reset_pb1000.s

MIPS下的boottloader yamon 的源代码

	/* RCE0 */
	li		t1, MEM_STCFG0
	sw		t1, mem_stcfg0(t0)
	li		t1, MEM_STTIME0
	sw		t1, mem_sttime0(t0)
	li		t1, MEM_STADDR0
	sw		t1, mem_staddr0(t0)

	/* RCE1 */
	li		t1, MEM_STCFG1
	sw		t1, mem_stcfg1(t0)
	li		t1, MEM_STTIME1
	sw		t1, mem_sttime1(t0)
	li		t1, MEM_STADDR1
	sw		t1, mem_staddr1(t0)

	/* RCE2 */
	li		t1, MEM_STCFG2
	sw		t1, mem_stcfg2(t0)
	li		t1, MEM_STTIME2
	sw		t1, mem_sttime2(t0)
	li		t1, MEM_STADDR2
	sw		t1, mem_staddr2(t0)

	/* RCE3 */
	li		t1, MEM_STCFG3
	sw		t1, mem_stcfg3(t0)
	li		t1, MEM_STTIME3
	sw		t1, mem_sttime3(t0)
	li		t1, MEM_STADDR3
	sw		t1, mem_staddr3(t0)

	sync

	/*
	 * Step 15) Set peripherals to a known state
	 */
	li		t0, AU1000_IC0_ADDR
	li		t1, 0xFFFFFFFF
	sw		t1, ic_cfg0clr(t0)
	sw		t1, ic_cfg1clr(t0)
	sw		t1, ic_cfg2clr(t0)
	sw		t1, ic_srcset(t0)
	sw		t1, ic_assignset(t0)
	sw		t1, ic_wakeclr(t0)
	sw		t1, ic_maskclr(t0)
	sw		t1, ic_risingclr(t0)
	sw		t1, ic_fallingclr(t0)
	sw		zero, ic_testbit(t0)
	sync

	li		t0, AU1000_IC1_ADDR
	li		t1, 0xFFFFFFFF
	sw		t1, ic_cfg0clr(t0)
	sw		t1, ic_cfg1clr(t0)
	sw		t1, ic_cfg2clr(t0)
	sw		t1, ic_srcset(t0)
	sw		t1, ic_assignset(t0)
	sw		t1, ic_wakeclr(t0)
	sw		t1, ic_maskclr(t0)
	sw		t1, ic_risingclr(t0)
	sw		t1, ic_fallingclr(t0)
	sw		zero, ic_testbit(t0)
	sync

	li		t0, AU1000_SYS_ADDR
	sw		zero, sys_freqctrl0(t0)
	sw		zero, sys_freqctrl1(t0)
	sw		zero, sys_clksrc(t0)
	sw		zero, sys_pininputen(t0)
	sync

	li		t0, AU1000_AC97_ADDR
	li		t1, 0x2
	sw		t1, ac97_enable(t0)
	sync

	li		t0, AU1000_USBH_ADDR
	li		t1, usbh_enable
	addu	t0, t1, t0
	sw		zero, 0(t0)
	sync

	li		t0, AU1000_USBD_ADDR
	sw		zero, usbd_enable(t0)
	sync

	li		t0, AU1000_IRDA_ADDR
	sw		zero, irda_enable(t0)
	sync

	li		t0, AU1000_MACEN_ADDR
	sw		zero, macen_mac0(t0)
	sw		zero, macen_mac1(t0)
	sync

	li		t0, AU1000_I2S_ADDR
	li		t1, 0x02
	sw		t1, i2s_enable(t0)

	li		t0, AU1000_UART0_ADDR
	sw		zero, uart_enable(t0)
	sync

	li		t0, AU1000_UART1_ADDR
	sw		zero, uart_enable(t0)
	sync

	li		t0, AU1000_UART2_ADDR
	sw		zero, uart_enable(t0)
	sync

	li		t0, AU1000_UART3_ADDR
	sw		zero, uart_enable(t0)
	sync

	li		t0, AU1000_SSI0_ADDR
	li		t1, 0x02
	sw		t1, ssi_enable(t0)
	sync

	li		t0, AU1000_SSI1_ADDR
	li		t1, 0x02
	sw		t1, ssi_enable(t0)
	sync

	/*
	 * Step 16) Determine cause of reset
	 */
	/* wait 10mS to debounce external signals */
	li		t1, MEM_1MS*10
1:	add		t1, -1
	bne		t1, zero, 1b
	nop

	li		t0, AU1000_SYS_ADDR
	lw		t1, sys_wakesrc(t0)

