dp80390xp.h

Keil uVision2

/*--------------------------------------------------------------------------
  DP80390XP.H
 Registers definition for DCD DP80390XP

 Copyright (c) 2003 Keil Elektronik GmbH and Keil Software, Inc.
 All rights reserved.
-------------------------------------------------------------------------- */
#ifndef _DP80390XP_H_
#define _DP80390XP_H_

/* ----------------------------------------------------------------------- */
/* ----------------------------------------------------------------------- */
/* Defined configuration peripherals */

  #define PMU_ENABLED      /* Power Management Unit enabled */
  #define DPTR1_ENABLED    /* Enable second DPTR1           */

  #define PORT0_ENABLED    /* Port 0 enabled                */
  #define PORT1_ENABLED    /* Port 1 enabled                */
  #define PORT2_ENABLED    /* Port 2 enabled                */
  #define PORT3_ENABLED    /* Port 3 enabled                */

  #define TIMERS01_ENABLED /* Timers 0&1 enabled            */
  #define TIMER2_ENABLED   /* Timer 2 enabled               */
  #define CC_ENABLED       /* Compare/Capture enabled       */

  #define UART0_ENABLED    /* UART 0 enabled                */
  #define UART1_ENABLED    /* UART 1 enabled                */

  #define MDU_ENABLED      /* 16/32-bit MUL/DIV enabled     */

  #define DI2CM_ENABLED    /* Master I2C enabled            */
  #define DI2CS_ENABLED    /* Slave I2C enabled             */
  #define WATCHDOG_ENABLED /* Watchdog enabled              */
  #define DSPI_ENABLED     /* Master/Slave SPI enabled      */

/* *********************************************************************** */
/* *********************************************************************** */

/*---------------------------------------------------------------------------
  Defined registers  
---------------------------------------------------------------------------*/

/*  BYTE Register  */
#ifdef PORT0_ENABLED
  sfr P0        = 0x80; /* Port 0                    */
#endif

sfr SP        = 0x81;
sfr DPL       = 0x82;   /* Data Pointer 0 Low byte   */
sfr DPL0      = 0x82;
sfr DPH       = 0x83;   /* Data Pointer 0 Hgih byte  */
sfr DPH0      = 0x83;

#ifdef DPTR1_ENABLED
  sfr DPL1      = 0x84; /* Data Pointer 1 Low byte   */
  sfr DPH1      = 0x85; /* Data Pointer 1 High byte  */
  sfr DPS       = 0x86; /* Data pointers select      */
#endif

sfr PCON      = 0x87;   /* Power Configuration       */
sfr TCON      = 0x88;   /* Timer 0,1 Configuration   */

#ifdef TIMERS01_ENABLED
  sfr TMOD      = 0x89; /* Timer 0,1 Mode            */
  sfr TL0       = 0x8A; /* Timer 0 Low byte counter  */
  sfr TL1       = 0x8B; /* Timer 1 Low byte counter  */
  sfr TH0       = 0x8C; /* Timer 0 High byte counter */
  sfr TH1       = 0x8D; /* Timer 1 High byte counter */
#endif

sfr CKCON     = 0x8E;   /* XDATA Wait States         */
/* 0x8F */
#ifdef PORT1_ENABLED
  sfr P1        = 0x90; /* Port 1                    */
#endif

