yy.h

kf902 104 uart- 19200

//////////////////////////////////////////////////////////////////
#define	    COMM_MODULE_LOGIN_ON		0X00    //登记
					 
#define 	COMM_SET_MCU_IDLE			0X04	//设置模块空闲睡眠模式			
#define 	COMM_CONTROL_ANTENNA		0X05	//模块天线控制、自动寻卡设置
			
#define 	COMM_PA_OUT_SET				0X06	//PA口输出置位			
#define 	COMM_PB_OUT_SET				0X07	//PB口输出置位			
#define 	COMM_PA_OUT_CLR				0X08	//PA口输出清0			
#define 	COMM_PB_OUT_CLR				0X09	//PB口输出清0
#define 	COMM_PA_DRAIN_OPEN			0X0A	//PA口漏极开路设置
#define 	COMM_PB_DRAIN_OPEN			0X0B	//PB口漏极开路设置
#define 	COMM_PA_INPUT				0X0C	//PA口输入			
#define 	COMM_PB_INPUT				0X0D	//PB口输入			
#define 	COMM_RS485_MODE				0X0E	//RS485工作模式
#define 	COMM_INSIDE_CARD_CODE		0X0F	//内部1000个卡号启动设置
#define 	COMM_WRITE_CARD_INTO		0X10	//写入卡号到模块内
#define 	COMM_READ_CARD_OUT			0X11	//读出卡号到模块内

#define 	COMM_WRITE_MODULE_ID		0X13	//设置设备标识
#define 	COMM_READ_MODULE_ID			0X14	//读取设备标识
#define 	COMM_SET_COM_BPS			0X15	//串口波特率设置
#define 	COMM_READ_HARDWARE_VERSION	0X16	//读取产品硬件版本
#define 	COMM_READ_SEARIAL_NUMBER	0X17	//读取产品序列号
#define 	COMM_WRITE_SEARIAL_NUMBER	0X18	//设置产品序列号

#define 	COMM_SELF_SEARCH_CARD		0X19	//主动寻卡
#define 	COMM_CONTROL_RED_LED		0X1A	//控制红灯
#define 	COMM_CONTROL_GREEN_LED		0X1B	//控制绿灯
#define 	COMM_CONTROL_YELLOW_LED		0X1C	//控制黄灯
#define 	COMM_CONTROL_BUZZER			0X1D	//控制蜂鸣器
#define 	COMM_CONTROL_CLR_KEY		0X1E	//清除键值
#define 	COMM_CONTROL_DAT_DISPLAY	0X1F	//发显示数据到显示终端
								   

#define 	COMM_MIFARE_SEARCH_CARD		0X20	//TYPE-A寻卡	
#define 	COMM_READ_BLOCK				0X21	//读块	
#define 	COMM_READ_SECTOR			0X22	//读扇区
#define 	COMM_WRITE_BLOCK			0X23	//写块	
#define 	COMM_INIT_PURSE				0X24	//初始化钱包
#define 	COMM_READ_PURSE				0X25	//读钱包	
#define 	COMM_INC_VALUE				0X26	//充值	
#define 	COMM_DEC_VALUE				0X27	//扣款	
#define 	COMM_BAK_PURSE				0X28	//备份钱包值
#define 	COMM_CARD_HALT				0X29	//卡休眠
#define 	COMM_LOAD_KEY_AB			0X2A	//下载密钥
#define 	COMM_READ_EEPROM			0X2B	//读RC500EEPROM
#define 	COMM_WRITE_EEPROM			0X2C	//写RC500EEPROM

#define 	COMM_HALT_ULTRA_LIGHT		0X32	//Halt Ultra Light卡				
#define 	COMM_SEL_ULTRA_LIGHT		0X33	//选定一张Ultra Light卡	
#define 	COMM_READ_ULTRA_LIGHT		0X34	//Ultra Light读卡	
#define 	COMM_WRITE_ULTRA_LIGHT		0X35	//Ultra Light写卡 
#define 	COMM_SET_SAM_BPS			0X36	//设置SAM卡波特率	
#define 	COMM_RET_SAM				0X37	//SAM 卡复位1 字节波特率代码，0：9600；1：38400

#define 	COMM_SAM_COS				0X38	//SAM 卡COS 命令
#define 	COMM_SAM_CONFIGE			0X39	//SAM 卡硬件配置		
		
