avrdude.conf

这是一些关于avr单片机的一些有用的资料

  type  = par;
  reset = 4;
  sck   = 3;
  mosi  = 2;
  miso  = 10;
;

programmer
  id    = "futurlec";
  desc  = "Futurlec.com programming cable.";
  type  = par;
  reset = 3;
  sck   = 2;
  mosi  = 1;
  miso  = 10;
;


# From the contributor of the "xil" jtag cable:
# The "vcc" definition isn't really vcc (the cable gets its power from
# the programming circuit) but is necessary to switch one of the
# buffer lines (trying to add it to the "buff" lines doesn't work).
# With this, TMS connects to RESET, TDI to MOSI, TDO to MISO and TCK
# to SCK (plus vcc/gnd of course)
programmer
  id    = "xil";
  desc  = "Xilinx JTAG cable";
  type  = par;
  mosi  = 2;
  sck   = 3;
  reset = 4;
  buff  = 5;
  miso  = 13;
  vcc   = 6;
;


programmer
  id = "dapa";
  desc = "Direct AVR Parallel Access cable";
  type = par;
  vcc   = 3;
  reset = 16;
  sck = 1;
  mosi = 2;
  miso = 11;
;


#
# some ultra cheap programmers use bitbanging on the 
# serialport.
#

# serial ponyprog design (dasa2 in uisp)
# reset=!txd sck=rts mosi=dtr miso=cts

#programmer
#  id    = "ponyser";
#  desc  = "serial port banging, design ponyprog serial";
#  type  = serbb;
#  reset = ~3;
#  sck   = 6;
#  mosi  = 4;
#  miso  = 7;
#;

# unknown (dasa in uisp)
# reset=rts sck=dtr mosi=txd miso=cts

#programmer
#  id    = "dasa";
#  desc  = "serial port banging, reset=rts sck=dtr mosi=txd miso=cts";
#  type  = serbb;
#  reset = 6;
#  sck   = 4;
#  mosi  = 3;
#  miso  = 7;
#;

# unknown (dasa3 in uisp)
# reset=!dtr sck=rts mosi=txd miso=cts

#programmer
#  id    = "dasa3";
#  desc  = "serial port banging, reset=!dtr sck=rts mosi=txd miso=cts";
#  type  = serbb;
#  reset = ~4;
#  sck   = 6;
#  mosi  = 3;
#  miso  = 7;
#;

programmer
  id    = "usbasp";
  desc  = "usbasp";
  type  = usbasp;
;

#
# PART DEFINITIONS
#

#------------------------------------------------------------
# ATtiny12
#------------------------------------------------------------

part
    id                  = "t12";
    desc                = "ATtiny12";
    stk500_devcode      = 0x12;
    avr910_devcode      = 0x55;
    chip_erase_delay    = 20000;
    pgm_enable          = "1 0 1 0  1 1 0 0   0 1 0 1  0 0 1 1",
                          "x x x x  x x x x   x x x x  x x x x";

    chip_erase          = "1 0 1 0  1 1 0 0   1 0 0 x  x x x x",
                          "x x x x  x x x x   x x x x  x x x x";

    timeout		= 200;
    stabdelay		= 100;
    cmdexedelay		= 25;
    synchloops		= 32;
    bytedelay		= 0;
    pollindex		= 3;
    pollvalue		= 0x53;
    predelay		= 1;
    postdelay		= 1;
    pollmethod		= 0;

    memory "eeprom"
        size            = 64;
        min_write_delay = 9000;
        max_write_delay = 20000;
        readback_p1     = 0xff;
        readback_p2     = 0xff;
        read            = "1  0  1  0   0  0  0  0    x x x x  x x x x",
                          "x  x a5 a4  a3 a2 a1 a0    o o o o  o o o o";

        write           = "1  1  0  0   0  0  0  0    x x x x  x x x x",
                          "x  x a5 a4  a3 a2 a1 a0    i i i i  i i i i";

	mode		= 0x04;
	delay		= 8;
	blocksize	= 64;
	readsize	= 256;
    ;

    memory "flash"
        size            = 1024;
        min_write_delay = 4500;
        max_write_delay = 20000;
        readback_p1     = 0xff;
        readback_p2     = 0xff;
        read_lo         = "  0  0  1  0   0  0  0  0",
                          "  x  x  x  x   x  x  x a8",
                          " a7 a6 a5 a4  a3 a2 a1 a0",
                          "  o  o  o  o   o  o  o  o";

