xstatus.h

自学ZedBoard：使用IP通过ARM PS访问FPGA（源代码）

#define XST_EMAC_OUT_OF_BUFFERS     1005L	/* Driver is out of buffers */
#define XST_EMAC_PARSE_ERROR        1006L	/* Invalid driver init string */
#define XST_EMAC_COLLISION_ERROR    1007L	/* Excess deferral or late
						 * collision on polled send */

/*********************** UART statuses 1051 - 1075 ***************************/
#define XST_UART

#define XST_UART_INIT_ERROR         1051L
#define XST_UART_START_ERROR        1052L
#define XST_UART_CONFIG_ERROR       1053L
#define XST_UART_TEST_FAIL          1054L
#define XST_UART_BAUD_ERROR         1055L
#define XST_UART_BAUD_RANGE         1056L


/************************ IIC statuses 1076 - 1100 ***************************/

#define XST_IIC_SELFTEST_FAILED         1076	/* self test failed            */
#define XST_IIC_BUS_BUSY                1077	/* bus found busy              */
#define XST_IIC_GENERAL_CALL_ADDRESS    1078	/* mastersend attempted with   */
					     /* general call address        */
#define XST_IIC_STAND_REG_RESET_ERROR   1079	/* A non parameterizable reg   */
					     /* value after reset not valid */
#define XST_IIC_TX_FIFO_REG_RESET_ERROR 1080	/* Tx fifo included in design  */
					     /* value after reset not valid */
#define XST_IIC_RX_FIFO_REG_RESET_ERROR 1081	/* Rx fifo included in design  */
					     /* value after reset not valid */
#define XST_IIC_TBA_REG_RESET_ERROR     1082	/* 10 bit addr incl in design  */
					     /* value after reset not valid */
#define XST_IIC_CR_READBACK_ERROR       1083	/* Read of the control register */
					     /* didn't return value written */
#define XST_IIC_DTR_READBACK_ERROR      1084	/* Read of the data Tx reg     */
					     /* didn't return value written */
#define XST_IIC_DRR_READBACK_ERROR      1085	/* Read of the data Receive reg */
					     /* didn't return value written */
#define XST_IIC_ADR_READBACK_ERROR      1086	/* Read of the data Tx reg     */
					     /* didn't return value written */
#define XST_IIC_TBA_READBACK_ERROR      1087	/* Read of the 10 bit addr reg */
					     /* didn't return written value */
#define XST_IIC_NOT_SLAVE               1088	/* The device isn't a slave    */

/*********************** ATMC statuses 1101 - 1125 ***************************/

#define XST_ATMC_ERROR_COUNT_MAX    1101L	/* the error counters in the ATM
						   controller hit the max value
						   which requires the statistics
						   to be cleared */

/*********************** Flash statuses 1126 - 1150 **************************/

#define XST_FLASH_BUSY                1126L	/* Flash is erasing or programming
						 */
#define XST_FLASH_READY               1127L	/* Flash is ready for commands */
#define XST_FLASH_ERROR               1128L	/* Flash had detected an internal
						   error. Use XFlash_DeviceControl
						   to retrieve device specific codes
						 */
#define XST_FLASH_ERASE_SUSPENDED     1129L	/* Flash is in suspended erase state
						 */
#define XST_FLASH_WRITE_SUSPENDED     1130L	/* Flash is in suspended write state
						 */
#define XST_FLASH_PART_NOT_SUPPORTED  1131L	/* Flash type not supported by
						   driver */
#define XST_FLASH_NOT_SUPPORTED       1132L	/* Operation not supported */
#define XST_FLASH_TOO_MANY_REGIONS    1133L	/* Too many erase regions */
#define XST_FLASH_TIMEOUT_ERROR       1134L	/* Programming or erase operation
						   aborted due to a timeout */
#define XST_FLASH_ADDRESS_ERROR       1135L	/* Accessed flash outside its
						   addressible range */
#define XST_FLASH_ALIGNMENT_ERROR     1136L	/* Write alignment error */
#define XST_FLASH_BLOCKING_CALL_ERROR 1137L	/* Couldn't return immediately from
						   write/erase function with
						   XFL_NON_BLOCKING_WRITE/ERASE
						   option cleared */
#define XST_FLASH_CFI_QUERY_ERROR     1138L	/* Failed to query the device */

/*********************** SPI statuses 1151 - 1175 ****************************/

#define XST_SPI_MODE_FAULT          1151	/* master was selected as slave */
#define XST_SPI_TRANSFER_DONE       1152	/* data transfer is complete */
#define XST_SPI_TRANSMIT_UNDERRUN   1153	/* slave underruns transmit register */
#define XST_SPI_RECEIVE_OVERRUN     1154	/* device overruns receive register */
#define XST_SPI_NO_SLAVE            1155	/* no slave has been selected yet */
#define XST_SPI_TOO_MANY_SLAVES     1156	/* more than one slave is being
						 * selected */
#define XST_SPI_NOT_MASTER          1157	/* operation is valid only as master */
#define XST_SPI_SLAVE_ONLY          1158	/* device is configured as slave-only
						 */
#define XST_SPI_SLAVE_MODE_FAULT    1159	/* slave was selected while disabled */
#define XST_SPI_SLAVE_MODE          1160	/* device has been addressed as slave */
#define XST_SPI_RECEIVE_NOT_EMPTY   1161	/* device received data in slave mode */