sfr EIF       = 0x91;   /* External Interrupt Flag   */

sfr WTST      = 0x92;   /* Program Wait States       */

sfr DPP       = 0x93;   /* Data Page Pointer 0       */
sfr DPX0      = 0x93;
/* 0x94 */
#ifdef DPTR1_ENABLED
  sfr DPX1      = 0x95; /* Data Page Pointer 1       */
#endif
/* 0x96
   0x97*/
#ifdef UART0_ENABLED
  sfr SCON      = 0x98; /* Serial 0 Configuration    */
  sfr SCON0     = 0x98;
  sfr SBUF      = 0x99; /* Serial 0 I/O Buffer       */
  sfr SBUF0     = 0x99;
#endif
/* 0x9A
   0x9B
   0x9C*/
  sfr ACON      = 0x9D; /* Address Control FLAT/LARGE*/
/* 0x9E
   0x9F*/
#ifdef PORT2_ENABLED
  sfr P2        = 0xA0; /* Port 2                    */
#endif
/* 0xA1
   0xA2
   0xA3
   0xA4
   0xA5
   0xA6
   0xA7*/
sfr IE        = 0xA8;   /* Interrupt Enable          */
/* 0xA9
   0xAA
   0xAB
   0xAC
   0xAD
   0xAE
   0xAF*/
#ifdef PORT3_ENABLED
  sfr P3        = 0xB0; /* Port 3                    */
#endif
/* 0xB1
   0xB2
   0xB3
   0xB4
   0xB5
   0xB6
   0xB7*/
sfr IP        = 0xB8;
/* 0xB9
   0xBA
   0xBB
   0xBC
   0xBD
   0xBE
   0xBF*/

#ifdef UART1_ENABLED
  sfr SCON1     = 0xC0; /* Serial 1 Configuration    */
  sfr SBUF1     = 0xC1; /* Serial 1 I/O Buffer       */
#endif

#ifdef CC_ENABLED
  sfr CCL1     = 0xC2;  /* Comare/Capture/Reload 1 Low */
  sfr CCH1     = 0xC3;  /* Comare/Capture/Reload 1 High*/
  sfr CCL2     = 0xC4;  /* Comare/Capture/Reload 2 Low */
  sfr CCH2     = 0xC5;  /* Comare/Capture/Reload 2 High*/
  sfr CCL3     = 0xC6;  /* Comare/Capture/Reload 3 Low */
  sfr CCH3     = 0xC7;  /* Comare/Capture/Reload 3 High*/
#endif

#if defined(TIMER2_ENABLED)  || defined(CC_ENABLED)
  sfr T2CON     = 0xC8; /* Timer 2 Configuration     */
#endif

#ifdef CC_ENABLED
  sfr T2IF      = 0xC9; /* Timer 2 Interrupt Flags   */
  sfr RCRL      = 0xCA; /* Timer 2 Reload Low byte   */
  sfr RCRH      = 0xCB; /* Timer 2 Reload High byte  */
  sfr TL2       = 0xCC; /* Timer 2 Low byte counter  */
  sfr TH2       = 0xCD; /* Timer 2 High byte counter */
#else
  #ifdef TIMER2_ENABLED
    sfr RLDL      = 0xCA; /* Timer 2 Reload Low byte   */
    sfr RLDH      = 0xCB; /* Timer 2 Reload High byte  */
    sfr TL2       = 0xCC; /* Timer 2 Low byte counter  */
    sfr TH2       = 0xCD; /* Timer 2 High byte counter */
  #endif
#endif

#ifdef CC_ENABLED
  sfr CCEN      = 0xCE; /* Comare/Capture/Reload Enable*/
#endif
/* 0xCF */
sfr PSW       = 0xD0;   /* Program Status Word       */
/* 0xD1
   0xD2
   0xD3
   0xD4
   0xD5
   0xD6
   0xD7*/
#ifdef WATCHDOG_ENABLED
  sfr WDCON     = 0xD8; /* Watchdog configuration    */
#endif
/* 0xD9
   0xDA
   0xDB
   0xDC
   0xDD
   0xDE
   0xDF*/
sfr ACC       = 0xE0;   /* Accumulator               */
/* 0xE1
   0xE2
   0xE3
   0xE4
   0xE5
   0xE6
   0xE7*/
sfr EIE       = 0xE8;   /* External Interrupt Enable */

#ifdef PMU_ENABLED
  sfr STATUS    = 0xE9; /* Status register           */
#endif

sfr MXAX      = 0xEA;   /* MOVX @Ri High address     */

#ifdef WATCHDOG_ENABLED
  sfr TA        = 0xEB; /* Timed Access protection   */
#endif

