add_2bit_module_map.mrp

该源码为xilinx ise教程的附带光盘源码

Release 9.1i Map J.30
Xilinx Mapping Report File for Design 'add_2bit_module'

Design Information
------------------
Command Line   : D:\Xilinx91i\bin\nt\map.exe -ise
D:/ise_book/Example-8-2/test_add/test_add.ise -intstyle ise -p xcv50e-cs144-6
-cm area -pr b -k 4 -c 100 -tx off -o add_2bit_module_map.ncd
add_2bit_module.ngd add_2bit_module.pcf 
Target Device  : xcv50e
Target Package : cs144
Target Speed   : -6
Mapper Version : virtexe -- $Revision: 1.36 $
Mapped Date    : Wed Dec 27 17:39:47 2006

Design Summary
--------------
Number of errors:      0
Number of warnings:    2
Logic Utilization:
Logic Distribution:
    Number of Slices containing only related logic:      0 out of      0    0%
    Number of Slices containing unrelated logic:         0 out of      0    0%
        *See NOTES below for an explanation of the effects of unrelated logic
   Number of bonded IOBs:             8 out of     94    8%

   Number of hard macros:           1
Total equivalent gate count for design (not including hard macros):  0
Additional JTAG gate count for IOBs:  384
Peak Memory Usage:  140 MB
Total REAL time to MAP completion:  4 secs 
Total CPU time to MAP completion:   3 secs 

NOTES:

   Related logic is defined as being logic that shares connectivity - e.g. two
   LUTs are "related" if they share common inputs.  When assembling slices,
   Map gives priority to combine logic that is related.  Doing so results in
   the best timing performance.

   Unrelated logic shares no connectivity.  Map will only begin packing
   unrelated logic into a slice once 99% of the slices are occupied through
   related logic packing.

   Note that once logic distribution reaches the 99% level through related
   logic packing, this does not mean the device is completely utilized.
   Unrelated logic packing will then begin, continuing until all usable LUTs
   and FFs are occupied.  Depending on your timing budget, increased levels of
   unrelated logic packing may adversely affect the overall timing performance
   of your design.

Table of Contents
-----------------
Section 1 - Errors
Section 2 - Warnings
Section 3 - Informational
Section 4 - Removed Logic Summary
Section 5 - Removed Logic
Section 6 - IOB Properties
Section 7 - RPMs
Section 8 - Guide Report
Section 9 - Area Group and Partition Summary
Section 10 - Modular Design Summary
Section 11 - Timing Report
Section 12 - Configuration String Information

Section 1 - Errors
------------------

Section 2 - Warnings
--------------------
WARNING:LIT:243 - Logical network N4 has no load.
WARNING:LIT:395 - The above warning message base_net_load_rule is repeated 1
   more times for the following (max. 5 shown):
   N5
   To see the details of these warning messages, please use the -detail switch.

Section 3 - Informational
-------------------------
INFO:MapLib:562 - No environment variables are currently set.
INFO:LIT:244 - All of the single ended outputs in this design are using slew
   rate limited output drivers. The delay on speed critical single ended outputs
   can be dramatically reduced by designating them as fast outputs in the
   schematic.

Section 4 - Removed Logic Summary
---------------------------------
   2 block(s) removed
   2 signal(s) removed

Section 5 - Removed Logic
-------------------------

The trimmed logic report below shows the logic removed from your design due to
sourceless or loadless signals, and VCC or ground connections.  If the removal
of a signal or symbol results in the subsequent removal of an additional signal
or symbol, the message explaining that second removal will be indented.  This
indentation will be repeated as a chain of related logic is removed.

To quickly locate the original cause for the removal of a chain of logic, look
above the place where that logic is listed in the trimming report, then locate
the lines that are least indented (begin at the leftmost edge).

The signal "N4" is loadless and has been removed.
 Loadless block "XST_GND" (ZERO) removed.
The signal "N5" is loadless and has been removed.
 Loadless block "XST_VCC" (ONE) removed.

Section 6 - IOB Properties
--------------------------

+------------------------------------------------------------------------------------------------------------------------+
| IOB Name                           | Type    | Direction | IO Standard | Drive    | Slew | Reg (s)  | Resistor | IOB   |
|                                    |         |           |             | Strength | Rate |          |          | Delay |
+------------------------------------------------------------------------------------------------------------------------+
| a<0>                               | IOB     | INPUT     | LVTTL       |          |      |          |          |       |
| a<1>                               | IOB     | INPUT     | LVTTL       |          |      |          |          |       |
| b<0>                               | IOB     | INPUT     | LVTTL       |          |      |          |          |       |
| b<1>                               | IOB     | INPUT     | LVTTL       |          |      |          |          |       |
| c<0>                               | IOB     | OUTPUT    | LVTTL       | 12       | SLOW |          |          |       |
| c<1>                               | IOB     | OUTPUT    | LVTTL       | 12       | SLOW |          |          |       |
| cin                                | IOB     | INPUT     | LVTTL       |          |      |          |          |       |
| cout                               | IOB     | OUTPUT    | LVTTL       | 12       | SLOW |          |          |       |
+------------------------------------------------------------------------------------------------------------------------+

Section 7 - RPMs
----------------

Section 8 - Guide Report
------------------------
Guide not run on this design.

Section 9 - Area Group and Partition Summary
--------------------------------------------

Partition Implementation Status
-------------------------------

  No Partitions were found in this design.

-------------------------------

Area Group Information
----------------------

  No area groups were found in this design.

----------------------

Section 10 - Modular Design Summary
-----------------------------------
Modular Design not used for this design.

Section 11 - Timing Report
--------------------------
No timing report for this architecture.

Section 12 - Configuration String Details
-----------------------------------------
Use the "-detail" map option to print out Configuration Strings