joint_axis_zero.txt

proe5.0野火版下载(中文版免费下载)

# {100} (100) [0] joint_axis_zero.Label
Motion Axis Settings
运动轴设置

# [1] JointNameLayout.Label
Select Motion Axis
选取运动轴

# [2] ReferenceTab.Label
Zero Refs
零参照

# [3] body1Ref_layout.Label
Green Body Reference
绿色主体参照

# [4] Body1SelButton.HelpText
Select a point or plane on the green body \nto indicate the zero reference on that body. \nThe motion axis will read zero when the \nreferences on the two bodies are aligned.
在绿色主体上选取一个点或平面\n以指出该主体上的零参照。\n在两个主体上的参照对齐时，\n运动轴处将为零。

# [5] bod2Ref_layout.Label
Orange Body Reference
橙色主体参照

# [6] Body2SelButton.HelpText
Select a point or plane on the orange body \nto indicate the zero reference on that body. \nThe motion axis will read zero when the \nreferences on the two bodies are aligned.
在橙色主体上选取一个点或平面\n以指出该主体上的零参照。\n当两个主体上的参照对齐时，\n运动轴处将为零。

# [7] SetReferenceToggle.Label
Specify References
指定参照

# [8] AsmConfigTab.Label
Regen Value
再生值

# [9] SetRegenToggle.Label
Specify Regeneration Value
指定再生值

# [10] SetRegenToggle.HelpText
zzz
zzz

# [11] regen_layout.Label
Regeneration Value
再生值

# [12] RegenValue.HelpText
Enter a value to be used whenever\nthe assembly is regenerated.\n
输入再生组件时\n将用到的值。\n

# [13] RegenValueHelp.Value
Regen Value disabled. To enable, either define Zero References in the previous tab (recommended), or redefine the motion axis such that it does not reference datum axes.
再生值被禁用。如果要启用，可在先前的选项卡中定义零参照 (推荐)，或重定义运动轴，使其不参照基准轴。

# [14] PropertiesTab.Label
Properties
属性

# [15] SetLimitToggle.Label
Enable Limits
启用限制

# [16] minvalue_layout.Label
Motion Axis Limits
运动轴限制

# [17] MinimumLabel.Label
Minimum
最小值

# [18] MinimumValue.HelpText
Enter the lower limit. For an angle, \nenter a value between -180 and 180 degrees \nin counter clockwise direction.
输入下限。对于角度，输入\n一个逆时针方向-180到\n180度之间的值。

# [19] MinimumUnits.Value
mm
mm

# [20] MaximumLabel.Label
Maximum
最大值

# [21] MaximumValue.HelpText
Enter the upper limit. For an angle, \nenter a value between -180 and 180 degrees \nin counter clockwise direction.
输入上限。对于角度，输入\n一个逆时针方向-180到\n180度之间的值。

# [22] RestCoef.Label
Coefficient of Restitution
恢复系数

# [23] CofRestLabel.Label
 =  
 =  

# [24] CofRestValue.HelpText
Enter the coefficient of restitution. \nEnter a value between 0.0 and 1.0.
输入恢复系数。\n输入一个0.0和1.0之间的值。

# [25] SetFrictionToggle.Label
Enable Friction
启用摩擦

# [26] JointFriction.Label
Motion Axis Friction
运动轴摩擦

# [27] MuSLabel.Label
 =  
 =  

# [28] MuDLabel.Label
 =  
 =  

# [29] RadiusLabel.Label
 =  
 =  

# [30] MuSValue.HelpText
Enter the coefficient of static friction.\nEnter a value between 0.0 and 1.0.
输入静摩擦系数。\n输入 0.0 到 1.0 之间的一个值。

# [31] MuDValue.HelpText
Enter the coefficient of kinetic friction.\nEnter a value between 0.0 and 1.0.
输入动摩擦系数。\n输入 0.0 到 1.0 之间的一个值。

# [32] RadiusValue.HelpText
Enter a value for contact radius.
输入接触半径值。

# [33] RadiusUnits.Value
mm
mm

# [34] ValueDisplayLayout.Label
Motion Axis Position
运动轴位置

# [35] CurrentValue.HelpText
The value of the motion axis for the bodies in\ntheir current positions is reported here. \nYou may also enter a value, in which case\nthe bodies will be temporarily repositioned\nto reflect your entry.
当前位置主体的运动轴的值\n在此报告。\n您还可输入一个值，在此\n情况下主体将暂时重新\n定位以反映该输入。

# [36] MakeZeroButton.Label
Make Zero
生成零点

# [37] MakeZeroButton.HelpText
Make current configuration\nas zero for the motion axis.
使运动轴的当前\n配置为零。

# [38] OkButton.Label
OK
确定

# [39] ApplyButton.Label
Preview
预览

# [40] CancelButton.Label
Cancel
取消