f06x_oscillator_cmos.c

C8051F060的时钟配置例子

//-----------------------------------------------------------------------------
// F06x_Oscillator_CMOS.c
//-----------------------------------------------------------------------------
// Copyright 2006 Silicon Laboratories, Inc.
// http://www.silabs.com
//
// Program Description:
//
// This example demonstrates how to initialize for and switch to an external
// CMOS Oscillator.
// - Pinout:
//    P0.0 -> /SYSCLK
//
//    P1.6 -> LED
//
//    all other port pins unused
//
//    XTAL1 -> XTAL1 - External CMOS Oscillator input
//
//
// How To Test:
//
// 1) Define the input CMOS clock frequency using <CMOS_clock>
// 2) Compile and download code to a 'F06x device.
// 3) Connect the CMOS input clock to XTAL1 (J21 on the TB)
// 4) Run the code:
//      - the test will blink an LED at a frequency based on the CMOS
//         Oscillator
//      - the 'F06x will also output the SYSCLK to a port pin (P0.0) for
//         observation
//
//
// FID:            06X000010
// Target:         C8051F06x
// Tool chain:     Keil C51 7.50 / Keil EVAL C51
// Command Line:   None
//
// Release 1.0
//    -Initial Revision (TP)
//    -31 MAY 2006
//

//-----------------------------------------------------------------------------
// Includes
//-----------------------------------------------------------------------------

#include <C8051F060.h>                 // SFR declarations

//-----------------------------------------------------------------------------
// Global CONSTANTS
//-----------------------------------------------------------------------------

#define CMOS_clock 3062500             // CMOS oscillator frequency

// Timer2 using SYSCLK/12 as its time base
// Timer2 counts 65536 SYSCLKs per Timer2 interrupt
// LED target flash rate = 10 Hz (may be slower, depending on CMOS_clock)
//
// If CMOS_clock is too slow to divide into a number of counts,
// <count> will always remain 0. In this case, the LED Flash rate will be
// slower than 10 Hz.
#define LED_interrupt_count CMOS_clock/12/65536/10


sfr16 RCAP2 = 0xCA;                    // Timer2 reload value
sfr16 TMR2 = 0xCC;                     // Timer2 counter

sbit LED = P1^6;                       // LED='1' means ON

//-----------------------------------------------------------------------------
// Function PROTOTYPES
//-----------------------------------------------------------------------------

void SYSCLK_Init (void);
void ExtCMOSOsc_Init (void);
void Port_Init (void);
void Timer2_Init (void);

void Timer2_ISR (void);

//-----------------------------------------------------------------------------
// MAIN Routine
//-----------------------------------------------------------------------------
//
// Main routine performs all configuration tasks, switches to the external CMOS
// oscillator, and loops forever, blinking the LED.
//
void main (void) {

   WDTCN = 0xDE;                       // disable watchdog timer
   WDTCN = 0xAD;

   SFRPAGE = CONFIG_PAGE;

   SYSCLK_Init ();                     // Initialize system clock to 24.5MHz

   ExtCMOSOsc_Init ();                 // Initialize for and switch to the
                                       // external CMOS oscillator

   Port_Init ();                       // Initialize crossbar and GPIO

   SFRPAGE = TMR2_PAGE;

   Timer2_Init ();                     // Init Timer2 to generate
                                       // interrupts for the LED.

   EA = 1;                             // Enable global interrupts

   SFRPAGE = LEGACY_PAGE;              // Sit in this SFRPAGE

   while (1) {                         // Spin forever
   }
}

//-----------------------------------------------------------------------------
// Initialization Routines
//-----------------------------------------------------------------------------

//-----------------------------------------------------------------------------
// SYSCLK_Init ()
//-----------------------------------------------------------------------------
//
// Return Value : None
// Parameters   : None
//
// This routine initializes the system clock to use the internal 24.5 MHz
// oscillator as its clock source.  Also enables missing clock detector reset.
//
void SYSCLK_Init (void)
{
   OSCICN = 0x83;                      // Configure internal oscillator for
                                       // its highest frequency (24.5 MHz)

   RSTSRC = 0x04;                      // Enable missing clock detector
}

//-----------------------------------------------------------------------------
// ExtCMOSOsc_Init ()
//-----------------------------------------------------------------------------
//
// Return Value : None
// Parameters   : None
//
// This routine initializes for and switches to the External CMOS Oscillator.
//
// Note: In CMOS clock configuration, the clock source should be wired to the
// XTAL1 pin as shown in Option 4 in the Oscillators section of the datasheet.
//
void ExtCMOSOsc_Init (void)
{
   OSCXCN = 0x20;                      // External Oscillator is a CMOS clock
                                       // (no divide by 2 stage)
                                       // XFCN bit settings do not apply to a
                                       // CMOS clock

   CLKSEL = 0x01;                      // Switch to the external CMOS clock
}

//-----------------------------------------------------------------------------
// Port_Init ()
//-----------------------------------------------------------------------------
//
// Return Value : None
// Parameters   : None
//
// Configure the Crossbar and GPIO ports.
//
// P0.0   digital   push-pull     /SYSCLK
// P0.1                           unused
// P0.2                           unused
// P0.3                           unused
// P0.4                           unused
// P0.5                           unused
// P0.6                           unused
// P0.7                           unused
//
// P1.0                           unused
// P1.1                           unused
// P1.2                           unused
// P1.3                           unused
// P1.4                           unused
// P1.5                           unused
// P1.6   digital   push-pull     LED
// P1.7                           unused
//
// P2                             unused
//
// P3                             unused
//
// P4                             unused
//
// P5                             unused
//
// P6                             unused
//
// P7                             unused
//
void PORT_Init (void)
{
   P0MDOUT |= 0x01;                    // Enable /SYSCLK as a push-pull output

   P1MDOUT |= 0x40;                    // Enable LED as a push-pull output

   XBR1 = 0x80;                        // Route /SYSCLK to a port pin
   XBR2 = 0x40;                        // Enable crossbar and weak pull-ups
}

//-----------------------------------------------------------------------------
// Timer2_Init ()
//-----------------------------------------------------------------------------
//
// Return Value : None
// Parameters   : None
//
// Configure Timer2 to 16-bit auto-reload and generate an interrupt after the
// maximum possible time (TMR2RL = 0x0000).
//
void Timer2_Init (void)
{
   TMR2CN = 0x00;                      // Stop Timer2; Clear TF2;
                                       // auto-reload mode

   TMR2CF = 0x00;                      // use SYSCLK/12 as timebase; count up

   RCAP2 = 0x0000;                     // Init reload value
   TMR2 = 0xffff;                      // Set to reload immediately

   ET2 = 1;                            // Enable Timer2 interrupts

   TR2 = 1;                            // Start Timer2
}

//-----------------------------------------------------------------------------
// Interrupt Service Routines
//-----------------------------------------------------------------------------

//-----------------------------------------------------------------------------
// Timer2_ISR
//-----------------------------------------------------------------------------
//
// This routine changes the state of the LED whenever Timer2 overflows.
//
void Timer2_ISR (void) interrupt 5
{
   static unsigned int count = 0;

   TF2 = 0;                            // Clear Timer2 interrupt flag

   if (count == LED_interrupt_count)
   {
      LED = ~LED;                      // Change state of LED

      count = 0;
   }
   else
   {
      count++;
   }
}

//-----------------------------------------------------------------------------
// End Of File
//-----------------------------------------------------------------------------