serial.c

上传linux-jx2410的源代码

	/*
	 * OK, past this point, all the error checking has been done.
	 * At this point, we start making changes.....
	 */

	state->baud_base = new_serial.baud_base;
	state->flags = ((state->flags & ~ASYNC_FLAGS) |
			(new_serial.flags & ASYNC_FLAGS));
	info->flags = ((state->flags & ~ASYNC_INTERNAL_FLAGS) |
		       (info->flags & ASYNC_INTERNAL_FLAGS));
	state->custom_divisor = new_serial.custom_divisor;
	state->close_delay = new_serial.close_delay * HZ/100;
	state->closing_wait = new_serial.closing_wait * HZ/100;
	info->tty->low_latency = (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
	info->xmit_fifo_size = state->xmit_fifo_size =
		new_serial.xmit_fifo_size;

	if ((state->type != PORT_UNKNOWN) && state->port) {
		release_region(state->port,8);
	}
	state->type = new_serial.type;
	if (change_port || change_irq) {
		/*
		 * We need to shutdown the serial port at the old
		 * port/irq combination.
		 */
		shutdown(info);
		state->irq = new_serial.irq;
		info->port = state->port = new_port;
		info->hub6 = state->hub6 = new_serial.hub6;
		if (info->hub6)
			info->io_type = state->io_type = SERIAL_IO_HUB6;
		else if (info->io_type == SERIAL_IO_HUB6)
			info->io_type = state->io_type = SERIAL_IO_PORT;
	}
	if ((state->type != PORT_UNKNOWN) && state->port) {
			request_region(state->port,8,"serial(set)");
	}

	
check_and_exit:
	if (!state->port || !state->type)
		return 0;
	if (info->flags & ASYNC_INITIALIZED) {
		if (((old_state.flags & ASYNC_SPD_MASK) !=
		     (state->flags & ASYNC_SPD_MASK)) ||
		    (old_state.custom_divisor != state->custom_divisor)) {
			if ((state->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
				info->tty->alt_speed = 57600;
			if ((state->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
				info->tty->alt_speed = 115200;
			if ((state->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
				info->tty->alt_speed = 230400;
			if ((state->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
				info->tty->alt_speed = 460800;
			change_speed(info, 0);
		}
	} else {
		retval = startup(info);
	}
	return retval;
}


/*
 * get_lsr_info - get line status register info
 *
 * Purpose: Let user call ioctl() to get info when the UART physically
 * 	    is emptied.  On bus types like RS485, the transmitter must
 * 	    release the bus after transmitting. This must be done when
 * 	    the transmit shift register is empty, not be done when the
 * 	    transmit holding register is empty.  This functionality
 * 	    allows an RS485 driver to be written in user space. 
 */
static int get_lsr_info(struct async_struct * info, unsigned int *value)
{
	unsigned char status;
	unsigned int result;
	unsigned long flags;

	save_flags(flags); cli();
	status = serial_in(info, UART_LSR);
	restore_flags(flags);
	result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);

	/*
	 * If we're about to load something into the transmit
	 * register, we'll pretend the transmitter isn't empty to
	 * avoid a race condition (depending on when the transmit
	 * interrupt happens).
	 */
	if (info->x_char || 
	    ((CIRC_CNT(info->xmit.head, info->xmit.tail,
		       SERIAL_XMIT_SIZE) > 0) &&
	     !info->tty->stopped && !info->tty->hw_stopped))
		result &= TIOCSER_TEMT;

	if (copy_to_user(value, &result, sizeof(int)))
		return -EFAULT;
	return 0;
}


static int get_modem_info(struct async_struct * info, unsigned int *value)
{
	unsigned char control, status;
	unsigned int result;
	unsigned long flags;

	control = info->MCR;
	save_flags(flags); cli();
	status = serial_in(info, UART_MSR);
	restore_flags(flags);
	result =  ((control & UART_MCR_RTS) ? TIOCM_RTS : 0)
		| ((control & UART_MCR_DTR) ? TIOCM_DTR : 0)
#ifdef TIOCM_OUT1
		| ((control & UART_MCR_OUT1) ? TIOCM_OUT1 : 0)
		| ((control & UART_MCR_OUT2) ? TIOCM_OUT2 : 0)
#endif
		| ((status  & UART_MSR_DCD) ? TIOCM_CAR : 0)
		| ((status  & UART_MSR_RI) ? TIOCM_RNG : 0)
		| ((status  & UART_MSR_DSR) ? TIOCM_DSR : 0)
		| ((status  & UART_MSR_CTS) ? TIOCM_CTS : 0);