#define 	COMM_SET_TYPE_AB_OTHER		0X3A	//设定读卡模式TYPE A/B

#define 	COMM_SEARCH_AT88RF020		0X3E	//寻卡88RF020	
#define 	COMM_CHECK_AT88RF020_KEY	0X3F	//验证88RF020密钥	
#define 	COMM_READ_AT88RF020_BLOCK	0X40	//88RF020读块
#define 	COMM_WRITE_AT88RF020_BLOCK	0X41	//88RF020写块
#define 	COMM_AT88RF020_LOCK			0X42	//88RF020锁定
#define 	COMM_AT88RF020_COUNT		0X43	//88RF020计数
#define 	COMM_AT88RF020_HALT			0X44	//88RF020卡休眠	
#define 	COMM_MIFARE1_CONFIG_RESTORE	0X45	//mifare one 恢复出厂	

#define 	COMM_MIFARE1_PCD_REQUEST	0X46	//mifare one 寻卡
#define 	COMM_MIFARE1_PCD_ANTICOLL	0X47	//mifare one 防冲撞
#define 	COMM_MIFARE1_PCD_SELECT		0X48	//mifare one 选卡
#define 	COMM_AUTHENTICATION1		0X49	//认证1
#define 	COMM_AUTHENTICATION2		0X4A	//认证2
#define 	COMM_PCD_READ_BLOCK			0X4B	//无密码读块
#define 	COMM_PCD_WRITE_BLOCK		0X4C	//无密码写块
#define 	COMM_PCD_INIT_PURSE			0X4D	//无密码初始化钱包
#define 	COMM_PCD_READ_PURSE			0X4E	//无密码读钱包
#define 	COMM_PCD_DEC_VALUE			0X4F	//无密码减值
#define 	COMM_PCD_INC_VALUE			0X50	//无密码充值
#define 	COMM_PCD_RESTORE			0X51	//无密码将钱包值调入缓冲区
#define 	COMM_PCD_TRANSFER			0X52	//无密码保存缓冲区的值
#define 	COMM_PCD_TYPEA_HIGH_RST		0X53	//TYPEA CPU复位命令
#define 	COMM_PCD_TYPEA_HIGH_COS		0X54	//TYPEA CPU的COS命令
#define 	COMM_PCD_TYPEB_ATTRIB		0X55	//激活TYPE卡
#define 	COMM_RET_TYPE_B_CPU			0X3B	//TYPE-BCPU 卡复位
#define 	COMM_TYPE_B_CPU_COS			0X3C	//TYPE-B  COS 命令
#define 	COMM_TYPE_B_CPU_HALT		0X3D	//TYPE-B卡休眠

#define 	COMM_TYPE_B_ST_SELECT		0X60			//锁定一张ST卡
#define 	COMM_TYPE_B_ST_COMPLETION	0X61			//命令ST卡进入DESACTIVED状态
#define 	COMM_TYPE_B_READ_SR176		0X62			//读SR176卡1块数据
#define 	COMM_TYPE_B_WRITE_SR176		0X63			//写SR176卡1块数据
#define 	COMM_TYPE_B_PROTECT_SR176	0X64			//SR176卡块锁定 
#define 	COMM_TYPE_B_READ_SRIX4K		0X65			//读SRIX4K卡1块数据
#define 	COMM_TYPE_B_WRITE_SRIX4K	0X66			//写SRIX4K卡1块数据
#define 	COMM_TYPE_B_AUATHENTICATE_SRIX4K	0X67	//SRIX4K卡鉴别操作
#define 	COMM_TYPE_B_GET_UID_SRIX4K			0X68			//获取SRIX4K卡UID
#define 	COMM_TYPE_B_LOCK_SRIX4K				0X69			//SRIX4K卡块锁定 

#define 	COMM_CARD_LIGHT						0X6A 
#define 	COMM_CARD_CL_DESELECT				0X6B

#define 	COMM_ISO15693_Inventory				0X70			//
#define 	COMM_ISO15693_Stay_Quiet			0X71			//
#define 	COMM_ISO15693_Select				0X72			//
#define 	COMM_ISO15693_Reset_Ready			0X73			//
#define 	COMM_ISO15693_Read					0X74			//
#define 	COMM_ISO15693_Write					0X75			//
#define 	COMM_ISO15693_Lock_Block			0X76			//
#define 	COMM_ISO15693_Write_AFI				0X77			//
#define 	COMM_ISO15693_Lock_AFI				0X78			//
#define 	COMM_ISO15693_Write_DSFID			0X79			//
#define 	COMM_ISO15693_Lock_DSFID			0X7A			//
#define 	COMM_ISO15693_Get_System_Info		0X7B			//
#define 	COMM_ISO15693_Get_Block_Security	0X7C			//


#define 	COMM_125K_SEARCH_CARD	 			0x80
#define 	COMM_SET_3686KHZ			0XF1	//设置频率输出
#define 	COMM_PROGRAME_ISP			0xf2	//isp	
#define 	COMM_PRODUCT_NAME			0xf3	//产品名字