hal_edb7xxx.h

来自「eCos操作系统源码」· C头文件 代码 · 共 407 行 · 第 1/2 页

#ifndef CYGONCE_HAL_EDB7XXX_H
#define CYGONCE_HAL_EDB7XXX_H

/*=============================================================================
//
//      hal_edb7xxx.h
//
//      HAL Support for Kernel Diagnostic Routines
//
//=============================================================================
//####ECOSGPLCOPYRIGHTBEGIN####
// -------------------------------------------
// This file is part of eCos, the Embedded Configurable Operating System.
// Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
//
// eCos is free software; you can redistribute it and/or modify it under
// the terms of the GNU General Public License as published by the Free
// Software Foundation; either version 2 or (at your option) any later version.
//
// eCos is distributed in the hope that it will be useful, but WITHOUT ANY
// WARRANTY; without even the implied warranty of MERCHANTABILITY or
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
// for more details.
//
// You should have received a copy of the GNU General Public License along
// with eCos; if not, write to the Free Software Foundation, Inc.,
// 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
//
// As a special exception, if other files instantiate templates or use macros
// or inline functions from this file, or you compile this file and link it
// with other works to produce a work based on this file, this file does not
// by itself cause the resulting work to be covered by the GNU General Public
// License. However the source code for this file must still be made available
// in accordance with section (3) of the GNU General Public License.
//
// This exception does not invalidate any other reasons why a work based on
// this file might be covered by the GNU General Public License.
//
// Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
// at http://sources.redhat.com/ecos/ecos-license/
// -------------------------------------------
//####ECOSGPLCOPYRIGHTEND####
//=============================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):    gthomas
// Contributors: gthomas
// Date:         1999-04-19
// Purpose:      Cirrus Logic EDB7XXX hardware description
// Description:
// Usage:        #include <cyg/hal/hal_edb7xxx.h>
//
//####DESCRIPTIONEND####
//
//===========================================================================*/

// Note: these defintions match the documentation, thus no attempt is made
// to sanitise (mangle) the names.  Also, care should be taken to keep this
// clean for use in assembly code (no "C" constructs).

// Comment above notwithstanding, this is needed for the clock UART_DIVISOR
// selection below.
#include <pkgconf/hal_arm_edb7xxx.h>

#define PADR    0x80000000 // Port A data register
#define PBDR    0x80000001 // Port B data register
#define PDDR    0x80000003 // Port D data register
#define PADDR   0x80000040 // Port A data direction register
#define PBDDR   0x80000041 // Port B data direction register
#define PDDDR   0x80000043 // Port D data direction register
#define PEDR    0x80000080 // Port E data register
#define PEDDR   0x800000C0 // Port E data direction register

#define SYSCON1 0x80000100 // System control register #1
#define SYSCON1_KBD_CTL     0xF // Keyboard scan - mask
#define SYSCON1_KBD_HIGH      0 // Keyboard scan - all columns high
#define SYSCON1_KBD_LOW       1 // Keyboard scan - all columns low
#define SYSCON1_KBD_TRISTATE  2 // Keyboard scan - all columns tri-state
#define SYSCON1_KBD_COL(n) (n+8)// Keyboard scan - select column 'n'
#define SYSCON1_TC1M    (1<<4)  // Timer/counter #1 - prescale mode
#define SYSCON1_TC1S    (1<<5)  // Timer/counter #1 - source (1=512KHz,0=2KHz)
#define SYSCON1_TC2M    (1<<6)  // Timer/counter #2 - prescale mode
#define SYSCON1_TC2S    (1<<7)  // Timer/counter #2 - source (1=512KHz,0=2KHz)
#define SYSCON1_UART1EN (1<<8)  // UART #1 enable
#define SYSCON1_BZTOG   (1<<9)  // Buzzer bit
#define SYSCON1_BZMOD   (1<<10) // Buzzer mode (0=direct,1=TC1)
#define SYSCON1_DBGEN   (1<<11) // Enable debug mode
#define SYSCON1_LCDEN   (1<<12) // Enable LCD
#define SYSCON1_CDENTX  (1<<13) // Enable Tx on CODEC
#define SYSCON1_CDENRX  (1<<14) // Enable Rx on CODEC
#define SYSCON1_SIREN   (1<<15) // Enable SIR protocol on UART #1
#define SYSCON1_ADCKSEL (3<<16) // Microwire clock
#define SYSCON1_ADC_CLOCK_4kHZ    (0<<16)
#define SYSCON1_ADC_CLOCK_16kHZ   (1<<16)
#define SYSCON1_ADC_CLOCK_64kHZ   (2<<16)
#define SYSCON1_ADC_CLOCK_128kHZ  (3<<16)
#define SYSCON1_EXCKEN  (1<<18) // External expansion clock enable
#define SYSCON1_WAKEDIS (1<<19) // Disable wakeup from snooze (do not disturb)
#define SYSCON1_IRTXM   (1<<20) // IrDA Tx mode