	if (copy_to_user(value, &result, sizeof(int)))
		return -EFAULT;
	return 0;
}

static int set_modem_info(struct async_struct * info, unsigned int cmd,
			  unsigned int *value)
{
	unsigned int arg;
	unsigned long flags;

	if (copy_from_user(&arg, value, sizeof(int)))
		return -EFAULT;

	switch (cmd) {
	case TIOCMBIS: 
		if (arg & TIOCM_RTS)
			info->MCR |= UART_MCR_RTS;
		if (arg & TIOCM_DTR)
			info->MCR |= UART_MCR_DTR;
#ifdef TIOCM_OUT1
		if (arg & TIOCM_OUT1)
			info->MCR |= UART_MCR_OUT1;
		if (arg & TIOCM_OUT2)
			info->MCR |= UART_MCR_OUT2;
#endif
		if (arg & TIOCM_LOOP)
			info->MCR |= UART_MCR_LOOP;
		break;
	case TIOCMBIC:
		if (arg & TIOCM_RTS)
			info->MCR &= ~UART_MCR_RTS;
		if (arg & TIOCM_DTR)
			info->MCR &= ~UART_MCR_DTR;
#ifdef TIOCM_OUT1
		if (arg & TIOCM_OUT1)
			info->MCR &= ~UART_MCR_OUT1;
		if (arg & TIOCM_OUT2)
			info->MCR &= ~UART_MCR_OUT2;
#endif
		if (arg & TIOCM_LOOP)
			info->MCR &= ~UART_MCR_LOOP;
		break;
	case TIOCMSET:
		info->MCR = ((info->MCR & ~(UART_MCR_RTS |
#ifdef TIOCM_OUT1
					    UART_MCR_OUT1 |
					    UART_MCR_OUT2 |
#endif
					    UART_MCR_LOOP |
					    UART_MCR_DTR))
			     | ((arg & TIOCM_RTS) ? UART_MCR_RTS : 0)
#ifdef TIOCM_OUT1
			     | ((arg & TIOCM_OUT1) ? UART_MCR_OUT1 : 0)
			     | ((arg & TIOCM_OUT2) ? UART_MCR_OUT2 : 0)
#endif
			     | ((arg & TIOCM_LOOP) ? UART_MCR_LOOP : 0)
			     | ((arg & TIOCM_DTR) ? UART_MCR_DTR : 0));
		break;
	default:
		return -EINVAL;
	}
	save_flags(flags); cli();
	info->MCR |= ALPHA_KLUDGE_MCR; 		/* Don't ask */
	serial_out(info, UART_MCR, info->MCR);
	restore_flags(flags);
	return 0;
}

static int do_autoconfig(struct async_struct * info)
{
	int retval;
	
	if (!capable(CAP_SYS_ADMIN))
		return -EPERM;
	
	if (info->state->count > 1)
		return -EBUSY;
	
	shutdown(info);

	autoconfig(info->state);
	retval = startup(info);
	if (retval)
		return retval;
	return 0;
}

/*
 * rs_break() --- routine which turns the break handling on or off
 */
static void rs_break(struct tty_struct *tty, int break_state)
{
	struct async_struct * info = (struct async_struct *)tty->driver_data;
	unsigned long flags;
	
	if (serial_paranoia_check(info, tty->device, "rs_break"))
		return;

	if (!CONFIGURED_SERIAL_PORT(info))
		return;
	save_flags(flags); cli();
	if (break_state == -1)
		info->LCR |= UART_LCR_SBC;
	else
		info->LCR &= ~UART_LCR_SBC;
	serial_out(info, UART_LCR, info->LCR);
	restore_flags(flags);
}


static int rs_ioctl(struct tty_struct *tty, struct file * file,
		    unsigned int cmd, unsigned long arg)
{
	struct async_struct * info = (struct async_struct *)tty->driver_data;
	struct async_icount cprev, cnow;	/* kernel counter temps */
	struct serial_icounter_struct icount;
	unsigned long flags;
	
	if (serial_paranoia_check(info, tty->device, "rs_ioctl"))
		return -ENODEV;