#define XST_SPI_COMMAND_ERROR       1162	/* unrecognised command - qspi only */

/********************** OPB Arbiter statuses 1176 - 1200 *********************/

#define XST_OPBARB_INVALID_PRIORITY  1176	/* the priority registers have either
						 * one master assigned to two or more
						 * priorities, or one master not
						 * assigned to any priority
						 */
#define XST_OPBARB_NOT_SUSPENDED     1177	/* an attempt was made to modify the
						 * priority levels without first
						 * suspending the use of priority
						 * levels
						 */
#define XST_OPBARB_PARK_NOT_ENABLED  1178	/* bus parking by id was enabled but
						 * bus parking was not enabled
						 */
#define XST_OPBARB_NOT_FIXED_PRIORITY 1179	/* the arbiter must be in fixed
						 * priority mode to allow the
						 * priorities to be changed
						 */

/************************ Intc statuses 1201 - 1225 **************************/

#define XST_INTC_FAIL_SELFTEST      1201	/* self test failed */
#define XST_INTC_CONNECT_ERROR      1202	/* interrupt already in use */

/********************** TmrCtr statuses 1226 - 1250 **************************/

#define XST_TMRCTR_TIMER_FAILED     1226	/* self test failed */

/********************** WdtTb statuses 1251 - 1275 ***************************/

#define XST_WDTTB_TIMER_FAILED      1251L

/********************** PlbArb statuses 1276 - 1300 **************************/

#define XST_PLBARB_FAIL_SELFTEST    1276L

/********************** Plb2Opb statuses 1301 - 1325 *************************/

#define XST_PLB2OPB_FAIL_SELFTEST   1301L

/********************** Opb2Plb statuses 1326 - 1350 *************************/

#define XST_OPB2PLB_FAIL_SELFTEST   1326L

/********************** SysAce statuses 1351 - 1360 **************************/

#define XST_SYSACE_NO_LOCK          1351L	/* No MPU lock has been granted */

/********************** PCI Bridge statuses 1361 - 1375 **********************/

#define XST_PCI_INVALID_ADDRESS     1361L

/********************** FlexRay constants 1400 - 1409 *************************/

#define XST_FR_TX_ERROR			1400
#define XST_FR_TX_BUSY			1401
#define XST_FR_BUF_LOCKED		1402
#define XST_FR_NO_BUF			1403

/****************** USB constants 1410 - 1420  *******************************/

#define XST_USB_ALREADY_CONFIGURED	1410
#define XST_USB_BUF_ALIGN_ERROR		1411
#define XST_USB_NO_DESC_AVAILABLE	1412
#define XST_USB_BUF_TOO_BIG		1413
#define XST_USB_NO_BUF			1414

/****************** HWICAP constants 1421 - 1429  *****************************/

#define XST_HWICAP_WRITE_DONE		1421


/****************** AXI VDMA constants 1430 - 1440  *****************************/

#define XST_VDMA_MISMATCH_ERROR		1430

/*********************** NAND Flash statuses 1441 - 1459  *********************/

#define XST_NAND_BUSY			1441L	/* Flash is erasing or
						 * programming
						 */
#define XST_NAND_READY			1442L	/* Flash is ready for commands
						 */
#define XST_NAND_ERROR			1443L	/* Flash had detected an
						 * internal error.
						 */
#define XST_NAND_PART_NOT_SUPPORTED	1444L	/* Flash type not supported by
						 * driver
						 */
#define XST_NAND_OPT_NOT_SUPPORTED	1445L	/* Operation not supported
						 */
#define XST_NAND_TIMEOUT_ERROR		1446L	/* Programming or erase
						 * operation aborted due to a
						 * timeout
						 */
#define XST_NAND_ADDRESS_ERROR		1447L	/* Accessed flash outside its
						 * addressible range
						 */
#define XST_NAND_ALIGNMENT_ERROR	1448L	/* Write alignment error
						 */
#define XST_NAND_PARAM_PAGE_ERROR	1449L	/* Failed to read parameter
						 * page of the device
						 */
#define XST_NAND_CACHE_ERROR		1450L	/* Flash page buffer error
						 */

#define XST_NAND_WRITE_PROTECTED	1451L	/* Flash is write protected
						 */

/**************************** Type Definitions *******************************/

typedef int XStatus;

/***************** Macros (Inline Functions) Definitions *********************/


/************************** Function Prototypes ******************************/

#ifdef __cplusplus
}
#endif

#endif /* end of protection macro */