csr.c

这是Linux环境下的蓝牙源代码

		return "Bluetooth address + link key 7";
	case CSR_PSKEY_LOCAL_SUPPORTED_COMMANDS:
		return "Local supported commands";
	case CSR_PSKEY_LM_MAX_ABSENCE_INDEX:
		return "Maximum absence index allowed";
	case CSR_PSKEY_DEVICE_NAME:
		return "Local device's \"user friendly\" name";
	case CSR_PSKEY_AFH_RSSI_THRESHOLD:
		return "AFH RSSI threshold";
	case CSR_PSKEY_LM_CASUAL_SCAN_INTERVAL:
		return "Scan interval in slots for casual scanning";
	case CSR_PSKEY_AFH_MIN_MAP_CHANGE:
		return "The minimum amount to change an AFH map by";
	case CSR_PSKEY_AFH_RSSI_LP_RUN_PERIOD:
		return "AFH RSSI reading period when in low power mode";
	case CSR_PSKEY_HCI_LMP_LOCAL_VERSION:
		return "The HCI and LMP version reported locally";
	case CSR_PSKEY_LMP_REMOTE_VERSION:
		return "The LMP version reported remotely";
	case CSR_PSKEY_HOLD_ERROR_MESSAGE_NUMBER:
		return "Maximum number of queued HCI Hardware Error Events";
	case CSR_PSKEY_DFU_ATTRIBUTES:
		return "DFU attributes";
	case CSR_PSKEY_DFU_DETACH_TO:
		return "DFU detach timeout";
	case CSR_PSKEY_DFU_TRANSFER_SIZE:
		return "DFU transfer size";
	case CSR_PSKEY_DFU_ENABLE:
		return "DFU enable";
	case CSR_PSKEY_DFU_LIN_REG_ENABLE:
		return "Linear Regulator enabled at boot in DFU mode";
	case CSR_PSKEY_DFUENC_VMAPP_PK_MODULUS_MSB:
		return "DFU encryption VM application public key MSB";
	case CSR_PSKEY_DFUENC_VMAPP_PK_MODULUS_LSB:
		return "DFU encryption VM application public key LSB";
	case CSR_PSKEY_DFUENC_VMAPP_PK_M_DASH:
		return "DFU encryption VM application M dash";
	case CSR_PSKEY_DFUENC_VMAPP_PK_R2N_MSB:
		return "DFU encryption VM application public key R2N MSB";
	case CSR_PSKEY_DFUENC_VMAPP_PK_R2N_LSB:
		return "DFU encryption VM application public key R2N LSB";
	case CSR_PSKEY_BCSP_LM_PS_BLOCK:
		return "BCSP link establishment block";
	case CSR_PSKEY_HOSTIO_FC_PS_BLOCK:
		return "HCI flow control block";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO0:
		return "Host transport channel 0 settings (BCSP ACK)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO1:
		return "Host transport channel 1 settings (BCSP-LE)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO2:
		return "Host transport channel 2 settings (BCCMD)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO3:
		return "Host transport channel 3 settings (HQ)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO4:
		return "Host transport channel 4 settings (DM)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO5:
		return "Host transport channel 5 settings (HCI CMD/EVT)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO6:
		return "Host transport channel 6 settings (HCI ACL)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO7:
		return "Host transport channel 7 settings (HCI SCO)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO8:
		return "Host transport channel 8 settings (L2CAP)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO9:
		return "Host transport channel 9 settings (RFCOMM)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO10:
		return "Host transport channel 10 settings (SDP)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO11:
		return "Host transport channel 11 settings (TEST)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO12:
		return "Host transport channel 12 settings (DFU)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO13:
		return "Host transport channel 13 settings (VM)";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO14:
		return "Host transport channel 14 settings";
	case CSR_PSKEY_HOSTIO_PROTOCOL_INFO15:
		return "Host transport channel 15 settings";
	case CSR_PSKEY_HOSTIO_UART_RESET_TIMEOUT:
		return "UART reset counter timeout";
	case CSR_PSKEY_HOSTIO_USE_HCI_EXTN:
		return "Use hci_extn to route non-hci channels";
	case CSR_PSKEY_HOSTIO_USE_HCI_EXTN_CCFC:
		return "Use command-complete flow control for hci_extn";
	case CSR_PSKEY_HOSTIO_HCI_EXTN_PAYLOAD_SIZE:
		return "Maximum hci_extn payload size";
	case CSR_PSKEY_BCSP_LM_CNF_CNT_LIMIT:
		return "BCSP link establishment conf message count";
	case CSR_PSKEY_HOSTIO_MAP_SCO_PCM:
		return "Map SCO over PCM";
	case CSR_PSKEY_HOSTIO_AWKWARD_PCM_SYNC:
		return "PCM interface synchronisation is difficult";
	case CSR_PSKEY_HOSTIO_BREAK_POLL_PERIOD:
		return "Break poll period (microseconds)";
	case CSR_PSKEY_HOSTIO_MIN_UART_HCI_SCO_SIZE:
		return "Minimum SCO packet size sent to host over UART HCI";
	case CSR_PSKEY_HOSTIO_MAP_SCO_CODEC:
		return "Map SCO over the built-in codec";
	case CSR_PSKEY_PCM_CVSD_TX_HI_FREQ_BOOST:
		return "High frequency boost for PCM when transmitting CVSD";
	case CSR_PSKEY_PCM_CVSD_RX_HI_FREQ_BOOST:
		return "High frequency boost for PCM when receiving CVSD";
	case CSR_PSKEY_PCM_CONFIG32:
		return "PCM interface settings bitfields";
	case CSR_PSKEY_USE_OLD_BCSP_LE:
		return "Use the old version of BCSP link establishment";
	case CSR_PSKEY_PCM_CVSD_USE_NEW_FILTER:
		return "CVSD uses the new filter if available";
	case CSR_PSKEY_PCM_FORMAT:
		return "PCM data format";
	case CSR_PSKEY_CODEC_OUT_GAIN:
		return "Audio output gain when using built-in codec";
	case CSR_PSKEY_CODEC_IN_GAIN:
		return "Audio input gain when using built-in codec";
	case CSR_PSKEY_CODEC_PIO:
		return "PIO to enable when built-in codec is enabled";
	case CSR_PSKEY_PCM_LOW_JITTER_CONFIG:
		return "PCM interface settings for low jitter master mode";
	case CSR_PSKEY_HOSTIO_SCO_PCM_THRESHOLDS:
		return "Thresholds for SCO PCM buffers";
	case CSR_PSKEY_HOSTIO_SCO_HCI_THRESHOLDS:
		return "Thresholds for SCO HCI buffers";
	case CSR_PSKEY_HOSTIO_MAP_SCO_PCM_SLOT:
		return "Route SCO data to specified slot in pcm frame";
	case CSR_PSKEY_UART_BAUDRATE:
		return "UART Baud rate";
	case CSR_PSKEY_UART_CONFIG_BCSP:
		return "UART configuration when using BCSP";
	case CSR_PSKEY_UART_CONFIG_H4:
		return "UART configuration when using H4";
	case CSR_PSKEY_UART_CONFIG_H5:
		return "UART configuration when using H5";
	case CSR_PSKEY_UART_CONFIG_USR:
		return "UART configuration when under VM control";
	case CSR_PSKEY_UART_TX_CRCS:
		return "Use CRCs for BCSP or H5";
	case CSR_PSKEY_UART_ACK_TIMEOUT:
		return "Acknowledgement timeout for BCSP and H5";
	case CSR_PSKEY_UART_TX_MAX_ATTEMPTS:
		return "Max times to send reliable BCSP or H5 message";
	case CSR_PSKEY_UART_TX_WINDOW_SIZE:
		return "Transmit window size for BCSP and H5";
	case CSR_PSKEY_UART_HOST_WAKE:
		return "UART host wakeup";
	case CSR_PSKEY_HOSTIO_THROTTLE_TIMEOUT:
		return "Host interface performance control.";
	case CSR_PSKEY_PCM_ALWAYS_ENABLE:
		return "PCM port is always enable when chip is running";
	case CSR_PSKEY_UART_HOST_WAKE_SIGNAL:
		return "Signal to use for uart host wakeup protocol";
	case CSR_PSKEY_UART_CONFIG_H4DS:
		return "UART configuration when using H4DS";
	case CSR_PSKEY_H4DS_WAKE_DURATION:
		return "How long to spend waking the host when using H4DS";
	case CSR_PSKEY_H4DS_MAXWU:
		return "Maximum number of H4DS Wake-Up messages to send";
	case CSR_PSKEY_H4DS_LE_TIMER_PERIOD:
		return "H4DS Link Establishment Tsync and Tconf period";
	case CSR_PSKEY_H4DS_TWU_TIMER_PERIOD:
		return "H4DS Twu timer period";
	case CSR_PSKEY_H4DS_UART_IDLE_TIMER_PERIOD:
		return "H4DS Tuart_idle timer period";
	case CSR_PSKEY_ANA_FTRIM:
		return "Crystal frequency trim";
	case CSR_PSKEY_WD_TIMEOUT:
		return "Watchdog timeout (microseconds)";
	case CSR_PSKEY_WD_PERIOD:
		return "Watchdog period (microseconds)";
	case CSR_PSKEY_HOST_INTERFACE:
		return "Host interface";
	case CSR_PSKEY_HQ_HOST_TIMEOUT:
		return "HQ host command timeout";
	case CSR_PSKEY_HQ_ACTIVE:
		return "Enable host query task?";
	case CSR_PSKEY_BCCMD_SECURITY_ACTIVE:
		return "Enable configuration security";
	case CSR_PSKEY_ANA_FREQ:
		return "Crystal frequency";
	case CSR_PSKEY_PIO_PROTECT_MASK:
		return "Access to PIO pins";
	case CSR_PSKEY_PMALLOC_SIZES:
		return "pmalloc sizes array";
	case CSR_PSKEY_UART_BAUD_RATE:
		return "UART Baud rate (pre 18)";
	case CSR_PSKEY_UART_CONFIG:
		return "UART configuration bitfield";
	case CSR_PSKEY_STUB:
		return "Stub";
	case CSR_PSKEY_TXRX_PIO_CONTROL:
		return "TX and RX PIO control";
	case CSR_PSKEY_ANA_RX_LEVEL:
		return "ANA_RX_LVL register initial value";
	case CSR_PSKEY_ANA_RX_FTRIM:
		return "ANA_RX_FTRIM register initial value";
	case CSR_PSKEY_PSBC_DATA_VERSION:
		return "Persistent store version";
	case CSR_PSKEY_PCM0_ATTENUATION:
		return "Volume control on PCM channel 0";
	case CSR_PSKEY_LO_LVL_MAX:
		return "Maximum value of LO level control register";
	case CSR_PSKEY_LO_ADC_AMPL_MIN:
		return "Minimum value of the LO amplitude measured on the ADC";
	case CSR_PSKEY_LO_ADC_AMPL_MAX:
		return "Maximum value of the LO amplitude measured on the ADC";
	case CSR_PSKEY_IQ_TRIM_CHANNEL:
		return "IQ calibration channel";
	case CSR_PSKEY_IQ_TRIM_GAIN:
		return "IQ calibration gain";
	case CSR_PSKEY_IQ_TRIM_ENABLE:
		return "IQ calibration enable";
	case CSR_PSKEY_TX_OFFSET_HALF_MHZ:
		return "Transmit offset";
	case CSR_PSKEY_GBL_MISC_ENABLES:
		return "Global miscellaneous hardware enables";
	case CSR_PSKEY_UART_SLEEP_TIMEOUT:
		return "Time in ms to deep sleep if nothing received";
	case CSR_PSKEY_DEEP_SLEEP_STATE:
		return "Deep sleep state usage";
	case CSR_PSKEY_IQ_ENABLE_PHASE_TRIM:
		return "IQ phase enable";
	case CSR_PSKEY_HCI_HANDLE_FREEZE_PERIOD:
		return "Time for which HCI handle is frozen after link removal";
	case CSR_PSKEY_MAX_FROZEN_HCI_HANDLES:
		return "Maximum number of frozen HCI handles";
	case CSR_PSKEY_PAGETABLE_DESTRUCTION_DELAY:
		return "Delay from freezing buf handle to deleting page table";
	case CSR_PSKEY_IQ_TRIM_PIO_SETTINGS:
		return "IQ PIO settings";
	case CSR_PSKEY_USE_EXTERNAL_CLOCK:
		return "Device uses an external clock";
	case CSR_PSKEY_DEEP_SLEEP_WAKE_CTS:
		return "Exit deep sleep on CTS line activity";
	case CSR_PSKEY_FC_HC2H_FLUSH_DELAY:
		return "Delay from disconnect to flushing HC->H FC tokens";
	case CSR_PSKEY_RX_HIGHSIDE:
		return "Disable the HIGHSIDE bit in ANA_CONFIG";
	case CSR_PSKEY_TX_PRE_LVL:
		return "TX pre-amplifier level";
	case CSR_PSKEY_RX_SINGLE_ENDED:
		return "RX single ended";
	case CSR_PSKEY_TX_FILTER_CONFIG:
		return "TX filter configuration";
	case CSR_PSKEY_CLOCK_REQUEST_ENABLE:
		return "External clock request enable";
	case CSR_PSKEY_RX_MIN_ATTEN:
		return "Minimum attenuation allowed for receiver";
	case CSR_PSKEY_XTAL_TARGET_AMPLITUDE:
		return "Crystal target amplitude";
	case CSR_PSKEY_PCM_MIN_CPU_CLOCK:
		return "Minimum CPU clock speed with PCM port running";
	case CSR_PSKEY_HOST_INTERFACE_PIO_USB:
		return "USB host interface selection PIO line";
	case CSR_PSKEY_CPU_IDLE_MODE:
		return "CPU idle mode when radio is active";
	case CSR_PSKEY_DEEP_SLEEP_CLEAR_RTS:
		return "Deep sleep clears the UART RTS line";
	case CSR_PSKEY_RF_RESONANCE_TRIM:
		return "Frequency trim for IQ and LNA resonant circuits";
	case CSR_PSKEY_DEEP_SLEEP_PIO_WAKE:
		return "PIO line to wake the chip from deep sleep";
	case CSR_PSKEY_DRAIN_BORE_TIMERS:
		return "Energy consumption measurement settings";
	case CSR_PSKEY_DRAIN_TX_POWER_BASE:
		return "Energy consumption measurement settings";
	case CSR_PSKEY_MODULE_ID:
		return "Module serial number";
	case CSR_PSKEY_MODULE_DESIGN:
		return "Module design ID";
	case CSR_PSKEY_MODULE_SECURITY_CODE:
		return "Module security code";
	case CSR_PSKEY_VM_DISABLE:
		return "VM disable";
	case CSR_PSKEY_MOD_MANUF0:
		return "Module manufactuer data 0";
	case CSR_PSKEY_MOD_MANUF1:
		return "Module manufactuer data 1";
	case CSR_PSKEY_MOD_MANUF2:
		return "Module manufactuer data 2";
	case CSR_PSKEY_MOD_MANUF3:
		return "Module manufactuer data 3";
	case CSR_PSKEY_MOD_MANUF4:
		return "Module manufactuer data 4";
	case CSR_PSKEY_MOD_MANUF5:
		return "Module manufactuer data 5";
	case CSR_PSKEY_MOD_MANUF6:
		return "Module manufactuer data 6";
	case CSR_PSKEY_MOD_MANUF7:
		return "Module manufactuer data 7";
	case CSR_PSKEY_MOD_MANUF8:
		return "Module manufactuer data 8";
	case CSR_PSKEY_MOD_MANUF9:
		return "Module manufactuer data 9";
	case CSR_PSKEY_DUT_VM_DISABLE:
		return "VM disable when entering radiotest modes";
	case CSR_PSKEY_USR0:
		return "User configuration data 0";
	case CSR_PSKEY_USR1:
		return "User configuration data 1";
