⭐ 欢迎来到虫虫下载站! | 📦 资源下载 📁 资源专辑 ℹ️ 关于我们
⭐ 虫虫下载站

📄 iwl-hw.h

📁 linux内核源码
💻 H
📖 第 1 页 / 共 2 页
字号:
/****************************************************************************** * * This file is provided under a dual BSD/GPLv2 license.  When using or * redistributing this file, you may do so under either license. * * GPL LICENSE SUMMARY * * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of version 2 of the GNU Geeral Public License as * published by the Free Software Foundation. * * This program is distributed in the hope that it will be useful, but * WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU * General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, * USA * * The full GNU General Public License is included in this distribution * in the file called LICENSE.GPL. * * Contact Information: * James P. Ketrenos <ipw2100-admin@linux.intel.com> * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 * * BSD LICENSE * * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * *  * Redistributions of source code must retain the above copyright *    notice, this list of conditions and the following disclaimer. *  * Redistributions in binary form must reproduce the above copyright *    notice, this list of conditions and the following disclaimer in *    the documentation and/or other materials provided with the *    distribution. *  * Neither the name Intel Corporation nor the names of its *    contributors may be used to endorse or promote products derived *    from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. *****************************************************************************/#ifndef	__iwlwifi_hw_h__#define __iwlwifi_hw_h__/* * This file defines hardware constants common to 3945 and 4965. * * Device-specific constants are defined in iwl-3945-hw.h and iwl-4965-hw.h, * although this file contains a few definitions for which the .c * implementation is the same for 3945 and 4965, except for the value of * a constant. * * uCode API constants are defined in iwl-commands.h. * * NOTE:  DO NOT PUT OS IMPLEMENTATION-SPECIFIC DECLARATIONS HERE * * The iwl-*hw.h (and files they include) files should remain OS/driver * implementation independent, declaring only the hardware interface. *//* uCode queue management definitions */#define IWL_CMD_QUEUE_NUM       4#define IWL_CMD_FIFO_NUM        4#define IWL_BACK_QUEUE_FIRST_ID 7/* Tx rates */#define IWL_CCK_RATES 4#define IWL_OFDM_RATES 8#if IWL == 3945#define IWL_HT_RATES 0#elif IWL == 4965#define IWL_HT_RATES 16#endif#define IWL_MAX_RATES  (IWL_CCK_RATES+IWL_OFDM_RATES+IWL_HT_RATES)/* Time constants */#define SHORT_SLOT_TIME 9#define LONG_SLOT_TIME 20/* RSSI to dBm */#if IWL == 3945#define IWL_RSSI_OFFSET	95#elif IWL == 4965#define IWL_RSSI_OFFSET	44#endif#include "iwl-eeprom.h"#include "iwl-commands.h"#define PCI_LINK_CTRL      0x0F0#define PCI_POWER_SOURCE   0x0C8#define PCI_REG_WUM8       0x0E8#define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT         (0x80000000)/*=== CSR (control and status registers) ===*/#define CSR_BASE    (0x000)#define CSR_SW_VER              (CSR_BASE+0x000)#define CSR_HW_IF_CONFIG_REG    (CSR_BASE+0x000) /* hardware interface config */#define CSR_INT_COALESCING      (CSR_BASE+0x004) /* accum ints, 32-usec units */#define