        read_hi         = "  0  0  1  0   1  0  0  0",
                          "  x  x  x  x   x  x  x a8",
                          " a7 a6 a5 a4  a3 a2 a1 a0",
                          "  o  o  o  o   o  o  o  o";

        write_lo        = "  0  1  0  0   0  0  0  0",
                          "  x  x  x  x   x  x  x a8",
                          " a7 a6 a5 a4  a3 a2 a1 a0",
                          "  i  i  i  i   i  i  i  i";

        write_hi        = "  0  1  0  0   1  0  0  0",
                          "  x  x  x  x   x  x  x a8",
                          " a7 a6 a5 a4  a3 a2 a1 a0",
                          "  i  i  i  i   i  i  i  i";

	mode		= 0x04;
	delay		= 5;
	blocksize	= 128;
	readsize	= 256;
    ;

    memory "signature"
        size            = 3;
        read            = "0  0  1  1   0  0  0  0    x x x x  x x x x",
                          "0  0  0  0   0  0 a1 a0    o o o o  o o o o";
    ;

    memory "lock"
        size            = 1;
        read            = "0  1  0  1   1  0  0  0    x x x x  x x x x",
                          "x  x  x  x   x  x  x  x    x x x x  x o o x";

        write           = "1  0  1  0   1  1  0  0    1 1 1 1  1 i i 1",
                          "x  x  x  x   x  x  x  x    x x x x  x x x x";
    ;

    memory "calibration"
        size            = 1;
        read            = "0  0  1  1   1  0  0  0    x x x x  x x x x",
                          "0  0  0  0   0  0  0  0    o o o o  o o o o";
    ;

    memory "fuse"
        size            = 1;
        read            = "0  1  0  1   0  0  0  0    x x x x  x x x x",
                          "x  x  x  x   x  x  x  x    o o o o  o o o o";

        write           = "1  0  1  0   1  1  0  0    1 0 1 x  x x x x",
                          "x  x  x  x   x  x  x  x    i i i i  i i i i";
    ;
;

#------------------------------------------------------------
# ATtiny13
#------------------------------------------------------------

part
    id                  = "t13";
    desc                = "ATtiny13";
    stk500_devcode      = 0x14;
    chip_erase_delay    = 4000;
    pgm_enable          = "1 0 1 0  1 1 0 0   0 1 0 1  0 0 1 1",
                          "x x x x  x x x x   x x x x  x x x x";

    chip_erase          = "1 0 1 0  1 1 0 0   1 0 0 x  x x x x",
                          "x x x x  x x x x   x x x x  x x x x";

    timeout		= 200;
    stabdelay		= 100;
    cmdexedelay		= 25;
    synchloops		= 32;
    bytedelay		= 0;
    pollindex		= 3;
    pollvalue		= 0x53;
    predelay		= 1;
    postdelay		= 1;
    pollmethod		= 1;

    memory "eeprom"
        size            = 64;
        min_write_delay = 4000;
        max_write_delay = 4000;
        readback_p1     = 0xff;
        readback_p2     = 0xff;
        read            = "1  0  1  0   0  0  0  0    0 0 0 x  x x x x",
                          "x  x a5 a4  a3 a2 a1 a0    o o o o  o o o o";

        write           = "1  1  0  0   0  0  0  0    0 0 0 x  x x x x",
                          "x  x a5 a4  a3 a2 a1 a0    i i i i  i i i i";

	mode		= 0x41;
	delay		= 5;
	blocksize	= 4;
	readsize	= 256;
    ;

    memory "flash"
        paged           = yes;
        size            = 1024;
        page_size       = 32;
        num_pages       = 32;
        min_write_delay = 4500;
        max_write_delay = 4500;
        readback_p1     = 0xff;
        readback_p2     = 0xff;
        read_lo         = "  0  0  1  0   0  0  0  0",
                          "  0  0  0  0   0  0  0 a8",
                          " a7 a6 a5 a4  a3 a2 a1 a0",
                          "  o  o  o  o   o  o  o  o";

        read_hi         = "  0  0  1  0   1  0  0  0",
                          "  0  0  0  0   0  0  0 a8",
                          " a7 a6 a5 a4  a3 a2 a1 a0",
                          "  o  o  o  o   o  o  o  o";

        loadpage_lo     = "  0  1  0  0   0  0  0  0",
                          "  0  0  0  x   x  x  x  x",
                          "  x  x  x  x  a3 a2 a1 a0",
                          "  i  i  i  i   i  i  i  i";

