stwu	r0,-4(r7)
	bdnz	3b
#endif
/*
 * Now flush the cache: note that we must start from a cache aligned
 * address. Otherwise we might miss one cache line.
 */
4:	cmpwi	r6,0
	add	r5,r3,r5
	beq	7f		/* Always flush prefetch queue in any case */
	subi	r0,r6,1
	andc	r3,r3,r0
	mr	r4,r3
5:	dcbst	0,r4
	add	r4,r4,r6
	cmplw	r4,r5
	blt	5b
	sync			/* Wait for all dcbst to complete on bus */
	mr	r4,r3
6:	icbi	0,r4
	add	r4,r4,r6
	cmplw	r4,r5
	blt	6b
7:	sync			/* Wait for all icbi to complete on bus	*/
	isync

/*
 * We are done. Do not return, instead branch to second part of board
 * initialization, now running from RAM.
 */
	addi	r0, r10, in_ram - _start + EXC_OFF_SYS_RESET
	mtlr	r0
	blr

in_ram:
#ifdef CONFIG_ECC
	bl	board_init_ecc
#endif
	/*
	 * Relocation Function, r14 point to got2+0x8000
	 *
	 * Adjust got2 pointers, no need to check for 0, this code
	 * already puts a few entries in the table.
	 */
	li	r0,__got2_entries@sectoff@l
	la	r3,GOT(_GOT2_TABLE_)
	lwz	r11,GOT(_GOT2_TABLE_)
	mtctr	r0
	sub	r11,r3,r11
	addi	r3,r3,-4
1:	lwzu	r0,4(r3)
	add	r0,r0,r11
	stw	r0,0(r3)
	bdnz	1b

	/*
	 * Now adjust the fixups and the pointers to the fixups
	 * in case we need to move ourselves again.
	 */
2:	li	r0,__fixup_entries@sectoff@l
	lwz	r3,GOT(_FIXUP_TABLE_)
	cmpwi	r0,0
	mtctr	r0
	addi	r3,r3,-4
	beq	4f
3:	lwzu	r4,4(r3)
	lwzux	r0,r4,r11
	add	r0,r0,r11
	stw	r10,0(r3)
	stw	r0,0(r4)
	bdnz	3b
4:
/* clear_bss: */
	/*
	 * Now clear BSS segment
	 */
	lwz	r3,GOT(__bss_start)
	lwz	r4,GOT(_end)

	cmplw	0, r3, r4
	beq	6f

	li	r0, 0
5:
	stw	r0, 0(r3)
	addi	r3, r3, 4
	cmplw	0, r3, r4
	bne	5b
6:
	mr	r3, r10		/* Destination Address		*/
#if defined(CONFIG_AMIGAONEG3SE) || \
    defined(CONFIG_DB64360)	 || \
    defined(CONFIG_DB64460)
	mr	r4, r9		/* Use RAM copy of the global data */
#endif
	bl	after_reloc

	/* not reached - end relocate_code */
/*-----------------------------------------------------------------------*/

	/*
	 * Copy exception vector code to low memory
	 *
	 * r3: dest_addr
	 * r7: source address, r8: end address, r9: target address
	 */
	.globl	trap_init
trap_init:
	lwz	r7, GOT(_start)
	lwz	r8, GOT(_end_of_vectors)

	li	r9, 0x100		/* reset vector always at 0x100 */

	cmplw	0, r7, r8
	bgelr				/* return if r7>=r8 - just in case */

	mflr	r4			/* save link register		*/
1:
	lwz	r0, 0(r7)
	stw	r0, 0(r9)
	addi	r7, r7, 4
	addi	r9, r9, 4
	cmplw	0, r7, r8
	bne	1b

	/*
	 * relocate `hdlr' and `int_return' entries
	 */
	li	r7, .L_MachineCheck - _start + EXC_OFF_SYS_RESET
	li	r8, Alignment - _start + EXC_OFF_SYS_RESET
2:
	bl	trap_reloc
	addi	r7, r7, 0x100		/* next exception vector	*/
	cmplw	0, r7, r8
	blt	2b

	li	r7, .L_Alignment - _start + EXC_OFF_SYS_RESET
	bl	trap_reloc

	li	r7, .L_ProgramCheck - _start + EXC_OFF_SYS_RESET
	bl	trap_reloc

	li	r7, .L_FPUnavailable - _start + EXC_OFF_SYS_RESET
	li	r8, SystemCall - _start + EXC_OFF_SYS_RESET
3:
	bl	trap_reloc
	addi	r7, r7, 0x100		/* next exception vector	*/
	cmplw	0, r7, r8
	blt	3b

	li	r7, .L_SingleStep - _start + EXC_OFF_SYS_RESET
	li	r8, _end_of_vectors - _start + EXC_OFF_SYS_RESET
4:
	bl	trap_reloc
	addi	r7, r7, 0x100		/* next exception vector	*/
	cmplw	0, r7, r8
	blt	4b

	/* enable execptions from RAM vectors */
	mfmsr	r7
	li	r8,MSR_IP
	andc	r7,r7,r8
	mtmsr	r7

	mtlr	r4			/* restore link register	*/
	blr

	/*
	 * Function: relocate entries for one exception vector
	 */
trap_reloc:
	lwz	r0, 0(r7)		/* hdlr ...			*/
	add	r0, r0, r3		/*  ... += dest_addr		*/
	stw	r0, 0(r7)

	lwz	r0, 4(r7)		/* int_return ...		*/
	add	r0, r0, r3		/*  ... += dest_addr		*/
	stw	r0, 4(r7)

	sync
	isync

	blr

#ifdef CFG_INIT_RAM_LOCK
lock_ram_in_cache:
	/* Allocate Initial RAM in data cache.
	 */
	lis	r3, (CFG_INIT_RAM_ADDR & ~31)@h
	ori	r3, r3, (CFG_INIT_RAM_ADDR & ~31)@l
	li	r2, ((CFG_INIT_RAM_END & ~31) + \
		     (CFG_INIT_RAM_ADDR & 31) + 31) / 32
	mtctr	r2
1:
	dcbz	r0, r3
	addi	r3, r3, 32
	bdnz	1b

	/* Lock the data cache */
	mfspr	r0, HID0
	ori	r0, r0, 0x1000
	sync
	mtspr	HID0, r0
	sync
	blr

.globl unlock_ram_in_cache
unlock_ram_in_cache:
	/* invalidate the INIT_RAM section */
	lis	r3, (CFG_INIT_RAM_ADDR & ~31)@h
	ori	r3, r3, (CFG_INIT_RAM_ADDR & ~31)@l
	li	r2, ((CFG_INIT_RAM_END & ~31) + \
		     (CFG_INIT_RAM_ADDR & 31) + 31) / 32
	mtctr	r2
1:	icbi	r0, r3
	addi	r3, r3, 32
	bdnz	1b
	sync			/* Wait for all icbi to complete on bus	*/
	isync

	/* Unlock the data cache and invalidate it */
	mfspr   r0, HID0
	li      r3,0x1000
	andc    r0,r0,r3
	li	r3,0x0400
	or	r0,r0,r3
	sync
	mtspr   HID0, r0
	sync
	blr
#endif