usbd_sensedata.h

凌阳SPCE3200 系统开发板随机自带源程序。共安排了32个子目录

// SUNPLUS  S+core IDE generated include file.
#ifndef ANISPG290_USBD_SENSEDATA_H_27644_25547__INCLUDED_
#define ANISPG290_USBD_SENSEDATA_H_27644_25547__INCLUDED_

extern unsigned char R_SCSIVendorInformation[8];
extern unsigned char R_SCSIPID_Disk0[16];
extern unsigned char R_SCSIPID_Disk1[16];
extern unsigned char R_SCSIProductRevisionLevel[4];


unsigned char R_USBD_SenseData[39][3]=
{
	{0x00, 0x00, 0x00},		//0x00 - NO SENSE
	{0x01, 0x17, 0x01},		//0x01 - RECOVERD DATA WITH RETRIES
	{0x01, 0x18, 0x00},		//0x02 - RECOVERD DATA WITH ECC
	{0x02, 0x04, 0x01},		//0x03 - LOGICAL DRIVE NOT READY - BECOMING READY
	{0x02, 0x04, 0x02},		//0x04 - LOGICAL DRIVE NOT READY - INITIALIZATION REQUIRED
	{0x02, 0x04, 0x04},		//0x05 - LOGICAL UNIT NOT READY - FORMAT IN PROGRESS
	{0x02, 0x04, 0xFF},		//0x06 - LOGICAL DRIVE NOT READY - DEVICE IS BUSY
	{0x02, 0x06, 0x00},		//0x07 - NO REFERENCE POSITION FOUND
	{0x02, 0x08, 0x00},		//0x08 - LOGICAL UNIT COMMUNICATION FAILURE
	{0x02, 0x08, 0x01},		//0x09 - LOGICAL UNIT COMMUNICATION TIME-OUT
	{0x02, 0x08, 0x80},		//0x0A - LOGICAL UNIT COMMUNICATION OVERRUN
	{0x02, 0x3A, 0x00},		//0x0B - MEDIUM NOT PRESENT
	{0x02, 0x54, 0x00},		//0x0C - USB TO HOST SYSTEM INTERFACE FAILURE
	{0x02, 0x80, 0x00},		//0x0D - INSUFFICIENT RESOURCES
	{0x02, 0xFF, 0xFF},		//0x0E - UNKNOWN ERROR
	{0x03, 0x02, 0x00},		//0x0F - NO SEEK COMPLETE
	{0x03, 0x03, 0x00},		//0x10 - WRITE FAULT
	{0x03, 0x10, 0x00},		//0x11 - ID CRC ERROR
	{0x03, 0x11, 0x00},		//0x12 - UNRECOVERD READ ERROR
	{0x03, 0x12, 0x00},		//0x13 - ADDRESS MARK NOT FOUND FOR ID FIELD
	{0x03, 0x13, 0x00},		//0x14 - ADDRESS MARK NOT FOUND FOR DATA FIELD
	{0x03, 0x14, 0x00},		//0x15 - RECORDED ENTITY NOT FOUND
	{0x03, 0x30, 0x01},		//0x16 - CANNOT READ MEDIUM - UNKNOWN FORMAT
	{0x03, 0x31, 0x01},		//0x17 - FORMAT COMMAND FAILED
	{0x04, 0x40, 0x80},		//0x18 - DIAGNOSTIC FAILURE ON COMPONENT NN (80H-FFH)
	{0x05, 0x1A, 0x00},		//0x19 - PARAMETER LIST LENGTH ERROR
	{0x05, 0x20, 0x00},		//0x1A - INVALID COMMAND OPERATION CODE
	{0x05, 0x21, 0x00},		//0x1B - LOGICAL BLOCK ADDRESS OUT OF RANGE
	{0x05, 0x24, 0x00},		//0x1C - INVALID FIELD IN COMMAND PACKET   
	{0x05, 0x25, 0x00},		//0x1D - LOGICAL UNIT NOT SUPPORTED
	{0x05, 0x26, 0x00},		//0x1E - INVALID FIELD IN PARAMETER LIST
	{0x05, 0x26, 0x01},		//0x1F - PARAMETER NOT SUPPORTED 
	{0x05, 0x26, 0x02},		//0x20 - PARAMETER VALUE INVALID
	{0x05, 0x39, 0x00},		//0x21 - SAVING PARAMETERS NOT SUPPORT  
	{0x06, 0x28, 0x00},		//0x22 - NOT READY TO READY TRANSITION - MEDIA CHANGED
	{0x06, 0x29, 0x00},		//0x23 - POWER ON RESET OR BUS DEVICE RESET OCCURRED
	{0x06, 0x2F, 0x00},		//0x24 - COMMANDS CLEARED BY ANOTHER INITIATOR
	{0x07, 0x27, 0x00},		//0x25 - WRITE PROTECTED MEDIA
	{0x0B, 0x4E, 0x00}		//0x26 - OVERLAPPED COMMAND ATTEMPED			
};

#endif //ANISPG290_USBD_SENSEDATA_H_27644_25547__INCLUDED_