	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
	    (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGSTRUCT) &&
	    (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
		if (tty->flags & (1 << TTY_IO_ERROR))
		    return -EIO;
	}
	
	switch (cmd) {
		case TIOCMGET:
			return get_modem_info(info, (unsigned int *) arg);
		case TIOCMBIS:
		case TIOCMBIC:
		case TIOCMSET:
			return set_modem_info(info, cmd, (unsigned int *) arg);
		case TIOCGSERIAL:
			return get_serial_info(info,
					       (struct serial_struct *) arg);
		case TIOCSSERIAL:
			return set_serial_info(info,
					       (struct serial_struct *) arg);
		case TIOCSERCONFIG:
			return do_autoconfig(info);

		case TIOCSERGETLSR: /* Get line status register */
			return get_lsr_info(info, (unsigned int *) arg);

		case TIOCSERGSTRUCT:
			if (copy_to_user((struct async_struct *) arg,
					 info, sizeof(struct async_struct)))
				return -EFAULT;
			return 0;
				
			
		/*
		 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
		 * - mask passed in arg for lines of interest
 		 *   (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
		 * Caller should use TIOCGICOUNT to see which one it was
		 */
		case TIOCMIWAIT:
			save_flags(flags); cli();
			/* note the counters on entry */
			cprev = info->state->icount;
			restore_flags(flags);
			/* Force modem status interrupts on */
			info->IER |= UART_IER_MSI;
			serial_out(info, UART_IER, info->IER);
			while (1) {
				interruptible_sleep_on(&info->delta_msr_wait);
				/* see if a signal did it */
				if (signal_pending(current))
					return -ERESTARTSYS;
				save_flags(flags); cli();
				cnow = info->state->icount; /* atomic copy */
				restore_flags(flags);
				if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && 
				    cnow.dcd == cprev.dcd && cnow.cts == cprev.cts)
					return -EIO; /* no change => error */
				if ( ((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) ||
				     ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) ||
				     ((arg & TIOCM_CD)  && (cnow.dcd != cprev.dcd)) ||
				     ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts)) ) {
					return 0;
				}
				cprev = cnow;
			}
			/* NOTREACHED */

		/* 
		 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
		 * Return: write counters to the user passed counter struct
		 * NB: both 1->0 and 0->1 transitions are counted except for
		 *     RI where only 0->1 is counted.
		 */
		case TIOCGICOUNT:
			save_flags(flags); cli();
			cnow = info->state->icount;
			restore_flags(flags);
			icount.cts = cnow.cts;
			icount.dsr = cnow.dsr;
			icount.rng = cnow.rng;
			icount.dcd = cnow.dcd;
			icount.rx = cnow.rx;
			icount.tx = cnow.tx;
			icount.frame = cnow.frame;
			icount.overrun = cnow.overrun;
			icount.parity = cnow.parity;
			icount.brk = cnow.brk;
			icount.buf_overrun = cnow.buf_overrun;
			
			if (copy_to_user((void *)arg, &icount, sizeof(icount)))
				return -EFAULT;
			return 0;
		case TIOCSERGWILD:
		case TIOCSERSWILD:
			/* "setserial -W" is called in Debian boot */
			printk ("TIOCSER?WILD ioctl obsolete, ignored.\n");
			return 0;

		default:
			return -ENOIOCTLCMD;
		}
	return 0;
}

static void rs_set_termios(struct tty_struct *tty, struct termios *old_termios)
{
	struct async_struct *info = (struct async_struct *)tty->driver_data;
	unsigned long flags;
	unsigned int cflag = tty->termios->c_cflag;
	
	if (   (cflag == old_termios->c_cflag)
	    && (   RELEVANT_IFLAG(tty->termios->c_iflag) 
		== RELEVANT_IFLAG(old_termios->c_iflag)))
	  return;

	change_speed(info, old_termios);

	/* Handle transition to B0 status */
	if ((old_termios->c_cflag & CBAUD) &&
	    !(cflag & CBAUD)) {
		info->MCR &= ~(UART_MCR_DTR|UART_MCR_RTS);
		save_flags(flags); cli();
		serial_out(info, UART_MCR, info->MCR);
		restore_flags(flags);
	}
	
