lm75a_settings.xml

基于Freescale Codewarrior6.2环境下的针对qe8 单片机的LM75A温度传感器的驱动程序,可以直接使用

<PE_PROJECT_SETTINGS_DOCUMENTATION>
  <PE_product_version v="version 3.03 for Freescale HC(S)08/RS08/CFV1"/>
  <PE_core_version v="Processor Expert Version 0407"/>

  <CPU_Bean name="Cpu" type="MC9S08QE8_32">
    <Enabled v="N"/>

    <Properties>
      <Bean_name v="Cpu"/>
      <CPU_type v="MC9S08QE8CFM"/>
      <list name="Shared Internal properties" v="1">
      </list>
      <list name="Shared CGM module settings" v="1">
        <group name="Clock settings">
          <group name="Internal clock">
            <Internal_oscillator_frequency__kHz_ v="32.768000000000"/>
            <Internal_ref__clock_for_peripherals v="Enabled"/>
            <boolgroup name="Initialize trim value" v="no" />
          </group>
          <boolgroup name="External clock" v="Disabled" />
          <group name="Low-power modes settings">
            <boolgroup name="STOP instruction enabled" v="no" />
          </group>
        </group>
      </list>
      <Initialization_interrupt_priority v="interrupts enabled"/>
      <list name="Shared internal resource mapping - XDP512" v="1">
        <group name="Internal resource mapping">
          <group name="Interrupt vector table">
            <Address v="65486"/>
            <Size v="48"/>
          </group>
          <group name="Reset vector">
            <Address v="65534"/>
            <Size v="2"/>
          </group>
        </group>
      </list>
      <group name="Internal peripherals">
        <list name="Shared ADC settings" v="1">
          <group name="ADC">
            <Internal_bandgap_buffer v="Disabled"/>
          </group>
        </list>
        <list name="Shared BDM settings" v="1">
          <boolgroup name="BDM pin support" v="Disabled" />
        </list>
        <list name="Shared FLASH settings" v="1">
          <group name="FLASH">
            <enumgroup name="Security state" v="Disabled">
            </enumgroup>
            <enumgroup name="Protection" v="Disabled">
            </enumgroup>
            <Vector_redirection v="no"/>
          </group>
        </list>
        <list name="Included IO settings" v="1">
          <group name="I/O module">
            <list name="Shared Unused I/O" v="1">
              <enumgroup name="Initialize unused I/O pins" v="no initialization">
              </enumgroup>
            </list>
            <group name="PORT A">
              <Slew_rate_control_for_PTA0 v="no"/>
              <Slew_rate_control_for_PTA1 v="no"/>
              <Slew_rate_control_for_PTA2 v="no"/>
              <Slew_rate_control_for_PTA3 v="no"/>
              <Slew_rate_control_for_PTA4 v="no"/>
              <Slew_rate_control_for_PTA6 v="no"/>
              <Slew_rate_control_for_PTA7 v="no"/>
              <Drive_strength_for_PTA0 v="High"/>
              <Drive_strength_for_PTA1 v="High"/>
              <Drive_strength_for_PTA2 v="High"/>
              <Drive_strength_for_PTA3 v="High"/>
              <Drive_strength_for_PTA4 v="High"/>
              <Drive_strength_for_PTA6 v="High"/>
              <Drive_strength_for_PTA7 v="High"/>
            </group>
            <group name="PORT B">
              <Slew_rate_control_for_PTB0 v="no"/>
              <Slew_rate_control_for_PTB1 v="no"/>
              <Slew_rate_control_for_PTB2 v="no"/>
              <Slew_rate_control_for_PTB3 v="no"/>
              <Slew_rate_control_for_PTB4 v="no"/>
              <Slew_rate_control_for_PTB5 v="no"/>
              <Slew_rate_control_for_PTB6 v="no"/>
              <Slew_rate_control_for_PTB7 v="no"/>
              <Drive_strength_for_PTB0 v="High"/>
              <Drive_strength_for_PTB1 v="High"/>
              <Drive_strength_for_PTB2 v="High"/>
              <Drive_strength_for_PTB3 v="High"/>
              <Drive_strength_for_PTB4 v="High"/>
