cheetahhlp.htm

Wince BSP 下的Wifi 驱动 基于PXA270 CPU

lists all the access points and peer stations available in the vicinity.</p>
<p>2) A configuration interface that enables you to create and edit SSID 
profiles for your station to associate or join.<br>
</p>
<p><h4>Preferred Networks</h4></p>
<p>You can input a list of SSID profiles as your preferred networks to connect 
in this window. This is done either by <b>Connect</b>ing from existing <b>Active 
SSIDs</b>, or by tapping on the <b>New</b> button to create new ones. Whenever 
the radio is turned on and the last connected network is not available, it will 
start searching for a network to associate automatically in the 
order of your preferred priority.</p>

<p><i><b>Operation Menu:</b></i></p>
<b>New</b> - Create a profile for either an access point or a peer station.<br>
<b>Edit</b> - Modify an existing profile in the Preferred Networks window.<br>
<b>Delete</b> - Delete a profile from the Preferred Networks.<br>
<b>Move Up</b> - Move a profile up to increase the priority for automatic association.<br>
<b>Move Down</b> - Move a profile down to decrease the priority for automatic association.<br>
<p><i><b>Operation Buttons:</b></i></p>
<b>Refresh</b> - Start a new search for all available access points or peer stations in the vicinity.<br>
<b>Connect</b> - Connect to the network you highlighted from either <b>Active Networks</b> or <b>Preferred Networks</b>.<br>

<p>Select on <b>New/Edit</b> from Menu will pop up a New/Edit dialog box for network 
configuration in three tabs: General, Authentication, and Encryption.</p>

<p><h4>Active SSIDs</h4></p>
<p>Active SSIDs window lists all the access points and peer stations available with each record displaying the following fields: </p>
<ul type="circle">
	<li><b>SSID</b> - Network name of an access point or a peer station</li>
	<li><b>Signal</b> - Signal strength in percentage and dBm for that SSID.</li>
	<li><b>WEP</b> - A Lock icon displays if the network needs a security key or network license to access.</li>
	<li><b>Channel</b>- RF channel the network is on.</li>
	<li><b>BSSID (MAC Address)</b> - BSSID or MAC Address of the access point or peer station.</li>
	<li><b>Network Type</b> - AP Icon indicates an access point, green color for b-rate and blue color for g-rate networks. 
	Peer-to-Peer Icon indicates a peer station.</li>
</ul>

<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>

<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->

<a name="profile_gen_dlg"></a><h3>Profile Edit - General</h3>

<p>This is where you configure the general network properties.</p>
<p>
<ul style="margin-top: 0in; margin-bottom: 0in" type="circle">
	<li><b>SSID:</b> Input 
	is required for <b>New. </b>The SSID is populated for <b>Edit</b></li>
	<li><b>Description</b>: Input optional</li>
	<li><b>Network Type</b>: Access Point, Peer-to-Peer</li>
	<li><b>Channel</b>: From 1 to 14 depending on the country code</li>
	<li><b>Connects to</b>: The Internet or Work. Select what your network 
	connects to.</li>
</ul>

<p>Click ok button to confirm, or Cancel button to cancel.</p>
<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>


<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->

<a name="profile_auth_dlg"></a><h3>Profile Edit - Authentication</h3>
<p>This is where you configure the network authentication settings.</p>
<ul style="margin-top: 0in; margin-bottom: 0in" type="circle">
	<li><b>Authentication</b>: Open, Shared, Auto Switch, WPA, WPA-PSK, WPA2, 
	WPA2-PSK</li>
	<li>(Check box)<b> Enable Encryption</b></li>
	<li>(Check Box)<b> Enable network access with 802.1x</b></li>
	<li><b>EAP Type</b>: (<i>Pull-down menu</i>) Smart Card or Certificate 
	(TLS), PEAP</li>
</ul>
<ul>
	<li>
	<b>Property:</b> Click this button to choose the certificate that applies.</li>
</ul>

<p>Click ok button to confirm, or Cancel button to cancel.
<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>

<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->

<a name="profile_encr_dlg"></a><h3>Profile Edit - Encryption</h3>
<p>This is where you configure the encryption settings.</p>
</ul>

<ul style="margin-top: 0in; margin-bottom: 0in" type="circle">
	<li><b>Encryption:</b> 64-bit HEX, 64-bit ASCII, 128-bit HEX and 128-bit ASCII 
	for WEP encryption. TKIP and AES for WPA and WPA-PSK, WPA2 and WPA2-PSK 
	encryption. </li>
	<li><b>Network Key</b>: WEP: 10, 5, 26, 13 characters for 64 and 128 bit 
	encryptions, HEX and ASCII respectively. WPA-PSK/WPA2-PSK: 8-63 characters in key 
	length. </li>
	<li><b>Key Index</b>: 1-4 used for WEP.</li>
</ul>

<p>Click ok button to confirm, or Cancel button to cancel.

<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>

<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->
<a name="ipinfo_tab"></a><h3>IP Information</h3>
<p>Network information is provided in this page.</p>
<ul>
	<li>
	<b>Renew:</b> Click this button to renew the network information.</li>
	<li>
	<b>Ping:</b> Click this button to use the ping utility in the pop-up dialog 
	box.</li>
	<li>
	<b>Trace: </b>Click this button to trace the network routing.</li>
	<li>
	<b>Config:</b> Click this button to configure your network IP Address.</li>
</ul>

<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>
<br>

<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->

<a name="ping_dlg"></a><h3>IP Info - Ping</h3>
<p>This is where you can ping the remote network IP addresses.</p>

<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>
<br>

<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->

<a name="trace_dlg"></a><h3>IP Info - Trace Route</h3>
<p>This is where you can trace the network IP addresses.</p>

<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>
<br>

<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->

<a name="ipconfig_dlg"></a><h3>IP Info - IP Address Config</h3>
<p>This is where you can edit the network IP addresses.</p>
<p>If you select Use server-assigned IP address, nothing you need to configure. 
If you select Use static IP address, you need to input the IP address and Subnet 
mask at minimum.</p>

<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>
<br>


<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->

<a name="advanced_tab"></a><h3>Advanced Settings</h3>

<p><b>Power</b> Management tab allows you to configure <b>Power Save Mode</b></p>
<ul type=circle>
<li><b>Power Save Mode</b></li>
</ul>
<ol>
	<li><b>Auto Enable - </b>Enable the power save mode when internal battery is 
	used; disable the power save mode when external power supply is used. </li>
	<li><b>Always Enable - </b>The power save mode is always enabled.</li>
	<li><b>Always Disable - </b>Disable the power save mode.</li>
</ol>
<ul type="circle">
	<li><b>Performance/Power Sliding Bar </b></li>
</ul>

<p>Move the bar to balance between the performance of the WLAN module and length 
of the battery life. Default is set to Best Performance. Not operable if the Power Save 
Mode is <b>Disable</b>.</p>
<p><b>Available Network Notification - </b>Check Box to enable/disable the 
network notification pop-up.</p>

<ul>
	<li><b>Apply</b> - Tap on this button to apply the changes made for the 
	setting.</li>
</ul>

<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>

<br>
<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->

<a name="cert_enroll_tab"></a><h3>Enroll Certificate</h3>

<p> To connect to a network with a full WPA or WPA2 security, the user is required to enroll the user certificate 
before trying to access to that network. First get the WLAN device connected to the certificate server and then</p>

<ul>
<li> Input the User Name, Password, and Server IP address (obtained from the network admin)</li>
<li> Tap on <b>Enroll</b> button </li>
<li> Check on the pass/fail message in the WEB Enrollment Status window</li>
</ul> 

Enrollment is finished after the "Certificate is enrolled successfully" message
displays in the window. If a failure message displays, check the above three input items or consult with a network admin.

<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>
 
<br>
<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->

<a name="about_tab"></a><h3>Version Information</h3>

<p>This tab provides information about the version number  
for WLAN Driver, Firmware, and 
Configuration Utility and time of the build. Network Card info includes the HW 
Info to indicate the product line (6000, 7000, or 8000 series), and interface (SDIO, CF, 
SPI), as well as the MAC Address of the network card.</p>

<p><b>See Also</b><br><a href="CheetahHlp.htm#main_contents">Main Contents</a> for 
additional topics.</p>
<br>

<P><!-- PegHelp --><hr><!-- ***Topic Break*** -->
</body>
</html>