scarakins.c

CNC 的开放码,EMC2 V2.2.8版

/*****************************************************************
* Description: scarakins.c
*   Kinematics for scara typed robots
*   Set the params using HAL to fit your robot
*
*   Derived from a work by Sagar Behere
*
* Author: Sagar Behere 
* License: GPL Version 2
* System: Linux
*
* Copyright (c) 2003 All rights reserved.
*
* Last change:
* $Revision: 1.5 $
* $Author: jepler $
* $Date: 2007/02/10 04:13:54 $
*******************************************************************
*/

#include "posemath.h"
#include "rtapi_math.h"
#include "kinematics.h"             /* decls for kinematicsForward, etc. */

#ifdef RTAPI
#include "rtapi.h"		/* RTAPI realtime OS API */
#include "rtapi_app.h"		/* RTAPI realtime module decls */
#include "hal.h"

struct scara_data {
    hal_float_t d1, d2, d3, d4, d5, d6;
} *haldata = 0;

/* key dimensions

   joint[0] = Entire arm rotates around a vertical axis at its inner end
		which is attached to the earth.  A value of zero means the
		inner arm is pointing along the X axis.
   D1 = Vertical distance from the ground plane to the center of the inner
		arm.
   D2 = Horizontal distance between joint[0] axis and joint[1] axis, ie.
		the length of the inner arm.
   joint[1] = Outer arm rotates around a vertical axis at its inner end
		which is attached to the outer end of the inner arm.  A
		value of zero means the outer arm is parallel to the
		inner arm (and extending outward).
   D3 = Vertical distance from the center of the inner arm to the center
		of the outer arm.  May be positive or negative depending
		on the structure of the robot.
   joint[2] = End effector slides along a vertical axis at the outer end
		of the outer arm.  A value of zero means the end effector
		is at the same height as the center of the outer arm, and
		positive values mean downward movement.
   D4 = Horizontal distance between joint[1] axis and joint[2] axis, ie.
		the length of the outer arm
   joint[3] = End effector rotates around the same vertical axis that it
		slides along.  A value of zero means that the tooltip (if
		offset from the axis) is pointing in the same direction
		as the centerline of the outer arm.
   D5 = Vertical distance from the end effector to the tooltip.  Positive
		means the tooltip is lower than the end effector, and is
		the normal case.
   D6 = Horizontal distance from the centerline of the end effector (and
		the joints 2 and 3 axis) and the tooltip.  Zero means the
		tooltip is on the centerline.  Non-zero values should be
		positive, if negative they introduce a 180 degree offset
		on the value of joint[3].
*/

#define D1 (haldata->d1)
#define D2 (haldata->d2)
#define D3 (haldata->d3)
#define D4 (haldata->d4)
#define D5 (haldata->d5)
#define D6 (haldata->d6)

/* joint[0], joint[1] and joint[3] are in degrees and joint[2] is in length units */
int kinematicsForward(const double * joint,
                      EmcPose * world,
                      const KINEMATICS_FORWARD_FLAGS * fflags,
                      KINEMATICS_INVERSE_FLAGS * iflags)
{
    double a0, a1, a3;
    double x, y, z, c;

/* convert joint angles to radians for sin() and cos() */

    a0 = joint[0] * ( PM_PI / 180 );
    a1 = joint[1] * ( PM_PI / 180 );
    a3 = joint[3] * ( PM_PI / 180 );
/* convert angles into world coords */

    a1 = a1 + a0;
    a3 = a3 + a1;

    x = D2*cos(a0) + D4*cos(a1) + D6*cos(a3);
    y = D2*sin(a0) + D4*sin(a1) + D6*sin(a3);
    z = D1 + D3 - joint[2] - D5;
    c = a3;
	
    *iflags = 0;
    if (joint[1] < 90)
	*iflags = 1;
	
    world->tran.x = x;
    world->tran.y = y;
    world->tran.z = z;
    world->c = c * 180 / PM_PI;
	
    world->a = joint[4];
    world->b = joint[5];
	
    return (0);
}

int kinematicsInverse(const EmcPose * world,
                      double * joint,
                      const KINEMATICS_INVERSE_FLAGS * iflags,
                      KINEMATICS_FORWARD_FLAGS * fflags)
{
    double a3;
    double q0, q1;
    double xt, yt, rsq, cc;
    double x, y, z, c;

    x = world->tran.x;
    y = world->tran.y;
    z = world->tran.z;
    c = world->c;