        loadpage_hi     = "  0  1  0  0   1  0  0  0",
                          "  0  0  0  x   x  x  x  x",
                          "  x  x  x  x  a3 a2 a1 a0",
                          "  i  i  i  i   i  i  i  i";

        writepage       = "  0  1  0  0   1  1  0  0",
                          "  0  0  0  0   0  0  0 a8",
                          " a7 a6 a5 a4   x  x  x  x",
                          "  x  x  x  x   x  x  x  x";

	mode		= 0x41;
	delay		= 6;
	blocksize	= 32;
	readsize	= 256;
    ;

    memory "signature"
        size            = 3;
        read            = "0  0  1  1   0  0  0  0    0 0 0 x  x x x x",
                          "x  x  x  x   x  x a1 a0    o o o o  o o o o";
    ;

    memory "lock"
        size            = 1;
        min_write_delay = 4500;
        max_write_delay = 4500;

	read            = "0  1  0  1   1  0  0  0    0 0 0 0  0 0 0 0",
                          "x  x  x  x   x  x  x  x    x x o o  o o o o";

        write           = "1  0  1  0   1  1  0  0    1 1 1 x  x x x x",
                          "x  x  x  x   x  x  x  x    1 1 i i  i i i i";
    ;

    memory "calibration"
        size            = 1;
        read            = "0  0  1  1   1  0  0  0    0 0 0 x  x x x x",
                          "0  0  0  0   0  0  0  0    o o o o  o o o o";
    ;

    memory "lfuse"
        size            = 1;
        min_write_delay = 4500;
        max_write_delay = 4500;

        write           = "1 0 1 0  1 1 0 0  1 0 1 0  0 0 0 0",
                          "x x x x  x x x x  i i i i  i i i i";

        read            = "0 1 0 1  0 0 0 0  0 0 0 0  0 0 0 0",
                          "x x x x  x x x x  o o o o  o o o o";
      ;

    memory "hfuse"
        size            = 1;
        min_write_delay = 4500;
        max_write_delay = 4500;

        write           = "1 0 1 0  1 1 0 0  1 0 1 0  1 0 0 0",
                          "x x x x  x x x x  i i i i  i i i i";

        read            = "0 1 0 1  1 0 0 0  0 0 0 0  1 0 0 0",
                          "x x x x  x x x x  o o o o  o o o o";
      ;

;


#------------------------------------------------------------
# ATtiny15
#------------------------------------------------------------

part
    id                  = "t15";
    desc                = "ATtiny15";
    stk500_devcode      = 0x13;
    avr910_devcode      = 0x56;
    chip_erase_delay    = 8200;
    pgm_enable          = "1 0 1 0  1 1 0 0   0 1 0 1  0 0 1 1",
                          "x x x x  x x x x   x x x x  x x x x";

    chip_erase          = "1 0 1 0  1 1 0 0   1 0 0 x  x x x x",
                          "x x x x  x x x x   x x x x  x x x x";

    timeout		= 200;
    stabdelay		= 100;
    cmdexedelay		= 25;
    synchloops		= 32;
    bytedelay		= 0;
    pollindex		= 3;
    pollvalue		= 0x53;
    predelay		= 1;
    postdelay		= 1;
    pollmethod		= 0;

    memory "eeprom"
        size            = 64;
        min_write_delay = 8200;
        max_write_delay = 8200;
        readback_p1     = 0xff;
        readback_p2     = 0xff;
        read            = "1  0  1  0   0  0  0  0    x x x x  x x x x",
                          "x  x a5 a4  a3 a2 a1 a0    o o o o  o o o o";

        write           = "1  1  0  0   0  0  0  0    x x x x  x x x x",
                          "x  x a5 a4  a3 a2 a1 a0    i i i i  i i i i";

	mode		= 0x04;
	delay		= 10;
	blocksize	= 64;
	readsize	= 256;
    ;

    memory "flash"
        size            = 1024;
        min_write_delay = 4100;
        max_write_delay = 4100;
        readback_p1     = 0xff;
        readback_p2     = 0xff;
        read_lo         = "  0  0  1  0   0  0  0  0",
                          "  x  x  x  x   x  x  x a8",
                          " a7 a6 a5 a4  a3 a2 a1 a0",
                          "  o  o  o  o   o  o  o  o";

        read_hi         = "  0  0  1  0   1  0  0  0",
                          "  x  x  x  x   x  x  x a8",
                          " a7 a6 a5 a4  a3 a2 a1 a0",
                          "  o  o  o  o   o  o  o  o";