              <Drive_strength_for_PTB5 v="High"/>
              <Drive_strength_for_PTB6 v="High"/>
              <Drive_strength_for_PTB7 v="High"/>
            </group>
            <group name="PORT C">
              <Slew_rate_control_for_PTC0 v="no"/>
              <Slew_rate_control_for_PTC1 v="no"/>
              <Slew_rate_control_for_PTC2 v="no"/>
              <Slew_rate_control_for_PTC3 v="no"/>
              <Slew_rate_control_for_PTC4 v="no"/>
              <Slew_rate_control_for_PTC5 v="no"/>
              <Slew_rate_control_for_PTC6 v="no"/>
              <Slew_rate_control_for_PTC7 v="no"/>
              <Drive_strength_for_PTC0 v="High"/>
              <Drive_strength_for_PTC1 v="High"/>
              <Drive_strength_for_PTC2 v="High"/>
              <Drive_strength_for_PTC3 v="High"/>
              <Drive_strength_for_PTC4 v="High"/>
              <Drive_strength_for_PTC5 v="High"/>
              <Drive_strength_for_PTC6 v="High"/>
              <Drive_strength_for_PTC7 v="High"/>
            </group>
            <group name="PORT D">
              <Slew_rate_control_for_PTD0 v="no"/>
              <Slew_rate_control_for_PTD1 v="no"/>
              <Slew_rate_control_for_PTD2 v="no"/>
              <Slew_rate_control_for_PTD3 v="no"/>
              <Drive_strength_for_PTD0 v="High"/>
              <Drive_strength_for_PTD1 v="High"/>
              <Drive_strength_for_PTD2 v="High"/>
              <Drive_strength_for_PTD3 v="High"/>
            </group>
          </group>
        </list>
        <group name="System Clock Gating">
          <TPM1_Clock_Gate v="Enabled"/>
          <TPM2_Clock_Gate v="Enabled"/>
          <ADC_Clock_Gate v="Enabled"/>
          <IIC_Clock_Gate v="Enabled"/>
          <SCI_Clock_Gate v="Enabled"/>
          <DBG_Clock_Gate v="Enabled"/>
          <FLS_Clock_Gate v="Enabled"/>
          <IRQ_Clock_Gate v="Enabled"/>
          <KBI_Clock_Gate v="Enabled"/>
          <ACMP_Clock_Gate v="Enabled"/>
          <RTC_Clock_Gate v="Enabled"/>
          <SPI_Clock_Gate v="Enabled"/>
        </group>
        <list name="Shared LVD settings" v="1">
          <boolgroup name="LVD module" v="Enabled">
            <LVD_operation v="Reset"/>
            <LVW_interrupt v="Disabled"/>
            <boolgroup name="LVD module interrupt" v="Disabled" />
            <Enable_in_stop_mode v="yes"/>
            <Wake_up_on_Interupt v="no"/>
          </boolgroup>
        </list>
        <list name="Shared TMP modules setting" v="1">
        </list>
        <list name="Shared Reset pin setting" v="1">
          <boolgroup name="Reset pin support" v="Disabled" />
        </list>
      </group>
      <group name="CPU interrupts">
        <list name="Shared Cpu interrupts" v="1">
        </list>
        <list name="Shared Cpu interrupts" v="1">
          <boolgroup name="SWI" v="Disabled" />
        </list>
      </group>
      <list name="Shared ICSv3 speed mode settings" v="1">
        <group name="Enabled speed modes">
          <boolgroup name="High speed mode" v="Enabled">
            <High_speed_clock v="Internal Clock"/>
            <Bus_freq__divider v="Auto select"/>
            <Internal_bus_clock v="4.194304000000"/>
            <Fixed_frequency_clock__MHz_ v="0.016384"/>
            <enumgroup name="FLL mode" v="Engaged">
              <enumgroup name="Ref. clock source" v="Internal Clock">
                <Ref__clock_freq___MHz_ v="0.032768000000"/>
              </enumgroup>
              <enumgroup name="DCO mode" v="Auto select">
              </enumgroup>
              <FLL_output_clock_freq___MHz_ v="16.777216000000"/>
            </enumgroup>
          </boolgroup>
          <boolgroup name="Low speed mode" v="Disabled" />
          <boolgroup name="Slow speed mode" v="Disabled" />
        </group>
      </list>
    </Properties>

