ax88796.h

来自「PXA255 WINCE 4.2 BSP ,该BSP是商用的。」· C头文件 代码 · 共 105 行

// Generic 8390 ethernet controller driver

#define ETHER_ADDR_LEN 6

// The 8390 specific per-packet-header format
struct e8390_pkt_hdr {
	unsigned char status;	// status
	unsigned char next;	// pointer to next packet
	unsigned short count;	// header + packet length in bytes
};

/* Some generic ethernet register configurations. */
#define E8390_TX_IRQ_MASK	0xa	/* For register EN0_ISR */
#define E8390_RX_IRQ_MASK	0x5
#define E8390_RXCONFIG		0x44	/* EN0_RXCR: broadcasts, no multicast,errors */
#define E8390_RXOFF		0x60	/* EN0_RXCR: Accept no packets */
#define E8390_TXCONFIG	0x00	/* EN0_TXCR: Normal transmit mode */
#define E8390_TXOFF		0x02	/* EN0_TXCR: Transmitter off */

/*  Register accessed at EN_CMD, the 8390 base addr.  */
#define E8390_STOP		0x01	/* Stop and reset the chip */
#define E8390_START		0x02	/* Start the chip, clear reset */
#define E8390_TRANS		0x04	/* Transmit a frame */
#define E8390_RREAD		0x08	/* Remote read */
#define E8390_RWRITE		0x10	/* Remote write  */
#define E8390_NODMA		0x20	/* Remote DMA */
#define E8390_PAGE0		0x00	/* Select page chip registers */
#define E8390_PAGE1		0x40	/* using the two high-order bits */
#define E8390_PAGE2		0x80	/* Page 3 is invalid. */

#define EI_SHIFT(x)	((x)<<1)

#define E8390_CMD		EI_SHIFT(0x00)  /* The command register (for all pages) */
/* Page 0 register offsets. */
#define EN0_CLDALO		EI_SHIFT(0x01)	/* Low byte of current local dma addr  RD */
#define EN0_STARTPG		EI_SHIFT(0x01)	/* Starting page of ring bfr WR */
#define EN0_CLDAHI		EI_SHIFT(0x02)	/* High byte of current local dma addr  RD */
#define EN0_STOPPG		EI_SHIFT(0x02)	/* Ending page +1 of ring bfr WR */
#define EN0_BOUNDARY		EI_SHIFT(0x03)	/* Boundary page of ring bfr RD WR */
#define EN0_TSR			EI_SHIFT(0x04)	/* Transmit status reg RD */
#define EN0_TPSR		EI_SHIFT(0x04)	/* Transmit starting page WR */
#define EN0_NCR			EI_SHIFT(0x05)	/* Number of collision reg RD */
#define EN0_TCNTLO		EI_SHIFT(0x05)	/* Low  byte of tx byte count WR */
#define EN0_FIFO		EI_SHIFT(0x06)	/* FIFO RD */
#define EN0_TCNTHI		EI_SHIFT(0x06)	/* High byte of tx byte count WR */
#define EN0_ISR			EI_SHIFT(0x07)	/* Interrupt status reg RD WR */
#define EN0_CRDALO		EI_SHIFT(0x08)	/* low byte of current remote dma address RD */
#define EN0_RSARLO		EI_SHIFT(0x08)	/* Remote start address reg 0 */
#define EN0_CRDAHI		EI_SHIFT(0x09)	/* high byte, current remote dma address RD */
#define EN0_RSARHI		EI_SHIFT(0x09)	/* Remote start address reg 1 */
#define EN0_RCNTLO		EI_SHIFT(0x0a)	/* Remote byte count reg WR */
#define EN0_RCNTHI		EI_SHIFT(0x0b)	/* Remote byte count reg WR */
#define EN0_RSR			EI_SHIFT(0x0c)	/* rx status reg RD */
#define EN0_RXCR		EI_SHIFT(0x0c)	/* RX configuration reg WR */
#define EN0_TXCR		EI_SHIFT(0x0d)	/* TX configuration reg WR */
#define EN0_COUNTER0		EI_SHIFT(0x0d)	/* Rcv alignment error counter RD */
#define EN0_DCFG		EI_SHIFT(0x0e)	/* Data configuration reg WR */
#define EN0_COUNTER1		EI_SHIFT(0x0e)	/* Rcv CRC error counter RD */
#define EN0_IMR			EI_SHIFT(0x0f)	/* Interrupt mask reg WR */
#define EN0_COUNTER2		EI_SHIFT(0x0f)	/* Rcv missed frame error counter RD */
#define EN0_GPI			EI_SHIFT(0x17)  /* General purpose input register */

/* Bits in EN0_ISR - Interrupt status register */
#define ENISR_RX		0x01	/* Receiver, no error */
#define ENISR_TX		0x02	/* Transmitter, no error */
#define ENISR_RX_ERR		0x04	/* Receiver, with error */
#define ENISR_TX_ERR		0x08	/* Transmitter, with error */
#define ENISR_OVER		0x10	/* Receiver overwrote the ring */
#define ENISR_COUNTERS		0x20	/* Counters need emptying */
#define ENISR_RDC		0x40	/* remote dma complete */
#define ENISR_RESET		0x80	/* Reset completed */
#define ENISR_ALL		(ENISR_RX|ENISR_TX|ENISR_RX_ERR|ENISR_TX_ERR)	/* Interrupts we will enable */

/* Bits in EN0_DCFG - Data config register */
#define ENDCFG_WTS		0x01	/* word transfer mode selection */
#define ENDCFG_BOS		0x02	/* byte order selection */

/* Page 1 register offsets. */
#define EN1_PHYS		EI_SHIFT(0x01)	/* This board's physical enet addr RD WR */
#define EN1_PHYS_SFT(i)		EI_SHIFT(i+1) /* Get and set mac address */
#define EN1_CURPAG		EI_SHIFT(0x07)	/* Current memory page RD WR */
#define EN1_MULT		EI_SHIFT(0x08)	/* Multicast filter mask array (8 bytes) RD WR */
#define EN1_MULT_SFT(i)		EI_SHIFT(8+i) /* Get and set multicast filter */

/* Bits in received packet status byte and EN0_RSR*/
#define ENRSR_RXOK		0x01	/* Received a good packet */
#define ENRSR_CRC		0x02	/* CRC error */
#define ENRSR_FAE		0x04	/* frame alignment error */
#define ENRSR_FO		0x08	/* FIFO overrun */
#define ENRSR_MPA		0x10	/* missed pkt */
#define ENRSR_PHY		0x20	/* physical/multicast address */
#define ENRSR_DIS		0x40	/* receiver disable. set in monitor mode */
#define ENRSR_DEF		0x80	/* deferring */

/* Transmitted packet status, EN0_TSR. */
#define ENTSR_PTX		0x01	/* Packet transmitted without error */
#define ENTSR_ND		0x02	/* The transmit wasn't deferred. */
#define ENTSR_COL		0x04	/* The transmit collided at least once. */
#define ENTSR_ABT		0x08  /* The transmit collided 16 times, and was deferred. */
#define ENTSR_CRS		0x10	/* The carrier sense was lost. */
#define ENTSR_FU		0x20  /* A "FIFO underrun" occurred during transmit. */
#define ENTSR_CDH		0x40	/* The collision detect "heartbeat" signal was lost. */
#define ENTSR_OWC		0x80  /* There was an out-of-window collision. */