	case CSR_PSKEY_USR2:
		return "User configuration data 2";
	case CSR_PSKEY_USR3:
		return "User configuration data 3";
	case CSR_PSKEY_USR4:
		return "User configuration data 4";
	case CSR_PSKEY_USR5:
		return "User configuration data 5";
	case CSR_PSKEY_USR6:
		return "User configuration data 6";
	case CSR_PSKEY_USR7:
		return "User configuration data 7";
	case CSR_PSKEY_USR8:
		return "User configuration data 8";
	case CSR_PSKEY_USR9:
		return "User configuration data 9";
	case CSR_PSKEY_USR10:
		return "User configuration data 10";
	case CSR_PSKEY_USR11:
		return "User configuration data 11";
	case CSR_PSKEY_USR12:
		return "User configuration data 12";
	case CSR_PSKEY_USR13:
		return "User configuration data 13";
	case CSR_PSKEY_USR14:
		return "User configuration data 14";
	case CSR_PSKEY_USR15:
		return "User configuration data 15";
	case CSR_PSKEY_USR16:
		return "User configuration data 16";
	case CSR_PSKEY_USR17:
		return "User configuration data 17";
	case CSR_PSKEY_USR18:
		return "User configuration data 18";
	case CSR_PSKEY_USR19:
		return "User configuration data 19";
	case CSR_PSKEY_USR20:
		return "User configuration data 20";
	case CSR_PSKEY_USR21:
		return "User configuration data 21";
	case CSR_PSKEY_USR22:
		return "User configuration data 22";
	case CSR_PSKEY_USR23:
		return "User configuration data 23";
	case CSR_PSKEY_USR24:
		return "User configuration data 24";
	case CSR_PSKEY_USR25:
		return "User configuration data 25";
	case CSR_PSKEY_USR26:
		return "User configuration data 26";
	case CSR_PSKEY_USR27:
		return "User configuration data 27";
	case CSR_PSKEY_USR28:
		return "User configuration data 28";
	case CSR_PSKEY_USR29:
		return "User configuration data 29";
	case CSR_PSKEY_USR30:
		return "User configuration data 30";
	case CSR_PSKEY_USR31:
		return "User configuration data 31";
	case CSR_PSKEY_USR32:
		return "User configuration data 32";
	case CSR_PSKEY_USR33:
		return "User configuration data 33";
	case CSR_PSKEY_USR34:
		return "User configuration data 34";
	case CSR_PSKEY_USR35:
		return "User configuration data 35";
	case CSR_PSKEY_USR36:
		return "User configuration data 36";
	case CSR_PSKEY_USR37:
		return "User configuration data 37";
	case CSR_PSKEY_USR38:
		return "User configuration data 38";
	case CSR_PSKEY_USR39:
		return "User configuration data 39";
	case CSR_PSKEY_USR40:
		return "User configuration data 40";
	case CSR_PSKEY_USR41:
		return "User configuration data 41";
	case CSR_PSKEY_USR42:
		return "User configuration data 42";
	case CSR_PSKEY_USR43:
		return "User configuration data 43";
	case CSR_PSKEY_USR44:
		return "User configuration data 44";
	case CSR_PSKEY_USR45:
		return "User configuration data 45";
	case CSR_PSKEY_USR46:
		return "User configuration data 46";
	case CSR_PSKEY_USR47:
		return "User configuration data 47";
	case CSR_PSKEY_USR48:
		return "User configuration data 48";
	case CSR_PSKEY_USR49:
		return "User configuration data 49";
	case CSR_PSKEY_USB_VERSION:
		return "USB specification version number";
	case CSR_PSKEY_USB_DEVICE_CLASS_CODES: