ehci-fehci.h

WiFi IP-Cam solution. FIC8120 platform VIA VT6656 USB Module driver source code.

/*
 * Copyright (c) 2001-2002 by David Brownell
 * 
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the
 * Free Software Foundation; either version 2 of the License, or (at your
 * option) any later version.
 *
 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
 * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
 * for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software Foundation,
 * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */

#ifndef __LINUX_EHCI_HCD_H
#define __LINUX_EHCI_HCD_H

/* definitions used for the EHCI driver */

/* statistics can be kept for for tuning/monitoring */
struct ehci_stats {
	/* irq usage */
	unsigned long		normal;
	unsigned long		error;
	unsigned long		reclaim;

	/* termination of urbs from core */
	unsigned long		complete;
	unsigned long		unlink;
};

/* ehci_hcd->lock guards shared data against other CPUs:
 *   ehci_hcd:	async, reclaim, periodic (and shadow), ...
 *   hcd_dev:	ep[]
 *   ehci_qh:	qh_next, qtd_list
 *   ehci_qtd:	qtd_list
 *
 * Also, hold this lock when talking to HC registers or
 * when updating hw_* fields in shared qh/qtd/... structures.
 */

#define	EHCI_MAX_ROOT_PORTS	15		/* see HCS_N_PORTS */

struct ehci_hcd {			/* one per controller */
	spinlock_t		lock;

	struct otg_transceiver	*transceiver; //For OTG  Add  by Einsn@VIA
	/* async schedule support */
	struct ehci_qh		*async;
	struct ehci_qh		*reclaim;
	int			reclaim_ready : 1,
				async_idle : 1;

	/* periodic schedule support */
#define	DEFAULT_I_TDPS		1024		/* some HCs can do less */
	unsigned		periodic_size;
	u32			*periodic;	/* hw periodic table */
	dma_addr_t		periodic_dma;
	unsigned		i_thresh;	/* uframes HC might cache */

	union ehci_shadow	*pshadow;	/* mirror hw periodic table */
	int			next_uframe;	/* scan periodic, start here */
	unsigned		periodic_sched;	/* periodic activity count */

	/* per root hub port */
	unsigned long		reset_done [EHCI_MAX_ROOT_PORTS];

	/* glue to PCI and HCD framework */
	struct usb_hcd		hcd;
	struct ehci_caps	*caps;
	struct ehci_regs	*regs;
	u32			hcs_params;	/* cached register copy */

	/* per-HC memory pools (could be per-PCI-bus, but ...) */
	struct pci_pool		*qh_pool;	/* qh per active urb */
	struct pci_pool		*qtd_pool;	/* one or more per qh */
	struct pci_pool		*itd_pool;	/* itd per iso urb */
	struct pci_pool		*sitd_pool;	/* sitd per split iso urb */

	struct timer_list	watchdog;
	unsigned		stamp;

#ifdef EHCI_STATS
	struct ehci_stats	stats;
#	define COUNT(x) do { (x)++; } while (0)
#else
#	define COUNT(x) do {} while (0)
#endif
};

/* unwrap an HCD pointer to get an EHCI_HCD pointer */ 
#define hcd_to_ehci(hcd_ptr)  list_entry(hcd_ptr, struct ehci_hcd, hcd)

/* NOTE:  urb->transfer_flags expected to not use this bit !!! */
#define EHCI_STATE_UNLINK	0x8000		/* urb being unlinked */

/*-------------------------------------------------------------------------*/

/* EHCI register interface, corresponds to EHCI Revision 0.95 specification */

/* Section 2.2 Host Controller Capability Registers */
struct ehci_caps {
	u8		length;		/* CAPLENGTH - size of this struct */
	u8		reserved;       /* offset 0x1 */
	u16		hci_version;    /* HCIVERSION - offset 0x2 */
	u32		hcs_params;     /* HCSPARAMS - offset 0x4 */
#define HCS_DEBUG_PORT(p)	(((p)>>20)&0xf)	/* bits 23:20, debug port? */
#define HCS_INDICATOR(p)	((p)&(1 << 16))	/* true: has port indicators */
#define HCS_N_CC(p)		(((p)>>12)&0xf)	/* bits 15:12, #companion HCs */
#define HCS_N_PCC(p)		(((p)>>8)&0xf)	/* bits 11:8, ports per CC */
#define HCS_PORTROUTED(p)	((p)&(1 << 7))	/* true: port routing */ 
#define HCS_PPC(p)		((p)&(1 << 4))	/* true: port power control */ 
#define HCS_N_PORTS(p)		(((p)>>0)&0xf)	/* bits 3:0, ports on HC */