#define SYSCON2 0x80001100 // System control register #2
#define SYSCON2_SERSEL  (1<<0)  // 0=master/slave SSI, 1=CODEC
#define SYSCON2_KBD6    (1<<1)  // 0=8 bit keyboard, 1=6 bit
#define SYSCON2_DRAMSZ  (1<<2)  // DRAM width 0=32, 1=16
#define SYSCON2_KBWEN   (1<<3)  // 1=allow wake up from keyboard
#define SYSCON2_SS2TXEN (1<<4)  // Enable Tx on SS2
#define SYSCON2_PCMCIA1 (1<<5)  // Enable PCMCIA slot #1
#define SYSCON2_PCMCIA2 (1<<6)  // Enable PCMCIA slot #2
#define SYSCON2_SS2RXEN (1<<7)  // Enable Rx on SS2
#define SYSCON2_UART2EN (1<<8)  // Enable UART #2
#define SYSCON2_SS2MAEN (1<<9)  // Enable master mode on SS2
#define SYSCON2_SNZPOL  (1<<10) // Polarity of LCD during snooze
#define SYSCON2_LCDSNZE (1<<11)
#define SYSCON2_OSTB    (1<<12) // Operating system timing 0=512KHz, 1=500KHz
#define SYSCON2_CLKENSL (1<<13) // Source of run/clken signal 0=CLKEN, 1=RUN
#define SYSCON2_BUZFREQ (1<<14) // Buzzer frequency 0=timer, 1=fixed PLL/xtal

#define SYSCON3 0x80002200 // System control #3
#define SYSCON3_ADCCON    (1<<0) // ADC enable
#define SYSCON3_CLKCTL(n) (n<<1) // Processor block speed ((n+1)*18.432)MHz
#if defined(__EDB7209)
#define SYSCON3_I2SSEL    (1<<3) // Enable i2s instead of ssi#2
#define SYSCON3_FASTWAKE  (1<<8) // Determines wakeup in relationship
                                 //    to the 4 kHZ or 8 Hz clock
#define SYSCON3_DAIEN     (1<<9) // Enables the DAI
#endif
#if defined(__EDB7312) || defined(__EDB7209)
#define SYSCON3_ADCCKNSEN    (1<<4)  // Determines on which edge ADC
                                     // data is transmitted and read
                                     // in relationship to ADCCLK
#if defined(__EDB7312)
#define SYSCON3_DAISEL    (1<<3)  // Enable DAI instead of SSI
#define SYSCON3_128FS     (1<<9)  // Select DAI frame size
#define SYSCON3_ENPD67    (1<<10) // Configures Port D bits 6 and 7
#endif
#endif

