flash.c

从Luminary官方网站下载的LM3S6000系列的UCos+Tcp/IP的源码, 经本人稍微修改后可直接在IAR6.2下编译通过,里面包括了LM3S6000系列的所有外设UART, PWn....

            // We're done handling this protection.
            //
            break;
        }

        //
        // Make this block read only.
        //
        case FlashReadOnly:
        {
            //
            // The block can not be made read only if it is execute only.
            //
            if(((ulProtectRE >> ulAddress) & FLASH_FMP_BLOCK_0) !=
               FLASH_FMP_BLOCK_0)
            {
                return(-1);
            }

            //
            // Make this block read only.
            //
            ulProtectPE &= ~(FLASH_FMP_BLOCK_0 << ulAddress);

            //
            // We're done handling this protection.
            //
            break;
        }

        //
        // Make this block read/write.
        //
        case FlashReadWrite:
        default:
        {
            //
            // The block can not be made read/write if it is not already
            // read/write.
            //
            if((((ulProtectRE >> ulAddress) & FLASH_FMP_BLOCK_0) !=
                FLASH_FMP_BLOCK_0) ||
               (((ulProtectPE >> ulAddress) & FLASH_FMP_BLOCK_0) !=
                FLASH_FMP_BLOCK_0))
            {
                return(-1);
            }

            //
            // The block is already read/write, so there is nothing to do.
            //
            return(0);
        }
    }

    //
    // For Stellaris Base Device 0, Rev C1, the upper bits of the FMPPE
    // register are used for JTAG options, and are not available for the
    // FLASH protection scheme.  When Setting Block Protection, ensure that
    // these bits are not altered.
    //
    if(IS_BASE0_REVC1())
    {
        ulProtectRE &= ~(FLASH_FMP_BLOCK_31 | FLASH_FMP_BLOCK_30);
        ulProtectRE |= (HWREG(g_pulFMPRERegs[ulBank]) & 
                (FLASH_FMP_BLOCK_31 | FLASH_FMP_BLOCK_30));
    }

    //
    // Set the new protection for the specified flash bank.
    //
    HWREG(g_pulFMPRERegs[ulBank]) = ulProtectRE;
    HWREG(g_pulFMPPERegs[ulBank]) = ulProtectPE;
    
    //
    // Success.
    //
    return(0);
}

//*****************************************************************************
//
//! Saves the flash protection settings.
//!
//! This function will make the currently programmed flash protection settings
//! permanent.  This is a non-reversible operation; a chip reset or power cycle
//! will not change the flash protection.
//!
//! This function will not return until the protection has been saved.
//!
//! \return Returns 0 on success, or -1 if a hardware error is encountered.
//
//*****************************************************************************
long
FlashProtectSave(void)
{
    int ulTemp, ulLimit;

    //
    // If running on Base 0 device, only trigger a save of the first
    // two protection registers (FMPRE and FMPPE).  Otherwise, save the
    // entire bank of flash protection registers.
    // 
    ulLimit = IS_BASE1() ? 8 : 2;
    for(ulTemp = 0; ulTemp < ulLimit; ulTemp++)
    {
        //
        // Tell the flash controller to write the flash protection register.
        //
        HWREG(FLASH_FMA) = ulTemp;
        HWREG(FLASH_FMC) = FLASH_FMC_WRKEY | FLASH_FMC_COMT;

        //
        // Wait until the write has completed.
        //
        while(HWREG(FLASH_FMC) & FLASH_FMC_COMT)
        {
        }
    }
    
    //
    // Success.
    //
    return(0);
}

//*****************************************************************************
//
//! Gets the User Registers
//!
//! \param pulUser0 is a pointer to the location to store USER Register 0.
//! \param pulUser1 is a pointer to the location to store USER Register 1.
//!
//! This function will read the contents of User Registers (0 and 1), and
//! store them in the specified locations.
//!
//! \return Returns 0 on success, or -1 if a hardware error is encountered.
//
//*****************************************************************************
long
FlashUserGet(unsigned long *pulUser0, unsigned long *pulUser1)
{
    //
    // Verify that the pointers are valid.
    //
    ASSERT(pulUser0 != 0);
    ASSERT(pulUser1 != 0);

    //
    // Verify that hardware supports User Registers.
    //
    if(!IS_BASE1())
    {
        return(-1);
    }

    //
    // Get and store the current value of the User Registers.
    //
    *pulUser0 = HWREG(SYSCTL_USER0);
    *pulUser1 = HWREG(SYSCTL_USER1);

    //
    // Success.
    //
    return(0);
}

//*****************************************************************************
//
//! Sets the User Registers
//!
//! \param ulUser0 is the value to store in USER Register 0.
//! \param ulUser1 is the value to store in USER Register 1.
//!
//! This function will set the contents of the User Registers (0 and 1) to
//! the specified values.
//!
//! \return Returns 0 on success, or -1 if a hardware error is encountered.
//
//*****************************************************************************
long
FlashUserSet(unsigned long ulUser0, unsigned long ulUser1)
{
    //
    // Verify that hardware supports User Registers.
    //
    if(!IS_BASE1())
    {
        return(-1);
    }

    //
    // Save the new values into the User Registers.
    //
    HWREG(SYSCTL_USER0) = ulUser0;
    HWREG(SYSCTL_USER1) = ulUser1;

    //
    // Success.
    //
    return(0);
}

//*****************************************************************************
//
//! Saves the User Registers
//!
//! This function will make the currently programmed User register settings
//! permanent.  This is a non-reversible operation; a chip reset or power cycle
//! will not change this setting.
//!
//! This function will not return until the protection has been saved.
//!
//! \return Returns 0 on success, or -1 if a hardware error is encountered.
//
//*****************************************************************************
long
FlashUserSave(void)
{
    //
    // Verify that hardware supports User Registers.
    //
    if(!IS_BASE1())
    {
        return(-1);
    }