	/* Handle transition away from B0 status */
	if (!(old_termios->c_cflag & CBAUD) &&
	    (cflag & CBAUD)) {
		info->MCR |= UART_MCR_DTR;
		if (!(tty->termios->c_cflag & CRTSCTS) || 
		    !test_bit(TTY_THROTTLED, &tty->flags)) {
			info->MCR |= UART_MCR_RTS;
		}
		save_flags(flags); cli();
		serial_out(info, UART_MCR, info->MCR);
		restore_flags(flags);
	}
	
	/* Handle turning off CRTSCTS */
	if ((old_termios->c_cflag & CRTSCTS) &&
	    !(tty->termios->c_cflag & CRTSCTS)) {
		tty->hw_stopped = 0;
		rs_start(tty);
	}
}

/*
 * ------------------------------------------------------------
 * rs_close()
 * 
 * This routine is called when the serial port gets closed.  First, we
 * wait for the last remaining data to be sent.  Then, we unlink its
 * async structure from the interrupt chain if necessary, and we free
 * that IRQ if nothing is left in the chain.
 * ------------------------------------------------------------
 */
static void rs_close(struct tty_struct *tty, struct file * filp)
{
	struct async_struct * info = (struct async_struct *)tty->driver_data;
	struct serial_state *state;
	unsigned long flags;

	if (!info || serial_paranoia_check(info, tty->device, "rs_close"))
		return;

	state = info->state;
	
	save_flags(flags); cli();
	
	if (tty_hung_up_p(filp)) {
		DBG_CNT("before DEC-hung");
		MOD_DEC_USE_COUNT;
		restore_flags(flags);
		return;
	}
	
#ifdef SERIAL_DEBUG_OPEN
	printk("rs_close ttys%d, count = %d\n", info->line, state->count);
#endif
	if ((tty->count == 1) && (state->count != 1)) {
		/*
		 * Uh, oh.  tty->count is 1, which means that the tty
		 * structure will be freed.  state->count should always
		 * be one in these conditions.  If it's greater than
		 * one, we've got real problems, since it means the
		 * serial port won't be shutdown.
		 */
		printk("rs_close: bad serial port count; tty->count is 1, "
		       "state->count is %d\n", state->count);
		state->count = 1;
	}
	if (--state->count < 0) {
		printk("rs_close: bad serial port count for ttys%d: %d\n",
		       info->line, state->count);
		state->count = 0;
	}
	if (state->count) {
		DBG_CNT("before DEC-2");
		MOD_DEC_USE_COUNT;
		restore_flags(flags);
		return;
	}
	info->flags |= ASYNC_CLOSING;
	restore_flags(flags);
	/*
	 * Save the termios structure, since this port may have
	 * separate termios for callout and dialin.
	 */
	if (info->flags & ASYNC_NORMAL_ACTIVE)
		info->state->normal_termios = *tty->termios;
	if (info->flags & ASYNC_CALLOUT_ACTIVE)
		info->state->callout_termios = *tty->termios;
	/*
	 * Now we wait for the transmit buffer to clear; and we notify 
	 * the line discipline to only process XON/XOFF characters.
	 */
	tty->closing = 1;
	if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE)
		tty_wait_until_sent(tty, info->closing_wait);
	/*
	 * At this point we stop accepting input.  To do this, we
	 * disable the receive line status interrupts, and tell the
	 * interrupt driver to stop checking the data ready bit in the
	 * line status register.
	 */
	info->IER &= ~UART_IER_RLSI;
	info->read_status_mask &= ~UART_LSR_DR;
	if (info->flags & ASYNC_INITIALIZED) {
		serial_out(info, UART_IER, info->IER);
		/*
		 * Before we drop DTR, make sure the UART transmitter
		 * has completely drained; this is especially
		 * important if there is a transmit FIFO!
		 */
		rs_wait_until_sent(tty, info->timeout);
	}
	shutdown(info);
	if (tty->driver.flush_buffer)
		tty->driver.flush_buffer(tty);
	if (tty->ldisc.flush_buffer)
		tty->ldisc.flush_buffer(tty);
	tty->closing = 0;
	info->event = 0;
	info->tty = 0;
	if (info->blocked_open) {