#define SYSFLG1 0x80000140 // System flags #1
#define SYSFLG1_MCDR     (1<<0) // Media changed - direct read
#define SYSFLG1_DCDET    (1<<1) // 0=mains power, 1=battery
#define SYSFLG1_WUDR     (1<<2) // Wakeup direct
#define SYSFLG1_WUON     (1<<3) // Woken up
#define SYSFLG1_DID      (0xF<<4) // Display ID
#define SYSFLG1_CTS      (1<<8) // UART1 CTS
#define SYSFLG1_DSR      (1<<9) // UART1 DSR
#define SYSFLG1_DCD      (1<<10) // UART1 DCD
#define SYSFLG1_UBUSY1   (1<<11) // UART1 Tx busy
#define SYSFLG1_NBFLG    (1<<12) // New battery flag
#define SYSFLG1_RSTFLG   (1<<13) // Reset (button) flag
#define SYSFLG1_PFFLG    (1<<14) // Power fail flag
#define SYSFLG1_CLDFLG   (1<<15) // Cold start flag
#define SYSFLG1_RTCDIV   (0x3F<<16) // Real time clock divider (counter)
#define SYSFLG1_URXFE1   (1<<22) // UART1 Rx FIFO empty
#define SYSFLG1_UTXFF1   (1<<23) // UART1 Tx FIFO full
#define SYSFLG1_CRXFE    (1<<24) // CODEC Rx FIFO empty
#define SYSFLG1_CTXFF    (1<<25) // CODEC Tx FIFO full
#define SYSFLG1_SSIBUSY  (1<<26) // Synchronous serial interface busy
#define SYSFLG1_BOOTBITS (3<<27) // Boot mode (0=32,1=8,2=16,3=XX)
#define SYSFLG1_ID       (1<<29) // ID=1
#define SYSFLG1_VERID    (3<<30) // Board version

#define SYSFLG2 0x80001140 // System flags #2

#ifdef __EDB7312
#define SDCONF 0x80002300  // SDRAM configuration
#define SDRFOR 0x80002340  // SDRAM refresh
#endif

#define INTSR1  0x80000240 // Interrupt status register #1
#define INTSR1_EXTFIQ  (1<<0)  // External fast interrupt
#define INTSR1_BLINT   (1<<1)  // Battery low interrupt
#define INTSR1_WEINT   (1<<2)  // Watchdog expired interrupt
#define INTSR1_MCINT   (1<<3)  // Media changed interrupt
#define INTSR1_CSINT   (1<<4)  // CODEC sound interrupt
#define INTSR1_EINT1   (1<<5)  // External interrupt #1
#define INTSR1_EINT2   (1<<6)  // External interrupt #2
#define INTSR1_EINT3   (1<<7)  // External interrupt #3
#define INTSR1_TC1OI   (1<<8)  // Timer/counter #1 underflow
#define INTSR1_TC2OI   (1<<9)  // Timer/counter #2 underflow
#define INTSR1_RTCMI   (1<<10) // Real time clock match
#define INTSR1_TINT    (1<<11) // 64Hz tick
#define INTSR1_UTXINT1 (1<<12) // UART1 Tx interrupt
#define INTSR1_URXINT1 (1<<13) // UART1 Rx interrupt
#define INTSR1_UMSINT  (1<<14) // UART1 modem line change
#define INTSR1_SSEOTI  (1<<15) // Synchronous serial end of transfer
#define INTMR1  0x80000280 // Interrupt mask register #1

#define INTSR2  0x80001240 // Interrupt status #2
#define INTSR2_KBDINT  (1<<0)  // Keyboard interrupt
#define INTSR2_SS2RX   (1<<1)  // Synchronous serial #2 Rx
#define INTSR2_SS2TX   (1<<2)  // Synchronous serial #2 Tx
#define INTSR2_UTXINT2 (1<<12) // UART #2 Tx interrupt
#define INTSR2_URXINT2 (1<<13) // UART #2 Rx interrupt
#define INTMR2  0x80001280 // Interrupt mask #2

#define INTSR3  0x80002240 // Interrupt status #3
#if defined(__EDB7211)
#define INTSR3_MCPINT (1<<0) // MCP interrupt
#endif
#if defined(__EDB7209)
#define INTSR3_I2SINT (1<<0) // I2S interface interrupt
#endif
#if defined(__EDB7312)
#define INTSR3_DAIINT (1<<0) // DAI interface interrupt