peizhi2.6.txt

在2410内核的基础上移植2.6内核的步骤

# CONFIG_NLS_ASCII is not set
# CONFIG_NLS_ISO8859_1 is not set
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
 
# Profiling support
# CONFIG_PROFILING is not set
 
# Graphics support
CONFIG_FB=y
# CONFIG_FB_MODE_HELPERS is not set
# CONFIG_FB_TILEBLITTING is not set
CONFIG_FB_VIRTUAL=y
 
# Console display driver support
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
# CONFIG_FONT_8x16 is not set
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
 
# Logo configuration
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=m
CONFIG_BACKLIGHT_DEVICE=y
CONFIG_LCD_CLASS_DEVICE=m
CONFIG_LCD_DEVICE=y
 
# Sound
# CONFIG_SOUND is not set
 
# Misc devices
 
# USB support
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
 
# Miscellaneous USB options
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
CONFIG_USB_ARCH_HAS_HCD=y
# CONFIG_USB_ARCH_HAS_OHCI is not set
 
# USB Host Controller Drivers
# CONFIG_USB_SL811_HCD is not set
 
# USB Device Class drivers
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
 
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_RW_DETECT is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_HP8200e=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
 
# USB Input Devices
# CONFIG_USB_HID is not set
 
# USB HID Boot Protocol drivers
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
 
# USB Imaging devices
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
 
# USB Multimedia devices
# CONFIG_USB_DABUSB is not set
# CONFIG_USB_VICAM is not set
# CONFIG_USB_DSBR is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_KONICAWC is not set
CONFIG_USB_OV511=m
# CONFIG_USB_SE401 is not set
CONFIG_USB_SN9C102=m
# CONFIG_USB_STV680 is not set
 
# USB Network Adapters
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
 
# USB port drivers
 
# USB Serial Converter support
# CONFIG_USB_SERIAL is not set
 
# USB Miscellaneous drivers
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_TEST is not set
 
# USB ATM/DSL drivers
 
# USB Gadget Support
# CONFIG_USB_GADGET is not set
 
# MMC/SD Card support
# CONFIG_MMC is not set
 
# Kernel hacking
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
CONFIG_FRAME_POINTER=y
CONFIG_DEBUG_USER=y
# CONFIG_DEBUG_WAITQ is not set
CONFIG_DEBUG_ERRORS=y
CONFIG_DEBUG_LL=y
# CONFIG_DEBUG_ICEDCC is not set
CONFIG_DEBUG_S3C2410_PORT=y
CONFIG_DEBUG_S3C2410_UART=0
 
# Security options
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
 
# Cryptographic options
# CONFIG_CRYPTO is not set
 
# Hardware crypto devices
 
# Library routines
CONFIG_CRC_CCITT=y
CONFIG_CRC32=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
发表于 @ 2007年08月18日 22:36:00|评论(24)|编辑

旧一篇: 三个境界——致计算机系的同学们
  
 
最新笔记本游戏技术开发套件 
提供更畅快的用户体验 游戏带着走 
金旭亮.NET系列之《静态网页技术》
这是Web用户界面设计师主要关注的领域 是动态网页设计技术领域必要的知识与技术基础评论
#huanggang982 发表于2007-09-17 20:51:42  IP: 218.3.22.*
先参考您的指南在博创板子上试试,在此先谢谢了！#huanggang982 发表于2007-09-17 20:54:50  IP: 218.3.22.*
你写的内核下载地址是linux2.6.11.7的地址，是不是没什么影响？#skywalker_nick 发表于2007-09-18 08:57:17  IP: 61.155.18.*
一开始用的11.7版, 编译时有问题, 后来转到14版后就好了...写的时候忘改了...不好意思~~~
我就是在uptech 2410-s上做的~~~#student 发表于2007-09-27 10:15:48  IP: 210.29.96.*
你给的那个文件系统的下载地址，下载下来后怎么解压时出错呢，还有其他的地方可以下吗，我都没找到，谢了！#skywalker_nick 发表于2007-09-27 13:13:15  IP: 61.155.18.*
我把文件放到了163的邮箱里, 你可以自己去下载...
user: nick_ma25
password: nick25