	u32		hcc_params;      /* HCCPARAMS - offset 0x8 */
#define HCC_EXT_CAPS(p)		(((p)>>8)&0xff)	/* for pci extended caps */
#define HCC_ISOC_CACHE(p)       ((p)&(1 << 7))  /* true: can cache isoc frame */
#define HCC_ISOC_THRES(p)       (((p)>>4)&0x7)  /* bits 6:4, uframes cached */
#define HCC_CANPARK(p)		((p)&(1 << 2))  /* true: can park on async qh */
#define HCC_PGM_FRAMELISTLEN(p) ((p)&(1 << 1))  /* true: periodic_size changes*/
#define HCC_64BIT_ADDR(p)       ((p)&(1))       /* true: can use 64-bit addr */

#ifndef CONFIG_FARADAY_FEHCI //######################### For FEHCI  Add by Einsn @VIA
	u8		portroute [8];	 /* nibbles for routing - offset 0xC */
#endif
} __attribute__ ((packed));


/* Section 2.3 Host Controller Operational Registers */
struct ehci_regs {

	/* USBCMD: offset 0x00 */
	u32		command;
/* 23:16 is r/w intr rate, in microframes; default "8" == 1/msec */
#define CMD_PARK	(1<<11)		/* enable "park" on async qh */
#define CMD_PARK_CNT(c)	(((c)>>8)&3)	/* how many transfers to park for */
#define CMD_LRESET	(1<<7)		/* partial reset (no ports, etc) */
#define CMD_IAAD	(1<<6)		/* "doorbell" interrupt async advance */
#define CMD_ASE		(1<<5)		/* async schedule enable */
#define CMD_PSE  	(1<<4)		/* periodic schedule enable */
/* 3:2 is periodic frame list size */
#define CMD_RESET	(1<<1)		/* reset HC not bus */
#define CMD_RUN		(1<<0)		/* start/stop HC */

	/* USBSTS: offset 0x04 */
	u32		status;
#define STS_ASS		(1<<15)		/* Async Schedule Status */
#define STS_PSS		(1<<14)		/* Periodic Schedule Status */
#define STS_RECL	(1<<13)		/* Reclamation */
#define STS_HALT	(1<<12)		/* Not running (any reason) */
/* some bits reserved */
	/* these STS_* flags are also intr_enable bits (USBINTR) */
#define STS_IAA		(1<<5)		/* Interrupted on async advance */
#define STS_FATAL	(1<<4)		/* such as some PCI access errors */
#define STS_FLR		(1<<3)		/* frame list rolled over */
#define STS_PCD		(1<<2)		/* port change detect */
#define STS_ERR		(1<<1)		/* "error" completion (overflow, ...) */
#define STS_INT		(1<<0)		/* "normal" completion (short, ...) */

//Modify by Einsn@VIA
	/* USBINTR: offset 0x08 */
	u32		intr_enable;

	/* FRINDEX: offset 0x0C */
	u32		frame_index;	/* current microframe number */
#ifdef CONFIG_FARADAY_FEHCI //######################### For FEHCI
  u32    reserved [1];
#else  /* Standard EHCI HC*/
  /* CTRLDSSEGMENT: offset 0x10 */
  u32    segment;   /* address bits 63:32 if needed */
#endif
	/* PERIODICLISTBASE: offset 0x14 */
	u32		frame_list; 	/* points to periodic list */
	/* ASYNCICLISTADDR: offset 0x18 */
	u32		async_next;	/* address of next async queue head */

#ifdef CONFIG_FARADAY_FEHCI //######################### For FEHCI
  u32    reserved2 [1];
#else  /* Standard EHCI HC*/
  u32    reserved [9];
  /* CONFIGFLAG: offset 0x40 */
  u32    configured_flag;
#define FLAG_CF    (1<<0)    /* true: we'll support "high speed" */
#endif


	/* PORTSC: offset 0x44 */
#ifdef CONFIG_FARADAY_FEHCI //######################### For FEHCI
  u32    port_status [1];  /* up to N_PORTS */
#else
  u32    port_status [0];  /* up to N_PORTS */
#endif


