pq2fads.cfg

BDI2000 FOR PPC860 固件程序

; bdiWind configuration file for PQ2FADS-ZU board
; -----------------------------------------------
;
[INIT]
; init core register
WREG    MSR             0x00001002      ;MSR  : ME,RI
WM32	0x0F010004	0xFFFFFFC3	;SYPCR: disable watchdog
WM32	0x0F0101A8	0x04700000	;IMMR : internal space @ 0x04700000
WM32	0x04710024	0x100C0000	;BCR  : Single PQ2, ..
WM32	0x04710c94	0x00000001	;RMR  : checkstop reset enable
;
; init memory controller
WM32	0x04710104	0xFF800876	;OR0: Flash 8MB, CS early negate, 11 w.s., Timing relax
WM32	0x04710100	0xFF801801	;BR0: Flash @0xFF800000, 32bit, no parity
WM32	0x0471010C	0xFFFF8010	;OR1: BCSR 32KB, all types access, 1 w.s.
WM32	0x04710108	0x04501801	;BR1: BCSR @0x04500000, 32bit, no parity
WM32	0x04710124	0xFFFF8866	;OR4: EEPROM 32KB, all types access, 6 w.s.
WM32	0x04710120	0xC2000801	;BR4: EEPROM @0xC2000000, 8bit, no parity

; init SDRAM Init (PPC bus)
WM16	0x04710184	0x2800	        ;MPTPR: Divide Bus clock by 41
WM8	0x0471019C	0x13	        ;PSRT : Divide MPTPR output by 20
WM32	0x04710114	0xfe002ec0	;OR2  : 32MB, 2 banks, row start at A9, 11 rows
WM32	0x04710110	0x00000041	;BR2  : SDRAM @0x00000000, 64bit, no parity
WM32	0x04710190	0x824b36a3	;PSDMR: Precharge all banks
WM32	0x04710190	0xaa4b36a3
WM8	0x00000000	0x00	        ;Access SDRAM
WM32	0x04710190	0x8a4b36a3	;PSDMR: CBR Refresh
WM8	0x00000000	0xFF	        ;Access SDRAM
WM8	0x00000000	0xFF	        ;Access SDRAM
WM8	0x00000000	0xFF	        ;Access SDRAM
WM8	0x00000000	0xFF	        ;Access SDRAM
WM8	0x00000000	0xFF	        ;Access SDRAM
WM8	0x00000000	0xFF	        ;Access SDRAM
WM8	0x00000000	0xFF	        ;Access SDRAM
WM8	0x00000000	0xFF	        ;Access SDRAM
WM32	0x04710190	0x9a4b36a3	;PSDMR: Mode Set
WM8	0x00000190	0x00	        ;Access SDRAM
WM32	0x04710190	0xc24b36a3	;PSDMR: enable refresh, normal operation

; init Local Bus SDRAM (100MHz)
WM8	0x047101a4	0x13	        ;LSRT
WM32	0x0471011c	0xff803280	;OR3
WM32	0x04710118	0xd0001861	;BR3
WM32	0x04710194	0x828737a3	;LSDMR: Precharge all banks
WM32	0x04710194	0xaa8737a3
WM8	0xd0000000	0x00	        ;Access SDRAM
WM32	0x04710194	0x8a8737a3	;LSDMR: CBR Refresh
WM8	0xd0000000	0xFF	        ;Access SDRAM
WM8	0xd0000000	0xFF	        ;Access SDRAM
WM8	0xd0000000	0xFF	        ;Access SDRAM
WM8	0xd0000000	0xFF	        ;Access SDRAM
WM32	0x04710194	0x9a8737a3	;LSDMR: Mode Set
WM8	0xd00000cc	0x00	        ;Access SDRAM
WM32	0x04710194	0xc28737a3	;LSDMR: enable refresh, normal operation


[TARGET]
CPUTYPE     8280        ;the CPU type
JTAGCLOCK   0           ;use 16 MHz JTAG clock
POWERUP     7000        ;start delay after power-up detected in ms
BOOTADDR    0xfff00100  ;boot address used for start-up break
WORKSPACE   0x04700000	;workspace in target RAM for fast download
BDIMODE     AGENT     	;the BDI working mode (LOADONLY | AGENT | GATEWAY)
BREAKMODE   SOFT      	;SOFT or HARD, HARD uses PPC hardware breakpoint
STEPMODE    TRACE       ;TRACE or HWBP, HWPB uses a hardware breakpoint
DCACHE      NOFLUSH
;MEMDELAY    2000        ;additional memory access delay

MEMBASE     0         	;<AGENT> base of target memory
MEMSIZE     0x04000000 	;<AGENT> size of target memory
POOLBASE    0x03FF0000 	;<AGENT> base of host controlled target memory
POOLSIZE    0x00010000 	;<AGENT> size of host controlled target memory

[HOST]
IP          151.120.25.119
FILE        E:\cygwin\home\bdidemo\mpc8260\vxworks
FORMAT      ELF
LOAD        MANUAL      ;load code MANUAL or AUTO after reset
DEBUGPORT   0x4321
PROMPT      8280>	;new prompt for Telnet

[FLASH]
CHIPTYPE    I28BX8      ;Flash type (AM29F | AM29BX8 | AM29BX16 | I28BX8 | I28BX16)
CHIPSIZE    0x200000    ;The size of one flash chip in bytes
BUSWIDTH    32          ;The width of the flash memory bus in bits (8 | 16 | 32 | 64)
WORKSPACE   0x04700000  ;workspace in dual port RAM
FILE        E:\cygwin\home\bdidemo\mpc8260\u-boot.bin
FORMAT      BIN 0xFFF00000
ERASE       0xFFF00000  ;erase sector 28 of flash SIMM (LH28F016SCT)
ERASE       0xFFF40000  ;erase sector 29 of flash SIMM

[REGS]
DMM1        0x04700000
FILE        E:\cygwin\home\bdidemo\mpc8260\reg8280.def