usb100.h

USB程序设计,在Keil工程下编译通过,程序模块清晰,相信对USB程序设计者会有帮助.

typedef unsigned char UCHAR;
typedef unsigned short USHORT;

#define MAXIMUM_USB_STRING_LENGTH 255

// values for the bits returned by the USB GET_STATUS command
#define USB_GETSTATUS_SELF_POWERED                0x01
#define USB_GETSTATUS_REMOTE_WAKEUP_ENABLED       0x02


#define USB_DEVICE_DESCRIPTOR_TYPE                0x01
#define USB_CONFIGURATION_DESCRIPTOR_TYPE         0x02
#define USB_STRING_DESCRIPTOR_TYPE                0x03
#define USB_INTERFACE_DESCRIPTOR_TYPE             0x04
#define USB_ENDPOINT_DESCRIPTOR_TYPE              0x05
#define USB_POWER_DESCRIPTOR_TYPE                 0x06

#define USB_DESCRIPTOR_MAKE_TYPE_AND_INDEX(d, i) ((USHORT)((USHORT)d<<8 | i))

//
// Values for bmAttributes field of an
// endpoint descriptor
//

#define USB_ENDPOINT_TYPE_MASK                    0x03

#define USB_ENDPOINT_TYPE_CONTROL                 0x00
#define USB_ENDPOINT_TYPE_ISOCHRONOUS             0x01
#define USB_ENDPOINT_TYPE_BULK                    0x02
#define USB_ENDPOINT_TYPE_INTERRUPT               0x03


//
// definitions for bits in the bmAttributes field of a 
// configuration descriptor.
//
#define USB_CONFIG_POWERED_MASK                   0xc0

#define USB_CONFIG_BUS_POWERED                    0x80
#define USB_CONFIG_SELF_POWERED                   0x40
#define USB_CONFIG_REMOTE_WAKEUP                  0x20

//
// Endpoint direction bit, stored in address
//

#define USB_ENDPOINT_DIRECTION_MASK               0x80

// test direction bit in the bEndpointAddress field of
// an endpoint descriptor.
#define USB_ENDPOINT_DIRECTION_OUT(addr)          (!((addr) & USB_ENDPOINT_DIRECTION_MASK))
#define USB_ENDPOINT_DIRECTION_IN(addr)           ((addr) & USB_ENDPOINT_DIRECTION_MASK)

//
// USB defined request codes
// see chapter 9 of the USB 1.0 specifcation for
// more information.
//

// These are the correct values based on the USB 1.0
// specification

#define USB_REQUEST_GET_STATUS                    0x00
#define USB_REQUEST_CLEAR_FEATURE                 0x01

#define USB_REQUEST_SET_FEATURE                   0x03

#define USB_REQUEST_SET_ADDRESS                   0x05
#define USB_REQUEST_GET_DESCRIPTOR                0x06
#define USB_REQUEST_SET_DESCRIPTOR                0x07
#define USB_REQUEST_GET_CONFIGURATION             0x08
#define USB_REQUEST_SET_CONFIGURATION             0x09
#define USB_REQUEST_GET_INTERFACE                 0x0A
#define USB_REQUEST_SET_INTERFACE                 0x0B
#define USB_REQUEST_SYNC_FRAME                    0x0C


//
// defined USB device classes
//


#define USB_DEVICE_CLASS_RESERVED           0x00
#define USB_DEVICE_CLASS_AUDIO              0x01
#define USB_DEVICE_CLASS_COMMUNICATIONS     0x02
#define USB_DEVICE_CLASS_HUMAN_INTERFACE    0x03
#define USB_DEVICE_CLASS_MONITOR            0x04
#define USB_DEVICE_CLASS_PHYSICAL_INTERFACE 0x05
#define USB_DEVICE_CLASS_POWER              0x06
#define USB_DEVICE_CLASS_PRINTER            0x07
#define USB_DEVICE_CLASS_STORAGE            0x08
#define USB_DEVICE_CLASS_HUB                0x09
#define USB_DEVICE_CLASS_VENDOR_SPECIFIC    0xFF