    <Methods>
      <list name="SharedCpuMethods" v="1">
        <SetHighSpeed v="don&apos;t generate code"/>
        <SetLowSpeed v="don&apos;t generate code"/>
        <SetSlowSpeed v="don&apos;t generate code"/>
        <GetSpeedMode v="don&apos;t generate code"/>
        <SetIntVect v="don&apos;t generate code"/>
        <GetIntVect v="don&apos;t generate code"/>
        <EnableInt v="generate code"/>
        <DisableInt v="generate code"/>
        <GetResetSource v="don&apos;t generate code"/>
        <SetWaitMode v="don&apos;t generate code"/>
        <SetStopMode v="don&apos;t generate code"/>
        <GetLowVoltageFlag v="don&apos;t generate code"/>
        <ClearLowVoltageFlag v="don&apos;t generate code"/>
        <GetLowVoltageWarningFlag v="don&apos;t generate code"/>
        <ClearLowVoltageWarningFlag v="don&apos;t generate code"/>
        <GetPartialPowerDownFlag v="don&apos;t generate code"/>
        <ClearPartialPowerDownFlag v="don&apos;t generate code"/>
        <GetIdentification v="don&apos;t generate code"/>
        <SetBackdoorKey v="don&apos;t generate code"/>
        <Delay100US v="don&apos;t generate code"/>
      </list>
    </Methods>

    <Events>
      <Event_module_name v="Events"/>
      <list name="HCS08EventsGrp" v="1">
        <event name="OnSwINT" v="don&apos;t generate code" />
      </list>
      <list name="CommonEventsGrp" v="1">
        <event name="OnReset" v="don&apos;t generate code" />
        <event name="OnLvdINT" v="don&apos;t generate code" />
        <event name="OnLvwINT" v="don&apos;t generate code" />
      </list>
    </Events>
    <Compiler v="CodeWarrior HCS08 C Compiler"/>

    <CompilerProperties>
      <Compiler v="CodeWarrior HCS08 C Compiler"/>
      <Generate_macros v="yes"/>
      <group name="User initialization">
        <User_data_declarations>
        </User_data_declarations>
        <User_code_before_PE_initialization>
        </User_code_before_PE_initialization>
        <User_code_after_PE_initialization>
        </User_code_after_PE_initialization>
      </group>
      <Memory_model v="Small"/>
      <boolgroup name="Generate PRM file" v="yes">
        <enumgroup name="Stack specification" v="size">
          <Stack_size v="128"/>
        </enumgroup>
        <Set_memory_areas_default v="Click to set default &gt;"/>
        <list name="ROM/RAM Areas" v="0">
        </list>
      </boolgroup>
    </CompilerProperties>
  </CPU_Bean>

  <CPU_Bean name="Cpu" type="MC9S08QE8_32">
    <Enabled v="Y"/>

    <Properties>
      <Bean_name v="Cpu"/>
      <CPU_type v="MC9S08QE8CFM"/>
      <list name="Shared Internal properties" v="1">
      </list>
      <list name="Shared CGM module settings" v="1">
        <group name="Clock settings">
          <group name="Internal clock">
            <Internal_oscillator_frequency__kHz_ v="32.768000000000"/>
            <Internal_ref__clock_for_peripherals v="Enabled"/>
            <boolgroup name="Initialize trim value" v="no" />
          </group>
          <boolgroup name="External clock" v="Disabled" />
          <group name="Low-power modes settings">
            <boolgroup name="STOP instruction enabled" v="no" />
          </group>
        </group>
      </list>
      <Initialization_interrupt_priority v="interrupts enabled"/>
      <list name="Shared internal resource mapping - XDP512" v="1">
        <group name="Internal resource mapping">
          <group name="Interrupt vector table">
            <Address v="65486"/>
            <Size v="48"/>
          </group>
          <group name="Reset vector">
            <Address v="65534"/>
            <Size v="2"/>
          </group>
        </group>
      </list>
      <group name="Internal peripherals">
        <list name="Shared ADC settings" v="1">
          <group name="ADC">
            <Internal_bandgap_buffer v="Disabled"/>
          </group>
        </list>
        <list name="Shared BDM settings" v="1">
          <boolgroup name="BDM pin support" v="Enabled">
            <BDM_pin v="PTA4_ACMP1O_BKGD_MS"/>
            <BDM_pin_signal v=""/>
          </boolgroup>
        </list>
        <list name="Shared FLASH settings" v="1">
          <group name="FLASH">
            <enumgroup name="Security state" v="Disabled">
            </enumgroup>
            <enumgroup name="Protection" v="Disabled">
            </enumgroup>
            <Vector_redirection v="no"/>
          </group>
        </list>
        <list name="Included IO settings" v="1">
          <group name="I/O module">
            <list name="Shared Unused I/O" v="1">
              <enumgroup name="Initialize unused I/O pins" v="no initialization">
              </enumgroup>
            </list>