notes_cygmon_pid

eCos操作系统源码

===========================================================================
#####ECOSGPLCOPYRIGHTBEGIN####
## -------------------------------------------
## This file is part of eCos, the Embedded Configurable Operating System.
## Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
##
## eCos is free software; you can redistribute it and/or modify it under
## the terms of the GNU General Public License as published by the Free
## Software Foundation; either version 2 or (at your option) any later version.
##
## eCos is distributed in the hope that it will be useful, but WITHOUT ANY
## WARRANTY; without even the implied warranty of MERCHANTABILITY or
## FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
## for more details.
##
## You should have received a copy of the GNU General Public License along
## with eCos; if not, write to the Free Software Foundation, Inc.,
## 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
##
## As a special exception, if other files instantiate templates or use macros
## or inline functions from this file, or you compile this file and link it
## with other works to produce a work based on this file, this file does not
## by itself cause the resulting work to be covered by the GNU General Public
## License. However the source code for this file must still be made available
## in accordance with section (3) of the GNU General Public License.
##
## This exception does not invalidate any other reasons why a work based on
## this file might be covered by the GNU General Public License.
##
## Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
## at http://sources.redhat.com/ecos/ecos-license/
## -------------------------------------------
#####ECOSGPLCOPYRIGHTEND####
===========================================================================

28 Jan 2000

How to build and install CygMon on the PID

Make CygMon image
~~~~~~~~~~~~~~~~~

Configure and build using the 'cygmon' template for the PID
target. These are the necessary CLI instructions. It can also be done
from the Configtool by selecting the appropriate templates.

 % cd /tmp
 % mkdir cygmon
 % cd cygmon
 % ecosconfig new pid cygmon
 % ecosconfig tree
 % make

This will install some files in ./install/bin:

 cygmon.elf:   The built CygMon image
 cygmon.bin:   The image converted to binary (suitable for burning to ROM)
 cygmon.img:   The relocated ELF image (suitable for FLASH writing, see below)
 cygmon.srec:  The image converted to srecords

Make FLASH tool
~~~~~~~~~~~~~~~

Again, these are the necessary CLI instructions. It can also be done
from the Configtool by selecting the appropriate templates, and
enabling the option.

 % cd /tmp
 % mkdir pid-flash
 % cd pid-flash
 % ecosconfig new pid
 % <edit ecos.ecc, enabling the CYGBLD_BUILD_FLASH_TOOL option:>
      --- ecos.ecc.orig       Fri Jan 28 11:21:43 2000
      +++ ecos.ecc            Fri Jan 28 11:22:01 2000
      @@ -150,7 +150,7 @@
       cdl_option CYGBLD_BUILD_FLASH_TOOL {
      	   # Flavor: bool
      	   # No user value, uncomment the following line to provide one.
      -    # user_value 0
      +    user_value 1
      	   # value_source default
      	   # Default value: 0
      	   # Requires:  CYG_HAL_STARTUP == "RAM" 
 % ecosconfig resolve
 % ecosconfig tree
 % make

The flash tool is installed in ./install/bin

Prepare board for CygMon
~~~~~~~~~~~~~~~~~~~~~~~~
 1. Set jumper 7-8 on LK6   [using the Angle code in the 16 bit EPROM]
 2. Set jumper 5-6 on LK6   [select 8bit ROM mode]
 3. Set jumper LK18         [ROM remap - this is also required for eCos]
 4. Set S1 to 0-0-1-1       [20MHz operation]


Program FLASH
~~~~~~~~~~~~~
 1. Download the CygMon relocated image onto the PID board:
      % cd /tmp
      % arm-elf-gdb -nw cygmon/install/bin/cygmon.img

  	(gdb) target rdi s=<serial device>
 	Angel Debug Monitor V1.04 (Advanced RISC Machines SDT 2.11a) for PID
 	Built with Serial(x1), Parallel, DCC
 	Rebuilt on Apr  7 1998 at 22:20:43
 	Serial Rate:   9600
 	Connected to ARM RDI target.
  	(gdb) load
 	Loading section .rom_vectors, size 0x60 lma 0x60000
 	Loading section .text, size 0xeea8 lma 0x60060
 	Loading section .rodata, size 0x304c lma 0x6ef08
 	Loading section .data, size 0x7f8 lma 0x71f54
 	Start address 0x60060 , load size 75596
 	Transfer rate: 5548 bits/sec.
  	(gdb) quit

   This will download the stubs onto the board at 0x60000..0x80000

   Use /dev/ttyS0, COM1 or similar for the <serial device> name.

 2. Now download the FLASH programmer tool
      % arm-elf-gdb -nw pid-flash/install/bin/prog_flash.img

 	(gdb) target rdi s=<serial device>
 	Angel Debug Monitor V1.04 (Advanced RISC Machines SDT 2.11a) for PID
 	Built with Serial(x1), Parallel, DCC
 	Rebuilt on Apr  7 1998 at 22:20:43
 	Serial Rate:   9600
 	Connected to ARM RDI target.
 	(gdb) load
 	Loading section .rom_vectors, size 0x60 lma 0x4000
 	Loading section .text, size 0x4964 lma 0x4060
 	Loading section .rodata, size 0x384 lma 0x89c4
 	Loading section .data, size 0x28c lma 0x8d48
 	Start address 0x4060 , load size 20436
 	Transfer rate: 5449 bits/sec.
 	(gdb) cont

 3. The FLASH tool will output some text on the board serial port B at
    38400 baud:

       ARM eCos
       FLASH here!
       manuf: 8, device: 40
       Error: Wrong Manufaturer: 08
       ... Please change FLASH jumper

 4. This text is repeated until you remove the jumper 7-8 on LK6. Then
    the output should be:

       manuf: 1F, device: A4
       AT29C040A recognised
       About to program FLASH using data at 60000..80000
       *** Press RESET now to abort!
    
 5. You have about 10 seconds to abort the operation by pressing
    reset. After this timeout, the FLASH programming happens:
  
      ...Programming FLASH
      All done!

 6. Quit/kill the GDB process which will hang.

 7. Next time you reset the board, CygMon will be in control, communicating
    on serial port A at 38400 baud. See documentation for further details
    on how to connect with GDB.