//
// USB defined Feature selectors
//

#define USB_FEATURE_ENDPOINT_STALL          0x0000
#define USB_FEATURE_REMOTE_WAKEUP           0x0001
#define USB_FEATURE_POWER_D0                0x0002
#define USB_FEATURE_POWER_D1                0x0003
#define USB_FEATURE_POWER_D2                0x0004
#define USB_FEATURE_POWER_D3                0x0005

typedef struct _USB_DEVICE_DESCRIPTOR {
    UCHAR bLength;
    UCHAR bDescriptorType;
    USHORT bcdUSB;
    UCHAR bDeviceClass;
    UCHAR bDeviceSubClass;
    UCHAR bDeviceProtocol;
    UCHAR bMaxPacketSize0;
    USHORT idVendor;
    USHORT idProduct;
    USHORT bcdDevice;
    UCHAR iManufacturer;
    UCHAR iProduct;
    UCHAR iSerialNumber;
    UCHAR bNumConfigurations;
} USB_DEVICE_DESCRIPTOR;

typedef struct _USB_ENDPOINT_DESCRIPTOR {
    UCHAR bLength;
    UCHAR bDescriptorType;
    UCHAR bEndpointAddress;
    UCHAR bmAttributes;
    USHORT wMaxPacketSize;
    UCHAR bInterval;
} USB_ENDPOINT_DESCRIPTOR;

//
// values for bmAttributes Field in
// USB_CONFIGURATION_DESCRIPTOR
//

#define BUS_POWERED                           0x80
#define SELF_POWERED                          0x40
#define REMOTE_WAKEUP                         0x20

typedef struct _USB_CONFIGURATION_DESCRIPTOR {
    UCHAR bLength;
    UCHAR bDescriptorType;
    USHORT wTotalLength;
    UCHAR bNumInterfaces;
    UCHAR bConfigurationValue;
    UCHAR iConfiguration;
    UCHAR bmAttributes;
    UCHAR MaxPower;
} USB_CONFIGURATION_DESCRIPTOR;

typedef struct _USB_INTERFACE_DESCRIPTOR {
    UCHAR bLength;
    UCHAR bDescriptorType;
    UCHAR bInterfaceNumber;
    UCHAR bAlternateSetting;
    UCHAR bNumEndpoints;
    UCHAR bInterfaceClass;
    UCHAR bInterfaceSubClass;
    UCHAR bInterfaceProtocol;
    UCHAR iInterface;
} USB_INTERFACE_DESCRIPTOR;

typedef struct _USB_STRING_DESCRIPTOR {
    UCHAR bLength;
    UCHAR bDescriptorType;
    UCHAR bString[1];
} USB_STRING_DESCRIPTOR;

//
// USB power descriptor added to core specification
//

#define USB_SUPPORT_D0_COMMAND      0x01
#define USB_SUPPORT_D1_COMMAND      0x02
#define USB_SUPPORT_D2_COMMAND      0x04
#define USB_SUPPORT_D3_COMMAND      0x08

#define USB_SUPPORT_D1_WAKEUP       0x10
#define USB_SUPPORT_D2_WAKEUP       0x20


typedef struct _USB_POWER_DESCRIPTOR {
    UCHAR bLength;
    UCHAR bDescriptorType;
    UCHAR bCapabilitiesFlags;
    USHORT EventNotification;
    USHORT D1LatencyTime;
    USHORT D2LatencyTime;
    USHORT D3LatencyTime;
    UCHAR PowerUnit;
    USHORT D0PowerConsumption;
    USHORT D1PowerConsumption;
    USHORT D2PowerConsumption;
} USB_POWER_DESCRIPTOR;


typedef struct _USB_COMMON_DESCRIPTOR {
    UCHAR bLength;
    UCHAR bDescriptorType;
} USB_COMMON_DESCRIPTOR;