    /* convert degrees to radians */
    a3 = c * ( PM_PI / 180 );

    /* center of end effector (correct for D6) */
    xt = x - D6*cos(a3);
    yt = y - D6*sin(a3);

    /* horizontal distance (squared) from end effector centerline
	to main column centerline */
    rsq = xt*xt + yt*yt;
    /* joint 1 angle needed to make arm length match sqrt(rsq) */
    cc = (rsq - D2*D2 - D4*D4) / (2*D2*D4);
    if(cc < -1) cc = -1;
    if(cc > 1) cc = 1;
    q1 = acos(cc);

    if (*iflags)
	q1 = -q1;

    /* angle to end effector */
    q0 = atan2(yt, xt);

    /* end effector coords in inner arm coord system */
    xt = D2 + D4*cos(q1);
    yt = D4*sin(q1);

    /* inner arm angle */
    q0 = q0 - atan2(yt, xt);

    /* q0 and q1 are still in radians. convert them to degrees */
    q0 = q0 * (180 / PM_PI);
    q1 = q1 * (180 / PM_PI);

    joint[0] = q0;
    joint[1] = q1;
    joint[2] = D1 + D3 - D5 - z;
    joint[3] = c - ( q0 + q1);
    joint[4] = world->a;
    joint[5] = world->b;

    *fflags = 0;

    return (0);
}

int kinematicsHome(EmcPose * world,
                   double * joint,
                   KINEMATICS_FORWARD_FLAGS * fflags,
                   KINEMATICS_INVERSE_FLAGS * iflags)
{
  /* use joints, set world */
  return kinematicsForward(joint, world, fflags, iflags);
}

KINEMATICS_TYPE kinematicsType()
{
  return KINEMATICS_BOTH;
}

#define DEFAULT_D1 490
#define DEFAULT_D2 340
#define DEFAULT_D3  50
#define DEFAULT_D4 250
#define DEFAULT_D5  50
#define DEFAULT_D6  50

EXPORT_SYMBOL(kinematicsType);
EXPORT_SYMBOL(kinematicsForward);
EXPORT_SYMBOL(kinematicsInverse);
EXPORT_SYMBOL(kinematicsHome);

int comp_id;

int rtapi_app_main(void) {
    int res=0;
    
    comp_id = hal_init("scarakins");
    if (comp_id < 0) return comp_id;
    
    haldata = hal_malloc(sizeof(*haldata));
    if (!haldata) goto error;
    D1 = DEFAULT_D1;
    D2 = DEFAULT_D2;
    D3 = DEFAULT_D3;
    D4 = DEFAULT_D4;
    D5 = DEFAULT_D5;
    D6 = DEFAULT_D6;

    if((res = hal_param_float_new("scarakins.D1", HAL_RW, &haldata->d1, comp_id)) != HAL_SUCCESS) goto error;
    if((res = hal_param_float_new("scarakins.D2", HAL_RW, &haldata->d2, comp_id)) != HAL_SUCCESS) goto error;
    if((res = hal_param_float_new("scarakins.D3", HAL_RW, &haldata->d3, comp_id)) != HAL_SUCCESS) goto error;
    if((res = hal_param_float_new("scarakins.D4", HAL_RW, &haldata->d4, comp_id)) != HAL_SUCCESS) goto error;
    if((res = hal_param_float_new("scarakins.D5", HAL_RW, &haldata->d5, comp_id)) != HAL_SUCCESS) goto error;
    if((res = hal_param_float_new("scarakins.D6", HAL_RW, &haldata->d6, comp_id)) != HAL_SUCCESS) goto error;
    
    hal_ready(comp_id);
    return 0;
    
error:
    hal_exit(comp_id);
    return res;
}

void rtapi_app_exit(void) { hal_exit(comp_id); }
#endif