hplatm128i2cbusp.nc

tinyos2.0版本驱动

/// $Id: HplAtm128I2CBusP.nc,v 1.1 2008/06/12 14:02:12 klueska Exp $

/*
 *  Copyright (c) 2004-2005 Crossbow Technology, Inc.
 *  All rights reserved.
 *
 *  Permission to use, copy, modify, and distribute this software and its
 *  documentation for any purpose, without fee, and without written
 *  agreement is hereby granted, provided that the above copyright
 *  notice, the (updated) modification history and the author appear in
 *  all copies of this source code.
 *
 *  Permission is also granted to distribute this software under the
 *  standard BSD license as contained in the TinyOS distribution.
 *
 *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS `AS IS'
 *  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 
 *  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 *  ARE DISCLAIMED.  IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS 
 *  BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 
 *  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF USE, DATA, 
 *  OR PROFITS) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 
 *  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 
 *  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 
 *  THE POSSIBILITY OF SUCH DAMAGE.
 */

#define F_CPU       7372800

#include "Atm128I2C.h"

/**
 * This driver implements direct I2C register access and a blocking master
 * controller for the ATmega128 via a Hardware Platform Layer (HPL) to its  
 * two-wire-interface (TWI) hardware subsystem.
 *
 * @author Martin Turon <[e-mail]>
 * @author Philip Levis
 *
 * @version $Id: HplAtm128I2CBusP.nc,v 1.1 2008/06/12 14:02:12 klueska Exp $
 */
module HplAtm128I2CBusP {
  provides interface HplAtm128I2CBus as I2C;

  uses {
    interface GeneralIO as I2CClk;
    interface GeneralIO as I2CData;
    interface PlatformInterrupt;
  }
}
implementation {
  uint8_t current;
  
  async command void I2C.init(bool hasExternalPulldown) {
    // Set the internal pullup resisters
    if (hasExternalPulldown) {
      //call I2CClk.makeOutput();
      //call I2CData.makeOutput();
      call I2CClk.set();
      call I2CData.set();
    }
    call I2CClk.makeInput();
    call I2CData.makeInput();
    TWSR = 0;                             // set prescaler == 0
    TWBR = (F_CPU / 50000UL - 16) / 2;   // set I2C baud rate
    //TWBR = 50;
    TWAR = 0;
    TWCR = 0;
  }

  async command void I2C.off() {
    call I2CClk.clr();
    call I2CData.clr();
  }
  
  async command uint8_t I2C.status() {
    return TWSR & 0xf8;
  }

  async command void I2C.sendCommand() {
    atomic TWCR = current;
  }

  async command void I2C.readCurrent() {
    atomic current = TWCR;
  }
  
  /** Send START symbol and begin I2C bus transaction. */
  async command void I2C.setStart(bool on) {
    if (on) {
      atomic SET_BIT(current, TWSTA);
    }
    else {
      atomic CLR_BIT(current, TWSTA);
    }
  }
  async command bool I2C.hasStart() {
    return READ_BIT(current, TWSTA);
  }

  async command void I2C.setStop(bool on) {
    if (on) {
      atomic SET_BIT(current, TWSTO);
    }
    else {
      atomic CLR_BIT(current, TWSTO);
    }
  }
  async command bool I2C.hasStop() {
    return READ_BIT(current, TWSTO);
  }
  
  /** Write a byte to an I2C slave device. */
  async command void I2C.write(uint8_t data) {
    TWDR = data;
  }

  async command uint8_t I2C.read() {
    return TWDR;
  }

  async command void I2C.enableAck(bool enable) {
    if (enable) {
      atomic SET_BIT(current, TWEA);
    }
    else {
      atomic CLR_BIT(current, TWEA);
    }
  }
  
  async command bool I2C.hasAcks() {
    return READ_BIT(current, TWEA);
  }
  
  async command void I2C.enableInterrupt(bool enable) {
    if (enable) {
      atomic SET_BIT(current, TWIE);
    }
    else {
      atomic CLR_BIT(current, TWIE);
    }
  }

  async command bool I2C.isInterruptEnabled() {
    return READ_BIT(current, TWIE);
  }
  
  async command bool I2C.isRealInterruptPending() {
    return READ_BIT(TWCR, TWINT);
  }

  async command bool I2C.isInterruptPending() {
    return READ_BIT(current, TWINT);
  }

  async command void I2C.setInterruptPending(bool on) {
    if (on) {
      atomic SET_BIT(current, TWINT);
    }
    else {
      atomic CLR_BIT(current, TWINT);
    }
  }
  
  async command void I2C.enable(bool enable) {
    if (enable) {
      atomic SET_BIT(current, TWEN);
    }
    else {
      atomic CLR_BIT(current, TWEN);
    }
  }

  async command bool I2C.isEnabled() {
    return READ_BIT(current, TWEN);
  }

  async command bool I2C.hasWriteCollided() {
    return READ_BIT(current, TWWC);
  }

  default async event void I2C.commandComplete() { }
  AVR_ATOMIC_HANDLER(SIG_2WIRE_SERIAL) {
    signal I2C.commandComplete();
    call PlatformInterrupt.postAmble();
  }
}