	/* Clear sys_wakemsk to prevent false events */
	sw		zero, sys_wakemsk(t0)
	sync

	/* Clear sys_wakesrc */
	//sw		zero, sys_wakesrc(t0)
	sync

	/* Check for Hardware Reset */
	andi	t2, t1, 0x01
	bne		zero, t2, hardwarereset
	nop

	/* Check for Sleep Wakeup */
	andi	t2, t1, 0x02
	bne		zero, t2, sleepwakeup
	nop

	/* Assume run-time reset */
	beq		zero, zero, runtimereset
	nop

/********************************************************************/

hardwarereset:

	/*
	 * Step 1) Initialize SDRAM
	 */
	bal		initSDRAM
	nop

	/*
	 * Step 2) Initialize BOARD
	 */
	bal		initBOARD
	nop

	/*
	 * Step 3) Invoke application
	 */
	beq		zero, zero, alldone
	nop

/********************************************************************/

runtimereset:

	/*
	 * Step 1) Initialize SDRAM
	 */
	bal		initSDRAM
	nop

	/*
	 * Step 2) Initialize BOARD
	 */
	bal		initBOARD
	nop

	/*
	 * Step 3) Invoke application
	 */
	beq		zero, zero, alldone
	nop

/********************************************************************/

sleepwakeup:

	/*
	 * Step 1) Initialize SDRAM. The SDRAM must be in self-refresh mode.
	 */
	bal		wakeupSDRAM	
	nop

	/*
	 * Step 2) Initialize BOARD
	 */
	bal		initBOARD
	nop

	/*
	 * Step 3) Invoke application
	 */
	la		t0, AU1000_SYS_ADDR
	lw		sp, sys_scratch0(t0)
	lw		ra, sys_scratch1(t0)

	jr		ra
	nop

/********************************************************************/

	/*
	 * This routine initializes the SDRAM controller from Initial
	 * Power-up Reset or Running Reset.
	 */
initSDRAM:

	/* Only perform SDRAM init if running from ROM/Flash */
	addu	t2, ra, zero	/* preserve ra */
    bal		getPC
    nop
getPC:
    lui		t0, 0x1F00      /* ROM/flash address? */
    and		t1, t0, ra
	addu	ra, t2, zero	/* restore ra */
    bne		t0, t1, initSDRAMdone
    nop

	/* wait 1mS before setup */
	li		t1, MEM_1MS
1:	add		t1, -1
	bne		t1, zero, 1b
	nop

	li		t0, AU1000_MEM_ADDR
	li		t1, MEM_SDMODE0
	sw		t1, mem_sdmode0(t0)

	li		t1, MEM_SDMODE1
	sw		t1, mem_sdmode1(t0)

	li		t1, MEM_SDMODE2
	sw		t1, mem_sdmode2(t0)
	
	li		t1, MEM_SDADDR0
	sw		t1, mem_sdaddr0(t0)

	li		t1, MEM_SDADDR1
	sw		t1, mem_sdaddr1(t0)

	li		t1, MEM_SDADDR2
	sw		t1, mem_sdaddr2(t0)

	sync

	li		t1, MEM_SDREFCFG_D
	sw		t1, mem_sdrefcfg(t0)
	sync

	sw		zero, mem_sdprecmd(t0)
	sync

	sw		zero, mem_sdautoref(t0)
	sync

	sw		zero, mem_sdautoref(t0)
	sync

	li		t1, MEM_SDREFCFG_E
	sw		t1, mem_sdrefcfg(t0)
	sync

	li		t1, MEM_SDWRMD0
	sw		t1, mem_sdwrmd0(t0)		
	sync

	li		t1, MEM_SDWRMD1
	sw		t1, mem_sdwrmd1(t0)		
	sync

	li		t1, MEM_SDWRMD2
	sw		t1, mem_sdwrmd2(t0)
	sync

	/* wait 1mS after setup */
	li		t1, MEM_1MS
1:	add		t1, -1
	bne		t1, zero, 1b
	nop

initSDRAMdone:
	jr		ra
	nop

/********************************************************************/

wakeupSDRAM:

	/*
	 * With SDRAM in self refresh mode, update the
	 * ADDR, MODE and refresh registers
	 */
	li		t0, AU1000_MEM_ADDR

	li		t1, MEM_SDMODE0
	sw		t1, mem_sdmode0(t0)

	li		t1, MEM_SDMODE1
	sw		t1, mem_sdmode1(t0)

	li		t1, MEM_SDMODE2
	sw		t1, mem_sdmode2(t0)
	
	li		t1, MEM_SDADDR0
	sw		t1, mem_sdaddr0(t0)

	li		t1, MEM_SDADDR1
	sw		t1, mem_sdaddr1(t0)

	li		t1, MEM_SDADDR2
	sw		t1, mem_sdaddr2(t0)

	/*
	 * Perform burst refresh of 4096 rows
	 */
	li		t1, 4096
burstrefresh:
	sw		zero, mem_sdautoref(t0)
	bne		zero, t1, burstrefresh
	addi	t1, t1, -1

	li		t1, MEM_SDREFCFG_E
	sw		t1, mem_sdrefcfg(t0)

	sync

	jr		ra
	nop

/********************************************************************/

initBOARD:

	/*
	 * External and/or board-specific peripheral initialization
	 */

	/*
	 * Establish MUXed pin functionality
	 *
	 *  CS=0
	 * USB=1 USBH
	 *  U3=0 UART3
	 *  U2=0 UART2
	 *  U1=0 UART1
	 * SRC=0 GPIO6
	 * EX1=0 GPIO3
	 * EX0=0 GPIO2
	 * IRF=0 GPIO15
	 * UR3=1 UART3
	 * I2D=1 I2SDI
	 * I2S=0 I2S
	 * NI2=0 MAC1
	 *  U0=0 UART0
	 * IRD=0 IRTXD
	 * A97=0 AC97
	 *  S0=1 GPIO18:16
	 */
	li		t0, AU1000_SYS_ADDR
	li		t1,(1<<15)|(1<<7)|(1<<6)|(1<<0)
	sw		t1, sys_pinfunc(t0)

	/*
	 * Establish GPIO direction
	 *
	 * GPIO0 Input (Test pin)
	 * GPIO1 Input (Test pin)
	 * GPIO2 Input (I2S clock output not setup here)
	 * GPIO3 Input (Test pin)
	 * GPIO4 Output USB Power Enable#
	 * GPIO5 Output USB Power Enable#
	 * GPIO6 Input Push Button S8
	 * GPIO7 Input (Test pin)
	 * GPIO8 I2S
	 * GPIO9  UART3
	 * GPIO10 UART3
	 * GPIO11 UART3
	 * GPIO12 UART3
	 * GPIO13 UART3
	 * GPIO14 UART3
	 * GPIO15 Input CPLD IRQ#
	 * GPIO16 Input (External touch screen not setup here)
	 * GPIO17 Input (External touch screen not setup here)
	 * GPIO18 Input (External touch screen not setup here)
	 * GPIO19 IRDA
	 * GPIO20 UART0
	 * GPIO21 UART1
	 * GPIO22 UART2
	 * GPIO23 UART3
	 * GPIO24 MAC1
	 * GPIO25 MAC1
	 * GPIO26 MAC1
	 * GPIO27 MAC1
	 * GPIO28 MAC1
	 * GPIO29 I2S
	 * GPIO30 I2S
	 * GPIO31 I2S
	 */
	li		t1, 0x000780CF
	sw		t1, sys_trioutclr(t0)
	sync
	li		t1, 0x00000030
	sw		t1, sys_outputclr(t0)
	sync

	/*
	 * Establish CLOCKing
	 *
	 * FREQ5: unused
	 * FREQ4: unused
	 * FREQ3: unused
	 * FREQ2: USBH, USBD, IrDA (48MHz from AUXPLL)
	 * FREQ1: unused
	 * FREQ0: unused
	 */
	li		t0, AU1000_SYS_ADDR
	li		t1, (0<<22)|(1<<21)|(1<<20)
	sw		t1, sys_freqctrl0(t0)
	li		t1, (4<<12)|(0<<11)|(0<<10)|(4<<7)|(0<<6)|(0<<5)|(4<<2)|(0<<1)|(0<<0)
	sw		t1, sys_clksrc(t0)
	sync

	/* Ensure PCMCIA interface disabled */
	li		t0, 0xBE000000
	sw		zero, 0(t0) /* Voltage register */
	li		t1, 0xA000
	sw		t1, 4(t0) /* Misc register */

	jr		ra
	nop

/********************************************************************/

alldone:

	/*
	 * Prepare to invoke application main()
	 */
	.set reorder

/********************************************************************/