#ifdef DSPI_ENABLED
  sfr SPCR      = 0xEC; /* SPI Control Register      */
  sfr SPSR      = 0xED; /* SPI Status Register       */
  sfr SPDR      = 0xEE; /* SPI I/O Register          */
  sfr SSCR      = 0xEF; /* SPI Sleve Select Register */
#endif

sfr B         = 0xF0;   /* B Working register        */

#ifdef DI2CS_ENABLED
  sfr I2CSADR = 0xF1;   /* I2CS Address              */
  sfr I2CSCR  = 0xF2;   /* I2CS Control Register     */
  sfr I2CSBUF = 0xF3;   /* I2CS I/O Buffer           */
#endif

#ifdef DI2CM_ENABLED
  sfr I2CMSA   = 0xF4;  /* I2CM Slave Address        */
  sfr I2CMCR   = 0xF5;  /* I2CM Control Register     */
  sfr I2CMBUF  = 0xF6;  /* I2CM I/O Buffer           */
  sfr I2CMTP   = 0xF7;  /* I2CM Timer Period         */
#endif

sfr EIP       = 0xF8;   /* External Interr. Priority */

#ifdef MDU_ENABLED
  sfr MD0       = 0xF9; /* MDU Data 0                */
  sfr MD1       = 0xFA; /* MDU Data 1                */
  sfr MD2       = 0xFB; /* MDU Data 2                */
  sfr MD3       = 0xFC; /* MDU Data 3                */
  sfr MD4       = 0xFD; /* MDU Data 4                */
  sfr MD5       = 0xFE; /* MDU Data 5                */
  sfr ARCON     = 0xFF; /* MDU Control               */
#endif


/*-------------------------------------------------------------------------
  BIT Register  
  -------------------------------------------------------------------------*/

/*  P0  */
#ifdef PORT0_ENABLED
  sbit P0_7     = P0^7;
  sbit P0_6     = P0^6;
  sbit P0_5     = P0^5;
  sbit P0_4     = P0^4;
  sbit P0_3     = P0^3;
  sbit P0_2     = P0^2;
  sbit P0_1     = P0^1;
  sbit P0_0     = P0^0;
#endif
/*  P1  */
#ifdef PORT1_ENABLED
  sbit P1_7     = P1^7;
  sbit P1_6     = P1^6;
  sbit P1_5     = P1^5;
  sbit P1_4     = P1^4;
  sbit P1_3     = P1^3;
  sbit P1_2     = P1^2;
  sbit P1_1     = P1^1;
  sbit P1_0     = P1^0;
#endif
/*  P2  */
#ifdef PORT2_ENABLED
  sbit P2_7     = P2^7;
  sbit P2_6     = P2^6;
  sbit P2_5     = P2^5;
  sbit P2_4     = P2^4;
  sbit P2_3     = P2^3;
  sbit P2_2     = P2^2;
  sbit P2_1     = P2^1;
  sbit P2_0     = P2^0;
#endif
/*  P3  */
#ifdef PORT3_ENABLED
  sbit P3_7     = P3^7;
  sbit P3_6     = P3^6;
  sbit P3_5     = P3^5;
  sbit P3_4     = P3^4;
  sbit P3_3     = P3^3;
  sbit P3_2     = P3^2;
  sbit P3_1     = P3^1;
  sbit P3_0     = P3^0;
#endif
/*  TCON  */
sbit IT0      = TCON^0;
sbit IE0      = TCON^1;
sbit IT1      = TCON^2;
sbit IE1      = TCON^3;
#ifdef TIMERS01_ENABLED
  sbit TR0      = TCON^4;
  sbit TF0      = TCON^5;
  sbit TR1      = TCON^6;
  sbit TF1      = TCON^7;
#endif

/*  SCON0 */
#ifdef UART0_ENABLED
  sbit RI0      = SCON0^0;
  sbit TI0      = SCON0^1;
  sbit RB08     = SCON0^2;
  sbit TB08     = SCON0^3;
  sbit REN0     = SCON0^4;
  sbit SM02     = SCON0^5;
  sbit SM01     = SCON0^6;
  sbit SM00     = SCON0^7;
  
  /* SCON */
  sbit RI       = SCON0^0;
  sbit TI       = SCON0^1;
  sbit RB8      = SCON0^2;
  sbit TB8      = SCON0^3;
  sbit REN      = SCON0^4;
  sbit SM2      = SCON0^5;