里面的文件有一份网上流传很广的linux移植指南还有你需要的yaff2源码...
#小闭 发表于2007-10-08 11:29:19  IP: 202.193.15.*
好东西！
我的已经一直成功了！#务实进取 发表于2007-10-17 20:39:22  IP: 58.252.15.*
大侠，可以发你的2.6内核和根文件系统给我吗？我按你方法做了，但是，还是不成功！我在uptech2410s上跑的。搞了很久了，都没有成功！你希望你难发内核和文件系统给我，我就可以测试，是内核错误，还是根文件系统错误了。我的邮箱地址：[e-mail]
QQ:79882173#skywalker_nick 发表于2007-10-18 09:51:50  IP: 61.155.18.*
好的~~~~等等我发下~~~~
这个是我的内核启动信息:
Linux version 2.6.14 (root@debian) (gcc version 3.4.1) #2 Wed Oct 10 20:09:11 CST 2007
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
Machine: SMDK2410
Converting old-style param struct to taglist
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2410 (id 0x32410000)
S3C2410: core 202.800 MHz, memory 101.400 MHz, peripheral 50.700 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
USB Control, (c) 2006
On node 0 totalpages: 16384
DMA zone: 16384 pages, LIFO batch:7
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0,115200
irq: clearing pending ext status 00000100
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
PID hash table entries: 512 (order: 9, 8192 bytes)
timer tcon=00000000, tcnt a509, tcfg 00000200,00000000, usec 00001e4c
Console: colour dummy device 80x30
selected clock c025a61c (pclk) quot 27, calc 113169
Dentry cache hash table entries: 16384 (order: 4, 65536 by#skywalker_nick 发表于2007-10-18 09:56:26  IP: 61.155.18.*
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 62080KB available (2081K code, 550K data, 96K init)
Calibrating delay loop... 101.17 BogoMIPS (lpj=252928)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
softlockup thread 0 started up.
NET: Registered protocol family 16
S3C2410: Initialising architecture
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
NetWinder Floating Point Emulator V0.97 (double precision)
devfs: 2004-01-31 Richard Gooch ([e-mail])
devfs: boot_options: 0x1
yaffs Oct 10 2007 20:05:00 Installing. 
s3c2410fb: LCDSADDR1 = 0x00000000
s3c2410fb: LCDSADDR2 = 0x00000000
s3c2410fb: LCDSADDR3 = 0x00000000
s3c2410fb: LPCSEL = 0x00000000
s3c2410fb: replacing TPAL 00000000
s3c2410fb: devinit
s3c2410fb: got LCD region
s3c2410fb: got and enabled clock
s3c2410fb: map_video_memory(fbi=c036c240)
s3c2410fb: map_video_memory: clear ffc00000:00096000
s3c2410fb: map_video_memory: dma=33d00000 cpu=ffc00000 size=00096000
s3c2410fb: got video memory
s3c2410fb: LCDSADDR1 = 0x19e80000
s3c2410f#skywalker_nick 发表于2007-10-18 10:11:07  IP: 61.155.18.*
s3c2410fb: LCDSADDR2 = 0x19ecb000
s3c2410fb: LCDSADDR3 = 0x00000280
Console: switching to colour frame buffer device 80x60
fb0: s3c2410fb frame buffer device
S3C2410 RTC, (c) 2004 Simtec Electronics
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Linux video capture interface: v1.00
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand: mapped registers at c4880000
s3c2410-nand: timing: Tacls 10ns, Twrph0 30ns, Twrph1 10ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Creating 5 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00020000 : "loader"
0x00020000-0x00030000 : "param"
0x00030000-0x00230000 : "kernel"
0x00230000-0x00530000 : "rootfs"
0x00530000-0x03f30000 : "yaffs"
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x4900#skywalker_nick 发表于2007-10-18 10:11:36  IP: 61.155.18.*
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usb 1-1: new full speed USB device using s3c2410-ohci and address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing init memory: 96K
selected clock c025a61c (pclk) quot 27, calc 113169
selected clock c025a61c (pclk) quot 27, calc 113169
selected clock c025a61c (pclk) quot 27, calc 113169
selected clock c025a61c (pclk) quot 27, calc 113169
selected clock c025a61c (pclk) quot 27, calc 113169
yaffs: dev is 32505860 name is "mtdblock4"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.4, "mtdblock4"#eszent 发表于2007-12-25 22:29:53  IP: 219.137.200.*
好#白兰瓜 发表于2008-01-28 16:46:24  IP: 123.64.87.*
楼主您好，这两天一直按照你的指南在博创的uptech2410s上进行移植，但总是卡在下面的地方：

VFS: Mounted root (cramfs filesystem) readonly.

Mounted devfs on /dev

Freeing init memory: 92K

Failed to execute /linuxrc. Attempting defaults...

Kernel panic - not syncing: No init found. Try passing init= option to kernel.

不知您能否将编译好的zImage和root.cramfs发给我，我好定位一下错误。[e-mail]，谢谢。

2008-01-28 18:36:17作者回复
这种情况一般是传递给内核的参数问题，用来指定你的根文件系统所在flash分区的那个参数。<br />可以，我可以传给你看看。#白兰瓜 发表于2008-01-28 23:18:47  IP: 123.64.87.*
收到了，非常感谢。我也觉得是配置问题，但是一直没办法定位。
等我解决了，一定来这里汇报 :)# zhy 发表于2008-03-25 20:27:42  IP: 221.7.40.*