utils.c

该2440 BSP是由三星公司提供的wince5.0的BSP移植到到wince6.0下的

#include <windows.h>
#include "s2440addr.h"

// Function prototypes.
//
void Delay(void);
void MMU_SetAsyncBusMode(void);


//***************************[ PORTS ]****************************************************
void Port_Init(void)
{
    //CAUTION:Follow the configuration order for setting the ports. 
    // 1) setting value(GPnDAT) 
    // 2) setting control register  (GPnCON)
    // 3) configure pull-up resistor(GPnUP)  

    //32bit data bus configuration  
    //*** PORT A GROUP
    //Ports  : GPA22 GPA21  GPA20 GPA19 GPA18 GPA17 GPA16 GPA15 GPA14 GPA13 GPA12  
    //Signal : nFCE nRSTOUT nFRE   nFWE  ALE   CLE  nGCS5 nGCS4 nGCS3 nGCS2 nGCS1 
    //Binary :  1     1      1  , 1   1   1    1   ,  1     1     1     1
    //Ports  : GPA11   GPA10  GPA9   GPA8   GPA7   GPA6   GPA5   GPA4   GPA3   GPA2   GPA1  GPA0
    //Signal : ADDR26 ADDR25 ADDR24 ADDR23 ADDR22 ADDR21 ADDR20 ADDR19 ADDR18 ADDR17 ADDR16 ADDR0 
    //Binary :  1       1      1      1   , 1       1      1      1   ,  1       1     1      1         
    rGPACON = 0x7fffff; 

    //**** PORT B GROUP
    //Ports  : GPB10    GPB9    GPB8    GPB7    GPB6     GPB5    GPB4   GPB3   GPB2     GPB1      GPB0
    //Signal : nXDREQ0 nXDACK0 nXDREQ1 nXDACK1 nSS_KBD nDIS_OFF L3CLOCK L3DATA L3MODE nIrDATXDEN Keyboard
    //Setting: INPUT  OUTPUT   INPUT  OUTPUT   INPUT   OUTPUT   OUTPUT OUTPUT OUTPUT   OUTPUT    OUTPUT 
    //Binary :   00  ,  01       00  ,   01      00   ,  01       01  ,   01     01   ,  01        01  
    rGPBCON = 0x044555;
    rGPBUP  = 0x7ff;     // The pull up function is disabled GPB[10:0]

    //*** PORT C GROUP
    //Ports  : GPC15 GPC14 GPC13 GPC12 GPC11 GPC10 GPC9 GPC8  GPC7   GPC6   GPC5 GPC4 GPC3  GPC2  GPC1 GPC0
    //Signal : VD7   VD6   VD5   VD4   VD3   VD2   VD1  VD0 LCDVF2 LCDVF1 LCDVF0 VM VFRAME VLINE VCLK LEND  
    //Binary :  10   10  , 10    10  , 10    10  , 10   10  , 10     10  ,  10   10 , 10     10 , 10   10
    rGPCCON = 0xaaaaaaaa;       
    rGPCUP  = 0xffff;     // The pull up function is disabled GPC[15:0] 

    //*** PORT D GROUP
    //Ports  : GPD15 GPD14 GPD13 GPD12 GPD11 GPD10 GPD9 GPD8 GPD7 GPD6 GPD5 GPD4 GPD3 GPD2 GPD1 GPD0
    //Signal : VD23  VD22  VD21  VD20  VD19  VD18  VD17 VD16 VD15 VD14 VD13 VD12 VD11 VD10 VD9  VD8
    //Binary : 10    10  , 10    10  , 10    10  , 10   10 , 10   10 , 10   10 , 10   10 ,10   10
    rGPDCON = 0xaaaaaaaa;       
    rGPDUP  = 0xffff;     // The pull up function is disabled GPD[15:0]

    //*** PORT E GROUP
    //Ports  : GPE15  GPE14 GPE13   GPE12   GPE11   GPE10   GPE9    GPE8     GPE7  GPE6  GPE5   GPE4  
    //Signal : IICSDA IICSCL SPICLK SPIMOSI SPIMISO SDDATA3 SDDATA2 SDDATA1 SDDATA0 SDCMD SDCLK I2SSDO 
    //Binary :  10     10  ,  10      10  ,  10      10   ,  10      10   ,   10    10  , 10     10  ,     
    //-------------------------------------------------------------------------------------------------------
    //Ports  :  GPE3   GPE2  GPE1    GPE0    
    //Signal : I2SSDI CDCLK I2SSCLK I2SLRCK     
    //Binary :  10     10  ,  10      10 
    rGPECON = 0xaaaaaaaa;       
    rGPEUP  = 0xffff;     // The pull up function is disabled GPE[15:0]

    //*** PORT F GROUP
    //Ports  : GPF7   GPF6   GPF5   GPF4      GPF3     GPF2  GPF1   GPF0
    //Signal : nLED_8 nLED_4 nLED_2 nLED_1 nIRQ_PCMCIA EINT2 KBDINT EINT0
    //Setting: Output Output Output Output    EINT3    EINT2 EINT1  EINT0
    //Binary :  01      01 ,  01     01  ,     10       10  , 10     10
    rGPFCON = 0x55aa;
    rGPFUP  = 0xff;     // The pull up function is disabled GPF[7:0]

    //*** PORT G GROUP
    //Ports  : GPG15 GPG14 GPG13 GPG12 GPG11    GPG10    GPG9     GPG8     GPG7      GPG6    
    //Signal : nYPON  YMON nXPON XMON  EINT19 DMAMODE1 DMAMODE0 DMASTART KBDSPICLK KBDSPIMOSI
    //Setting: nYPON  YMON nXPON XMON  EINT19  Output   Output   Output   SPICLK1    SPIMOSI1
    //Binary :   11    11 , 11    11  , 10      01    ,   01       01   ,    11         11
    //-----------------------------------------------------------------------------------------
    //Ports  :    GPG5       GPG4    GPG3    GPG2    GPG1    GPG0    
    //Signal : KBDSPIMISO LCD_PWREN EINT11 nSS_SPI IRQ_LAN IRQ_PCMCIA
    //Setting:  SPIMISO1  LCD_PWRDN EINT11   nSS0   EINT9    EINT8
    //Binary :     11         11   ,  10      11  ,  10        10
    rGPGCON = 0xff95ffba;
    rGPGUP  = 0xffff;    // The pull up function is disabled GPG[15:0]

    //*** PORT H GROUP
    //Ports  :  GPH10    GPH9  GPH8 GPH7  GPH6  GPH5 GPH4 GPH3 GPH2 GPH1  GPH0 
    //Signal : CLKOUT1 CLKOUT0 UCLK nCTS1 nRTS1 RXD1 TXD1 RXD0 TXD0 nRTS0 nCTS0
    //Binary :   01   ,  01     10 , 11    11  , 10   10 , 10   10 , 10    10
    rGPHCON = 0x16faaa;
    rGPHUP  = 0x7ff;    // The pull up function is disabled GPH[10:0]
    
    //External interrupt will be falling edge triggered. 
    rEXTINT0 = 0x22222222;    // EINT[7:0]
    rEXTINT1 = 0x22222222;    // EINT[15:8]
    rEXTINT2 = 0x22222222;    // EINT[23:16]
}


void Led_Display(int data)
{
    // Active is low.(LED On)
    // GPF7  GPF6   GPF5   GPF4
    // nLED_8 nLED4 nLED_2 nLED_1
    //
    rGPFDAT = (rGPFDAT & ~(0xf<<4)) | ((~data & 0xf)<<4);    
}


void ChangeClockDivider(int hdivn, int pdivn)
{
    // hdivn,pdivn FCLK:HCLK:PCLK
    //     0,0         1:1:1 
    //     0,1         1:1:2 
    //     1,0         1:2:2
    //     1,1         1:2:4
    rCLKDIVN = (hdivn<<1) | pdivn;    
    
    if(hdivn)
    {
        MMU_SetAsyncBusMode();
    }
}


void ChangeMPllValue(int mdiv, int pdiv, int sdiv)
{
    rMPLLCON = (mdiv<<12) | (pdiv<<4) | sdiv;
}

// Do-nothing delay loop.
//
void Delay(void)
{
    volatile int i;

    for(i=0 ; i < 1000 ; i++)
    {
    }
}

//***************************[ UART ]******************************
void Uart_Init(void)
{
    int i;

    rUFCON1 = 0x0;      // FIFO disable
    rUMCON1 = 0x0;      // AFC disable

    rULCON1 = 0x3;      // Normal,No parity,1 stop,8 bits
    rUCON1  = 0x245;   
    
    rUBRDIV1=( (int)(PCLK/16./115200) -1 );

    for(i=0;i<100;i++);
    
}

//=====================================================================
void Uart_SendByte(int data)
{
        if(data=='\n')
        {
            while(!(rUTRSTAT1 & 0x2));
            Delay();                 //because the slow response of hyper_terminal 
            WrUTXH1('\r');
        }

        while(!(rUTRSTAT1 & 0x2));   //Wait until THR is empty.
        Delay();
        WrUTXH1(data);
}               


//====================================================================
void Uart_SendString(char *pt)
{
    while(*pt)
        Uart_SendByte(*pt++);
}

//====================================================================
void Uart_SendDWORD(DWORD d, BOOL cr)
{
    Uart_SendString("0x");
    Uart_SendString(hex2char((d & 0xf0000000) >> 28));
    Uart_SendString(hex2char((d & 0x0f000000) >> 24));
    Uart_SendString(hex2char((d & 0x00f00000) >> 20));    
    Uart_SendString(hex2char((d & 0x000f0000) >> 16));
    Uart_SendString(hex2char((d & 0x0000f000) >> 12));
    Uart_SendString(hex2char((d & 0x00000f00) >> 8));
    Uart_SendString(hex2char((d & 0x000000f0) >> 4));
    Uart_SendString(hex2char((d & 0x0000000f) >> 0));
    if (cr)
        Uart_SendString("\n");
}

//====================================================================
char *hex2char(unsigned int val)
{
    static char str[2];

    str[1]='\0';	
    
    if(val<=9)
        str[0]='0'+val;
    else 
        str[0]=('a'+val-10);
        
    return str;
}