/* 31:23 reserved */
#define PORT_WKOC_E	(1<<22)		/* wake on overcurrent (enable) */
#define PORT_WKDISC_E	(1<<21)		/* wake on disconnect (enable) */
#define PORT_WKCONN_E	(1<<20)		/* wake on connect (enable) */
/* 19:16 for port testing */
/* 15:14 for using port indicator leds (if HCS_INDICATOR allows) */
#ifdef CONFIG_FARADAY_FEHCI//John_Update
//#define PORT_OWNER	(1<<13)	//John Remove	/* true: companion hc owns this port */  //FHUSB200 doon't have this function
//#define PORT_POWER	(1<<12)	//John Remove	/* true: has power (see PPC) */  //FHUSB200 doon't have this function
//#define PORT_USB11(x) (((x)&(3<<10))==(1<<10))//John Remove	 /* USB 1.1 device */  //FHUSB200 doon't have this function
#else
#define PORT_OWNER	(1<<13)		/* true: companion hc owns this port */  //FHUSB200 doon't have this function
#define PORT_POWER	(1<<12)		/* true: has power (see PPC) */  //FHUSB200 doon't have this function
#define PORT_USB11(x) (((x)&(3<<10))==(1<<10))	 /* USB 1.1 device */  //FHUSB200 doon't have this function
#endif

/* 11:10 for detecting lowspeed devices (reset vs release ownership) */
/* 9 reserved */
#define PORT_RESET	(1<<8)		/* reset port */
#define PORT_SUSPEND	(1<<7)		/* suspend port */
#define PORT_RESUME	(1<<6)		/* resume it */

#ifdef CONFIG_FARADAY_FEHCI//John_Update
//#define PORT_OCC	(1<<5)	//John Remove	/* over current change */  //FHUSB200 doon't have this function
//#define PORT_OC		(1<<4)	//John Remove	/* over current active */  //FHUSB200 doon't have this function
#else
#define PORT_OCC	(1<<5)	/* over current change */  //FHUSB200 doon't have this function
#define PORT_OC		(1<<4)		/* over current active */  //FHUSB200 doon't have this function
#endif

#define PORT_PEC	(1<<3)		/* port enable change */
#define PORT_PE		(1<<2)		/* port enable */
#define PORT_CSC	(1<<1)		/* connect status change */
#define PORT_CONNECT	(1<<0)		/* device connected */

} __attribute__ ((packed));
#if 0
	/* USBINTR: offset 0x08 */
	u32		intr_enable;

	/* FRINDEX: offset 0x0C */
	u32		frame_index;	/* current microframe number */
	/* CTRLDSSEGMENT: offset 0x10 */
	u32		segment; 	/* address bits 63:32 if needed */
	/* PERIODICLISTBASE: offset 0x14 */
	u32		frame_list; 	/* points to periodic list */
	/* ASYNCICLISTADDR: offset 0x18 */
	u32		async_next;	/* address of next async queue head */

	u32		reserved [9];

	/* CONFIGFLAG: offset 0x40 */
	u32		configured_flag;
#define FLAG_CF		(1<<0)		/* true: we'll support "high speed" */

	/* PORTSC: offset 0x44 */
	u32		port_status [0];	/* up to N_PORTS */
/* 31:23 reserved */
#define PORT_WKOC_E	(1<<22)		/* wake on overcurrent (enable) */
#define PORT_WKDISC_E	(1<<21)		/* wake on disconnect (enable) */
#define PORT_WKCONN_E	(1<<20)		/* wake on connect (enable) */
/* 19:16 for port testing */
/* 15:14 for using port indicator leds (if HCS_INDICATOR allows) */
#define PORT_OWNER	(1<<13)		/* true: companion hc owns this port */
#define PORT_POWER	(1<<12)		/* true: has power (see PPC) */
#define PORT_USB11(x) (((x)&(3<<10))==(1<<10))	/* USB 1.1 device */
/* 11:10 for detecting lowspeed devices (reset vs release ownership) */
/* 9 reserved */
#define PORT_RESET	(1<<8)		/* reset port */
#define PORT_SUSPEND	(1<<7)		/* suspend port */
#define PORT_RESUME	(1<<6)		/* resume it */
#define PORT_OCC	(1<<5)		/* over current change */
#define PORT_OC		(1<<4)		/* over current active */
#define PORT_PEC	(1<<3)		/* port enable change */