CSR_INT                 (CSR_BASE+0x008) /* host interrupt status/ack */#define CSR_INT_MASK            (CSR_BASE+0x00c) /* host interrupt enable */#define CSR_FH_INT_STATUS       (CSR_BASE+0x010) /* busmaster int status/ack*/#define CSR_GPIO_IN             (CSR_BASE+0x018) /* read external chip pins */#define CSR_RESET               (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/#define CSR_GP_CNTRL            (CSR_BASE+0x024)#define CSR_HW_REV              (CSR_BASE+0x028)#define CSR_EEPROM_REG          (CSR_BASE+0x02c)#define CSR_EEPROM_GP           (CSR_BASE+0x030)#define CSR_GP_UCODE		(CSR_BASE+0x044)#define CSR_UCODE_DRV_GP1       (CSR_BASE+0x054)#define CSR_UCODE_DRV_GP1_SET   (CSR_BASE+0x058)#define CSR_UCODE_DRV_GP1_CLR   (CSR_BASE+0x05c)#define CSR_UCODE_DRV_GP2       (CSR_BASE+0x060)#define CSR_LED_REG		(CSR_BASE+0x094)#define CSR_DRAM_INT_TBL_CTL	(CSR_BASE+0x0A0)#define CSR_GIO_CHICKEN_BITS    (CSR_BASE+0x100)#define CSR_ANA_PLL_CFG         (CSR_BASE+0x20c)#define CSR_HW_REV_WA_REG	(CSR_BASE+0x22C)/* HW I/F configuration */#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MB         (0x00000100)#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MM         (0x00000200)#define CSR_HW_IF_CONFIG_REG_BIT_SKU_MRC            (0x00000400)#define CSR_HW_IF_CONFIG_REG_BIT_BOARD_TYPE         (0x00000800)#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A    (0x00000000)#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B    (0x00001000)#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM     (0x00200000)/* interrupt flags in INTA, set by uCode or hardware (e.g. dma), * acknowledged (reset) by host writing "1" to flagged bits. */#define CSR_INT_BIT_FH_RX        (1<<31) /* Rx DMA, cmd responses, FH_INT[17:16] */#define CSR_INT_BIT_HW_ERR       (1<<29) /* DMA hardware error FH_INT[31] */#define CSR_INT_BIT_DNLD         (1<<28) /* uCode Download */#define CSR_INT_BIT_FH_TX        (1<<27) /* Tx DMA FH_INT[1:0] */#define CSR_INT_BIT_MAC_CLK_ACTV (1<<26) /* NIC controller's clock toggled on/off */#define CSR_INT_BIT_SW_ERR       (1<<25) /* uCode error */#define CSR_INT_BIT_RF_KILL      (1<<7)  /* HW RFKILL switch GP_CNTRL[27] toggled */#define CSR_INT_BIT_CT_KILL      (1<<6)  /* Critical temp (chip too hot) rfkill */#define CSR_INT_BIT_SW_RX        (1<<3)  /* Rx, command responses, 3945 */#define CSR_INT_BIT_WAKEUP       (1<<1)  /* NIC controller waking up (pwr mgmt) */#define CSR_INT_BIT_ALIVE        (1<<0)  /* uCode interrupts once it initializes */#define CSR_INI_SET_MASK	(CSR_INT_BIT_FH_RX   | \				 CSR_INT_BIT_HW_ERR  | \				 CSR_INT_BIT_FH_TX   | \				 CSR_INT_BIT_SW_ERR  | \				 CSR_INT_BIT_RF_KILL | \				 CSR_INT_BIT_SW_RX   | \				 CSR_INT_BIT_WAKEUP  | \				 CSR_INT_BIT_ALIVE)/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */#define CSR_FH_INT_BIT_ERR       (1<<31) /* Error */#define CSR_FH_INT_BIT_HI_PRIOR  (1<<30) /* High priority Rx, bypass coalescing */#define CSR_FH_INT_BIT_RX_CHNL2  (1<<18) /* Rx channel 2 (3945 only) */#define CSR_FH_INT_BIT_RX_CHNL1  (1<<17) /* Rx channel 1 */#define CSR_FH_INT_BIT_RX_CHNL0  (1<<16) /* Rx channel 0 */#define CSR_FH_INT_BIT_TX_CHNL6  (1<<6)  /* Tx channel 6 (3945 only) */#define CSR_FH_INT_BIT_TX_CHNL1  (1<<1)  /* Tx channel 1 */#define CSR_FH_INT_BIT_TX_CHNL0  (1<<0)  /* Tx channel 0 */#define CSR_FH_INT_RX_MASK	(CSR_FH_INT_BIT_HI_PRIOR | \				 CSR_FH_INT_BIT_RX_CHNL2 | \				 CSR_FH_INT_BIT_RX_CHNL1 | \				 CSR_FH_INT_BIT_RX_CHNL0)#define CSR_FH_INT_TX_MASK	(CSR_FH_INT_BIT_TX_CHNL6 | \				 CSR_FH_INT_BIT_TX_CHNL1 | \				 CSR_FH_INT_BIT_TX_CHNL0 )/* RESET */#define CSR_RESET_REG_FLAG_NEVO_RESET                (0x00000001)#define CSR_RESET_REG_FLAG_FORCE_NMI                 (0x00000002)#define CSR_RESET_REG_FLAG_SW_RESET                  (0x00000080)#define CSR_RESET_REG_FLAG_MASTER_DISABLED           (0x00000100)#define CSR_RESET_REG_FLAG_STOP_MASTER               (0x00000200)/* GP (general purpose) CONTROL */#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY        (0x00000001)#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE              (0x00000004)#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ         (0x00000008)#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP         (0x00000010)#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN           (0x00000001)#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE         (0x07000000)#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE         (0x04000000)#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW          (0x08000000)/* EEPROM REG */#define CSR_EEPROM_REG_READ_VALID_MSK	(0x00000001)#define CSR_EEPROM_REG_BIT_CMD		(0x00000002)/* EEPROM GP */#define CSR_EEPROM_GP_VALID_MSK		(0x00000006)#define CSR_EEPROM_GP_BAD_SIGNATURE	(0x00000000)#define CSR_EEPROM_GP_IF_OWNER_MSK	(0x00000180)/* UCODE DRV GP */#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP             (0x00000001)#define CSR_UCODE_SW_BIT_RFKILL                     (0x00000002)#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED           (0x00000004)#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT      (0x00000008)/* GPIO */#define CSR_GPIO_IN_BIT_AUX_POWER                   (0x00000200)#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC                (0x00000000)#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC		CSR_GPIO_IN_BIT_AUX_POWER/* GI Chicken Bits */#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX  (0x00800000)#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER  (0x20000000)/* CSR_ANA_PLL_CFG */#define CSR_ANA_PLL_CFG_SH		(0x00880300)#define CSR_LED_REG_TRUN_ON		(0x00000078)#define CSR_LED_REG_TRUN_OFF		(0x00000038)#define CSR_LED_BSM_CTRL_MSK		(0xFFFFFFDF)/* DRAM_INT_TBL_CTRL */#define CSR_DRAM_INT_TBL_CTRL_EN	(1<<31)#define CSR_DRAM_INT_TBL_CTRL_WRAP_CHK	(1<<27)/*=== HBUS (Host-side Bus) ===*/#define HBUS_BASE	(0x400)#define HBUS_TARG_MEM_RADDR     (HBUS_BASE+0x00c)#define HBUS_TARG_MEM_WADDR     (HBUS_BASE+0x010)#define HBUS_TARG_MEM_WDAT      (HBUS_BASE+0x018)#define HBUS_TARG_MEM_RDAT      (HBUS_BASE+0x01c)#define HBUS_TARG_PRPH_WADDR    (HBUS_BASE+0x044)#define HBUS_TARG_PRPH_RADDR    (HBUS_BASE+0x048)#define HBUS_TARG_PRPH_WDAT     (HBUS_BASE+0x04c)#define HBUS_TARG_PRPH_RDAT     (HBUS_BASE+0x050)#define HBUS_TARG_WRPTR         (HBUS_BASE+0x060)#define HBUS_TARG_MBX_C         (HBUS_BASE+0x030)/* SCD (Scheduler) */#define SCD_BASE                        (CSR_BASE + 0x2E00)

⌨️ 快捷键说明

复制代码 Ctrl + C
搜索代码 Ctrl + F
全屏模式 F11
切换主题 Ctrl + Shift + D
显示快捷键 ?
增大字号 Ctrl + =
减小字号 Ctrl + -