    //
    // Setting the MSB of FMA will trigger a permanent save of a USER
    // register.  Bit 0 will indicate User 0 (0) or User 1 (1).
    //
    HWREG(FLASH_FMA) = 0x80000000;
    HWREG(FLASH_FMC) = FLASH_FMC_WRKEY | FLASH_FMC_COMT;

    //
    // Wait until the write has completed.
    //
    while(HWREG(FLASH_FMC) & FLASH_FMC_COMT)
    {
    }

    //
    // Tell the flash controller to write the USER1 Register.
    //
    HWREG(FLASH_FMA) = 0x80000001;
    HWREG(FLASH_FMC) = FLASH_FMC_WRKEY | FLASH_FMC_COMT;

    //
    // Wait until the write has completed.
    //
    while(HWREG(FLASH_FMC) & FLASH_FMC_COMT)
    {
    }
    
    //
    // Success.
    //
    return(0);
}

//*****************************************************************************
//
//! Registers an interrupt handler for the flash interrupt.
//!
//! \param pfnHandler is a pointer to the function to be called when the flash
//! interrupt occurs.
//!
//! This sets the handler to be called when the flash interrupt occurs.  The
//! flash controller can generate an interrupt when an invalid flash access
//! occurs, such as trying to program or erase a read-only block, or trying to
//! read from an execute-only block.  It can also generate an interrupt when a
//! program or erase operation has completed.  The interrupt will be
//! automatically enabled when the handler is registered.
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \return None.
//
//*****************************************************************************
void
FlashIntRegister(void (*pfnHandler)(void))
{
    //
    // Register the interrupt handler, returning an error if an error occurs.
    //
    IntRegister(INT_FLASH, pfnHandler);

    //
    // Enable the flash interrupt.
    //
    IntEnable(INT_FLASH);
}

//*****************************************************************************
//
//! Unregisters the interrupt handler for the flash interrupt.
//!
//! This function will clear the handler to be called when the flash interrupt
//! occurs.  This will also mask off the interrupt in the interrupt controller
//! so that the interrupt handler is no longer called.
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \return None.
//
//*****************************************************************************
void
FlashIntUnregister(void)
{
    //
    // Disable the interrupt.
    //
    IntDisable(INT_FLASH);

    //
    // Unregister the interrupt handler.
    //
    IntUnregister(INT_FLASH);
}

//*****************************************************************************
//
//! Enables individual flash controller interrupt sources.
//!
//! \param ulIntFlags is a bit mask of the interrupt sources to be enabled.
//! Can be any of the \b FLASH_FCIM_PROGRAM or \b FLASH_FCIM_ACCESS values.
//!
//! Enables the indicated flash controller interrupt sources.  Only the sources
//! that are enabled can be reflected to the processor interrupt; disabled
//! sources have no effect on the processor.
//!
//! \return None.
//
//*****************************************************************************
void
FlashIntEnable(unsigned long ulIntFlags)
{
    //
    // Enable the specified interrupts.
    //
    HWREG(FLASH_FCIM) |= ulIntFlags;
}

//*****************************************************************************
//
//! Disables individual flash controller interrupt sources.
//!
//! \param ulIntFlags is a bit mask of the interrupt sources to be disabled.
//! Can be any of the \b FLASH_FCIM_PROGRAM or \b FLASH_FCIM_ACCESS values.
//!
//! Disables the indicated flash controller interrupt sources.  Only the
//! sources that are enabled can be reflected to the processor interrupt;
//! disabled sources have no effect on the processor.
//!
//! \return None.
//
//*****************************************************************************
void
FlashIntDisable(unsigned long ulIntFlags)
{
    //
    // Disable the specified interrupts.
    //
    HWREG(FLASH_FCIM) &= ~(ulIntFlags);
}

//*****************************************************************************
//
//! Gets the current interrupt status.
//!
//! \param bMasked is false if the raw interrupt status is required and true if
//! the masked interrupt status is required.
//!
//! This returns the interrupt status for the flash controller.  Either the raw
//! interrupt status or the status of interrupts that are allowed to reflect to
//! the processor can be returned.
//!
//! \return The current interrupt status, enumerated as a bit field of
//! \b FLASH_FCMISC_PROGRAM and \b FLASH_FCMISC_ACCESS.
//
//*****************************************************************************
unsigned long
FlashIntGetStatus(tBoolean bMasked)
{
    //
    // Return either the interrupt status or the raw interrupt status as
    // requested.
    //
    if(bMasked)
    {
        return(HWREG(FLASH_FCMISC));
    }
    else
    {
        return(HWREG(FLASH_FCRIS));
    }
}

//*****************************************************************************
//
//! Clears flash controller interrupt sources.
//!
//! \param ulIntFlags is the bit mask of the interrupt sources to be cleared.
//! Can be any of the \b FLASH_FCMISC_PROGRAM or \b FLASH_FCMISC_ACCESS
//! values.
//!
//! The specified flash controller interrupt sources are cleared, so that they
//! no longer assert.  This must be done in the interrupt handler to keep it
//! from being called again immediately upon exit.
//!
//! \return None.
//
//*****************************************************************************
void
FlashIntClear(unsigned long ulIntFlags)
{
    //
    // Clear the flash interrupt.
    //
    HWREG(FLASH_FCMISC) = ulIntFlags;
}

//*****************************************************************************
//
// Close the Doxygen group.
//! @}
//
//*****************************************************************************