//
// Standard USB HUB definitions 
//
// See Chapter 11
//

typedef struct _USB_HUB_DESCRIPTOR {
    UCHAR        bDescriptorLength;      // Length of this descriptor
    UCHAR        bDescriptorType;        // Hub configuration type
    UCHAR        bNumberOfPorts;         // number of ports on this hub
    USHORT       wHubCharacteristics;    // Hub Charateristics
    UCHAR        bPowerOnToPowerGood;    // port power on till power good in 2ms
    UCHAR        bHubControlCurrent;     // max current in mA
    //
    // room for 255 ports power control and removable bitmask
    UCHAR        bRemoveAndPowerMask[64];
} USB_HUB_DESCRIPTOR;


#define NUM_ENDPOINTS	   4
#define USB_CLASS_CODE_TEST_CLASS_DEVICE                    0xdc
#define USB_SUBCLASS_CODE_TEST_CLASS_D12                    0xA0
#define USB_PROTOCOL_CODE_TEST_CLASS_D12                    0xB0
#define CONFIG_DESCRIPTOR_LENGTH    (sizeof(USB_CONFIGURATION_DESCRIPTOR) + sizeof(USB_INTERFACE_DESCRIPTOR) + (NUM_ENDPOINTS * sizeof(USB_ENDPOINT_DESCRIPTOR)))


//设备描述符
code USB_DEVICE_DESCRIPTOR DeviceDescr =
{
	sizeof(USB_DEVICE_DESCRIPTOR),
    USB_DEVICE_DESCRIPTOR_TYPE,
    SWAP(0x0100),
    USB_CLASS_CODE_TEST_CLASS_DEVICE,
    0, 0,
	EP0_PACKET_SIZE,
	SWAP(0x0471),
	SWAP(0x0666),
	SWAP(0x0100),
    0, 0, 0,
	25
};

//配置描述符
code USB_CONFIGURATION_DESCRIPTOR ConfigDescr =
{
    sizeof(USB_CONFIGURATION_DESCRIPTOR),
    USB_CONFIGURATION_DESCRIPTOR_TYPE,
    SWAP(CONFIG_DESCRIPTOR_LENGTH),
	1,
	1,
    0,
	0x60,
	0x1
};

//接口描述符
code USB_INTERFACE_DESCRIPTOR InterfaceDescr =
{
    sizeof(USB_INTERFACE_DESCRIPTOR),
    USB_INTERFACE_DESCRIPTOR_TYPE,
    0,
    0,
	NUM_ENDPOINTS,
	USB_CLASS_CODE_TEST_CLASS_DEVICE,
	USB_SUBCLASS_CODE_TEST_CLASS_D12,
	USB_PROTOCOL_CODE_TEST_CLASS_D12,
	0
};

//端点描述符
code USB_ENDPOINT_DESCRIPTOR EP1_TXDescr =
{
	sizeof(USB_ENDPOINT_DESCRIPTOR),
	USB_ENDPOINT_DESCRIPTOR_TYPE,
	0x81,
	USB_ENDPOINT_TYPE_INTERRUPT,
	SWAP(EP1_PACKET_SIZE),
	10
};

code USB_ENDPOINT_DESCRIPTOR EP1_RXDescr =
{
	sizeof(USB_ENDPOINT_DESCRIPTOR),
	USB_ENDPOINT_DESCRIPTOR_TYPE,
	0x1,
	USB_ENDPOINT_TYPE_INTERRUPT,
	SWAP(EP1_PACKET_SIZE),
	10
};

code USB_ENDPOINT_DESCRIPTOR EP2_TXDescr =
{
	sizeof(USB_ENDPOINT_DESCRIPTOR),
	USB_ENDPOINT_DESCRIPTOR_TYPE,
	0x82,
	USB_ENDPOINT_TYPE_BULK,
	SWAP(EP2_PACKET_SIZE),
	10
};

code USB_ENDPOINT_DESCRIPTOR EP2_RXDescr =
{
	sizeof(USB_ENDPOINT_DESCRIPTOR),
	USB_ENDPOINT_DESCRIPTOR_TYPE,
	0x2,
	USB_ENDPOINT_TYPE_BULK,
	SWAP(EP2_PACKET_SIZE),
	10
};